Cavity number

The stamp associated with the extreme hardness values (number 7, Fig. 4.12, left use STAMP.dat with program MULTI) is the next suspect It is identified and inspected on disassembly of the tablet press Due to mechanical wear, the movement of the stamp assembly is such that an above-average amount of granulate drops into cavity number 7, and is thus compressed to the limiting hardness supported by the granulate. The hardness for stamps 4, 8, and 11 tends to be low, and high for 12, but the data is insufficient to come to definite conclusions for these tools. The tablets from these stamps contaminated what would otherwise been a fairly acceptable product. Because... 

Nomenclature 5 6 indicates 12 pentagonal and 8 hexagonal sides in a cavity numbers along lines indicate the number of cavities in each unit crystal structure. The rightmost numbers indicate the water molecules per crystal structure... 

Cavity numbers should be engraved in the mold. The letters should be 2.4 mm high and 0.18 mm deep. 

Macropolycyclic receptors (cryptands) possess a tridimensional cavity in which guest species can be lodged. By modulating the molecular topology of the host molecule, /. e., size and shape of the cavity, number and type of donors and flexibility of the structure, the coordination of many different substrates (metal cations, ammonium ions, anionic species or neutral molecules) can be achieved. 

Multi-component molds are mostly, especially with high cavity numbers, equipped with a hotrunner system which must provide a perfect heat separation (Figure 1.75). 

Any cavity contains an infinite number of electromagnetic modes. For radiation confined to a perfectly conducting cubical cavity of volume V= L, the modes are given by the electric field components of the fomi ... 

There are differences between photons and phonons while the total number of photons in a cavity is infinite, the number of elastic modes m a finite solid is finite and equals 3N if there are N atoms in a three-dimensional solid. Furthennore, an elastic wave has tliree possible polarizations, two transverse and one longimdinal, in contrast to only... 

The sharpness of the frequency response of a resonant system is conunonly described by a factor of merit, called the quality factor, Q=v/Av. It may be obtained from a measurement of the frill width at half maxuuum Av, of the resonator frequency response curve obtained from a frequency sweep covering the resonance. The sensitivity of a system (proportional to the inverse of tlie minimum detectable number of paramagnetic centres in an EPR cavity) critically depends on the quality factor... 

IS added to the short-range molecule-molecule interaction. Problems with the reaction ethod may arise from discontinuities in the energy and/or force when the number of les j rvithin the cavity of the molecule i changes. These problems can be avoided by dng a switching function for molecules that are near the reaction field boundary. 

Tlie molecular volume Vm can in turn be obtained by dividing the molecular weight by density or from refractivity measurements is Avogadro s number. The cavity radius (... 

The constants K depend upon the volume of the solvent molecule (assumed to be spherica in slrape) and the number density of the solvent. ai2 is the average of the diameters of solvent molecule and a spherical solute molecule. This equation may be applied to solute of a more general shape by calculating the contribution of each atom and then scaling thi by the fraction of fhat atom s surface that is actually exposed to the solvent. The dispersioi contribution to the solvation free energy can be modelled as a continuous distributioi function that is integrated over the cavity surface [Floris and Tomasi 1989]. 

The self-consistent reaction held (SCRF) method is an adaptation of the Poisson method for ah initio calculations. There are quite a number of variations on this method. One point of difference is the shape of the solvent cavity. Various models use spherical cavities, spheres for each atom, or an isosurface... 

The working out of these ideas will be illustrated by reference to a number of simple pore models the cylinder, the parallel-sided slit, the wedge-shape and the cavity between spheres in contact. 

Fig. 4J Langmuir plots (a) for propane on 5A zeolite (courtesy Ruthven) (fc) for carbon monoxide on zeolite CaY-54 (courtesy Stone). In (a) the adsorption is expressed in terms of number C of molecules of adsorbate per cavity in (b), as m (stp).

In practice the laser can operate only when n, in Equation (9.2), takes values such that the corresponding resonant frequency v lies within the line width of the transition between the two energy levels involved. If the active medium is a gas this line width may be the Doppler line width (see Section 2.3.2). Figure 9.3 shows a case where there are twelve axial modes within the Doppler profile. The number of modes in the actual laser beam depends on how much radiation is allowed to leak out of the cavity. In the example in Figure 9.3 the output level has been adjusted so that the so-called threshold condition allows six axial modes in the beam. The gain, or the degree of amplification, achieved in the laser is a measure of the intensity. 

Cyclodextrins are macrocyclic compounds comprised of D-glucose bonded through 1,4-a-linkages and produced enzymatically from starch. The greek letter which proceeds the name indicates the number of glucose units incorporated in the CD (eg, a = 6, /5 = 7, 7 = 8, etc). Cyclodextrins are toroidal shaped molecules with a relatively hydrophobic internal cavity (Fig. 6). The exterior is relatively hydrophilic because of the presence of the primary and secondary hydroxyls. The primary C-6 hydroxyls are free to rotate and can partially block the CD cavity from one end. The mouth of the opposite end of the CD cavity is encircled by the C-2 and C-3 secondary hydroxyls. The restricted conformational freedom and orientation of these secondary hydroxyls is thought to be responsible for the chiral recognition inherent in these molecules (77). 

Because cycle time to inject, flow, set, open, eject, and close is finite, and the face area or platen size is limited, the effective mol ding area is increased by increasing the number of mold cavities so that the number of finished pieces per cycle may be multipHed many times. 

Vacuum Radiation Furnaces. Vacuum furnaces are used where the work can be satisfactorily processed only in a vacuum or in a protective atmosphere. Most vacuum furnaces use molybdenum heating elements. Because all heat transfer is by radiation, metal radiation shields ate used to reduce heat transfer to the furnace casing. The casing is water-cooled and a sufficient number of radiation shields between the inner cavity and the casing reduce the heat flow to the casing to a reasonable level. These shields are substitutes for the insulating refractories used in other furnaces. 

---