Ceramic material composite

Because the neutronics properties are major drawbacks for the use of these metals as cladding materials for Generation IV reactors, use of these materials as thin liners sandwiched with ceramic material composite (CMC), such as SiC/SiC composite, tubes was proposed [55]. In this system responsibilities of creep resistance, thermal stability, corrosion resistance, and gas tightness if necessary, are shared by the triplex layers as designed for CMC/steel composite pipes [56]. 

Cera.micA.bla.tors, Several types of subliming or melting ceramic ablators have been used or considered for use in dielectric appHcations particularly with quartz or boron nitride [10043-11 -5] fiber reinforcements to form a nonconductive char. Fused siHca is available in both nonporous (optically transparent) and porous (sHp cast) forms. Ford Aerospace manufactures a 3D siHca-fiber-reinforced composite densified with coUoidal siHca (37). The material, designated AS-3DX, demonstrates improved mechanical toughness compared to monolithic ceramics. Other dielectric ceramic composites have been used with performance improvements over monolithic ceramics (see COMPOSITE MATERIALS, CERAMIC MATRIX). 

Ferroelectric Ceramic—Polymer Composites. The motivation for the development of composite ferroelectric materials arose from the need for a combination of desirable properties that often caimot be obtained in single-phase materials. For example, in an electromechanical transducer, the piezoelectric sensitivity might be maximized and the density minimized to obtain a good acoustic matching with water, and the transducer made mechanically flexible to conform to a curved surface (see COMPOSITE MATERIALS, CERAMiC-MATRix). 

The development of active ceramic-polymer composites was undertaken for underwater hydrophones having hydrostatic piezoelectric coefficients larger than those of the commonly used lead zirconate titanate (PZT) ceramics (60—70). It has been demonstrated that certain composite hydrophone materials are two to three orders of magnitude more sensitive than PZT ceramics while satisfying such other requirements as pressure dependency of sensitivity. The idea of composite ferroelectrics has been extended to other appHcations such as ultrasonic transducers for acoustic imaging, thermistors having both negative and positive temperature coefficients of resistance, and active sound absorbers. 

Over time a large variety of materials have been used, including ivory, stainless steel, chromium—cobalt, and ceramics for the acetabular component. None proved sufficient. The implant material composition must provide a smooth surface for joint articulation, withstand hip joint stresses from normal loads, and the substance must disperse stress evenly to the cement and surrounding bone. 

J. D. Buckley, ed.. Advanced Materials, Composite Carbon, Preparation Symposium, American Ceramics Society, Inc., Columbus, Ohio, 1972. Papers on composite materials including carbon and graphite or nitride composites. 

Development of practical and low cost separators has been an active area of ceU development. CeU separators must be compatible with molten lithium, restricting the choice to ceramic materials. Early work employed boron nitride [10043-11-5] BN, but a more desirable separator has been developed using magnesium oxide [1309-48-4], MgO, or a composite ofMgO powder—BN fibers. Corrosion studies have shown that low carbon steel or... 

Reinforcements. The high modulus, high intrinsic strength, and temperature stabiHty make SiC, in the form of whiskers, platelets, and fibers, a promising candidate reinforcement material for metal, polymer, and ceramic matrix composites (qv). 

Directed Oxidation of a Molten Metal. Directed oxidation of a molten metal or the Lanxide process (45,68,91) involves the reaction of a molten metal with a gaseous oxidant, eg, A1 with O2 in air, to form a porous three-dimensional oxide that grows outward from the metal/ceramic surface. The process proceeds via capillary action as the molten metal wicks into open pore channels in the oxide scale growth. Reinforced ceramic matrix composites can be formed by positioning inert filler materials, eg, fibers, whiskers, and/or particulates, in the path of the oxide scale growth. The resultant composite is comprised of both interconnected metal and ceramic. Typically 5—30 vol % metal remains after processing. The composite product maintains many of the desirable properties of a ceramic however, the presence of the metal serves to increase the fracture toughness of the composite. 

In the broad range of ceramic materials that are used for electrical and electronic apphcations, each category of material exhibits unique property characteristics which directiy reflect composition, processing, and microstmcture. Detailed treatment is given primarily to those property characteristics relating to insulation behavior and electrical conduction processes. Further details concerning the more specialized electrical behavior in ceramic materials, eg, polarization, dielectric, ferroelectric, piezoelectric, electrooptic, and magnetic phenomena, are covered in References 1—9. 

---