Catalytic reactor process

The equations are also coupled by the mass transfer coefficient This is the standard mass transfer problem we encountered with catalytic reactions. As with catalytic reactors, processes are very often limited by mass transfer so that the kinetics become unimportant in predicting performance. 

Most fluidized bed partial oxidation processes are operated in the turbulent flow regime of fluidization. However, DuPont operated a circulating fluidized bed catalytic reactor process for maleic anhydride production in Spain, featuring regeneration of the catalyst (by oxidation) on the downcomer side of the circulating system. 

In pellet model analysis in which the convective transport of heat and species mass in porous catalyst pellets have to be taken into account simulating catalytic reactor processes, either the Maxweli-Stefan mass flux equations (2.416) or dusty gas model for the mass fluxes (2.513) might be used. The possible viscous flow in the catalyst pores is driven by a pressure gradient induced by the potential non-uniform spatial species composition and temperature evolution created by the chemical reactions. 

Catalytic methanation processes include (/) fixed or fluidized catalyst-bed reactors where temperature rise is controlled by heat exchange or by direct cooling using product gas recycle (2) through wall-cooled reactor where temperature is controlled by heat removal through the walls of catalyst-filled tubes (J) tube-wall reactors where a nickel—aluminum alloy is flame-sprayed and treated to form a Raney-nickel catalyst bonded to the reactor tube heat-exchange surface and (4) slurry or Hquid-phase (oil) methanation. 

Properties. Table 4 contains typical gasoline quaUty data from the New Zealand plant (67). MTG gasoline typically contains 60 vol % saturates, ie, paraffins and naphthenes 10 vol % olefins and 30 vol % aromatics. Sulfur and nitrogen levels in the gasoline are virtually lul. The MTG process produces ca 3—7 wt % durene [95-93-2] (1,2,4,5-tetra-methylbenzene) but the level is reduced to ca 2 wt % in the finished gasoline product by hydrodealkylation of the durene in a separate catalytic reactor. 

A derivative of the Claus process is the Recycle Selectox process, developed by Parsons and Unocal and Hcensed through UOP. Once-Thm Selectox is suitable for very lean acid gas streams (1—5 mol % hydrogen sulfide), which cannot be effectively processed in a Claus unit. As shown in Figure 9, the process is similar to a standard Claus plant, except that the thermal combustor and waste heat boiler have been replaced with a catalytic reactor. The Selectox catalyst promotes the selective oxidation of hydrogen sulfide to sulfur dioxide, ie, hydrocarbons in the feed are not oxidized. These plants typically employ two Claus catalytic stages downstream of the Selectox reactor, to achieve an overall sulfur recovery of 90—95%. 

Process Description. Reactors used in the vapor-phase synthesis of thiophene and aLkylthiophenes are all multitubular, fixed-bed catalytic reactors operating at atmospheric pressure, or up to 10 kPa and with hot-air circulation on the shell, or salt bath heating, maintaining reaction temperatures in the range of 400—500°C. The feedstocks, in the appropriate molar ratio, are vaporized and passed through the catalyst bed. Condensation gives the cmde product mixture noncondensable vapors are vented to the incinerator. 

The most dominant catalytic process in the United States is the fluid catalytic cracking process. In this process, partially vaporized medium-cut petroleum fractions called gas oils are brought in contact with a hot, moving, freshly regenerated catalyst stream for a short period of time at process conditions noted above. Spent catalyst moves continuously into a regenerator where deposited coke on the catalyst is burnt off. The hot, freshly regenerated catalyst moves back to the reactor to contact the hot gas oil (see Catalysts, regeneration). 

This is a desirable side reaction in the first catalytic reactor of the Claus sulfur recovery process. 

Fig. 1. UOP catalytic condensation process for cumene synthesis. R = reactor RECT = rectifier DP = depropanizer RC = recycle column ...

Two quite successful rate equations of catalytic industrial processes are cited by Rase Chemical Reactor De.sign for Proce.s.s Plants, vol. 2, Wiley, 1977) ... 

Fluidized bed catalytic reactors seem to have so many advantageous features that they were considered for many processes. One of the advantages is their excellent heat transfer characteristics, due to the large catalyst surface to volume ratio, so very little temperature difference is needed for heat transfer. This would make temperature control problem-free. The second is the uniformity of reaction conditions in the bed. 

There are two basic types of packed-bed reactors those in which the solid is a reactant and those in which the solid is a catalyst. Many e.xaniples of the first type can be found in the extractive metallurgical industries. In the chemical process industries, the designer normally meets the second type, catalytic reactors. Industrial packed-bed catalylic reactors range in size from units with small tubes (a few centimeters in diameter) to large-diameter packed beds. Packed-bed reactors are used for gas and gas-liquid reactions. Heat transfer rates in large-diameter packed beds are poor and where high heat transfer rates are required, Jluidized beds should be considered. ... 

The Houdry fixed-bed cyclic units were soon displaced in the 1940s by the superior Fluid Catalytic Cracking process pioneered by Warren K. Lewis of MIT and Eger Murphree and his team of engineers at Standard Oil of Newjersey (now Exxon). Murphree and his team demonstrated that hundreds of tons of fine catalyst could be continuously moved like a fluid between the cracking reactor and a separate vessel for... 

Deep catalytic cracking (DCC) is a catalytic cracking process which selectively cracks a wide variety of feedstocks into light olefins. The reactor and the regenerator systems are similar to FCC. However, innovation in the catalyst development, severity, and process variable selection enables DCC to produce more olefins than FCC. In this mode of operation, propylene plus ethylene yields could reach over 25%. In addition, a high yield of amylenes (C5 olefins) is possible. Figure 3-7 shows the DCC process and Table 3-10 compares olefins produced from DCC and FCC processes. ... 

Nickel catalysts were used in most of the methanation catalytic studies they have a rather wide range of operating temperatures, approximately 260°-538°C. Operation of the catalytic reactors at 482°-538°C will ultimately result in carbon deposition and rapid deactivation of the catalysts (10). Reactions below 260°C will usually result in formation of nickel carbonyl and also in rapid deactivation of the catalysts. The best operating range for most fixed-bed nickel catalysts is 288°-482 °C. Several schemes have been proposed to limit the maximum temperature in adiabatic catalytic reactors to 482°C, and IGT has developed a cold-gas recycle process that utilizes a series of fixed-bed adiabatic catalytic reactors to maintain this temperature control. 

The IGT multistage cold-gas recycle methanation process has a built-in temperature control mechanism and a low recycle ratio. Much less recycle gas is used in this multistage operation than would be required if the same amount of conversion were achieved in a single vessel with all fresh feed and recycle gas added at the inlet to one large catalytic reactor. 

The kinetics of a complex catalytic reaction can be derived from the results obtained by a separate study of single reactions. This is important in modeling the course of a catalytic process starting from laboratory data and in obtaining parameters for catalytic reactor design. The method of isolation of reactions renders it possible to discover also some other reaction paths which were not originally considered in the reaction network. 

For the organic contaminants, the required bromine product quality wilt also be site specific. If the catalytic oxidation unit is dedicated to a single bromination process, phase separation and drying may be the only purification required. Contaminants in the recovered bromine which are either the starting materials or products of the original bromination reaction should not present a problem if present in bromine recycled to the bromination reactor. In this case, the catalytic reactor would be operated to minimize the formation of undesirable brominated byproducts. For example, if phenol is present in the waste HBr from a tribromo-phenol manufacturing process, minor tribromophenol contamination of the bromine recycled to the reactor should not be a problem. Similarly, fluorobenzene in bromine recycled to a fluorobenzene bromination process should not present a problem. 

---