Catalytic reaction active-site control

Lipases have also been used as initiators for the polymerization of lactones such as /3-bu tyro lac tone, <5-valerolactone, e-caprolactone, and macrolides.341,352-357 In this case, the key step is the reaction of lactone with die serine residue at the catalytically active site to form an acyl-enzyme hydroxy-terminated activated intermediate. This intermediate then reacts with the terminal hydroxyl group of a n-mer chain to produce an (n + i)-mer.325,355,358,359 Enzymatic lactone polymerization follows a conventional Michaelis-Menten enzymatic kinetics353 and presents a controlled character, without termination and chain transfer,355 although more or less controlled factors, such as water content of the enzyme, may affect polymerization rate and the nature of endgroups.360... 

One form of biological poisoning mirrors the effect of lead on a catalytic converter. The activity of an enzyme is destroyed if an alien substrate attaches too strongly to the enzyme s active site, because then the site is blocked and made unavailable to the true substrate (Fig. 13.42). As a result, the chain of biochemical reactions in the cell stops, and the cell dies. The action of nerve gases is believed to stem from their ability to block the enzyme-controlled reactions that allow impulses to travel through nerves. Arsenic, that favorite of fictional poisoners, acts in a similar way. After ingestion as As(V) in the form of arsenate ions (As043 ), it is reduced to As(III), which binds to enzymes and inhibits their action. 

The advantages of microreactors, for example, well-defined control of the gas-liquid distributions, also hold for photocatalytic conversions. Furthermore, the distance between the light source and the catalyst is small, with the catalyst immobilized on the walls of the microchannels. It was demonstrated for the photodegradation of 4-chlorophenol in a microreactor that the reaction was truly kinetically controlled, and performed with high efficiency [32]. The latter was explained by the illuminated area, which exceeds conventional reactor types by a factor of 4-400, depending on the reactor type. Even further reduction of the distance between the light source and the catalytically active site might be possible by the use of electroluminescent materials [19]. The benefits of this concept have still to be proven. 

Analysis of the dynamics of SCR catalysts is also very important. It has been shown that surface heterogeneity must be considered to describe transient kinetics of NH3 adsorption-desorption and that the rate of NO conversion does not depend on the ammonia surface coverage above a critical value [79], There is probably a reservoir of adsorbed species which may migrate during the catalytic reaction to the active vanadium sites. It was also noted in these studies that ammonia desorption is a much slower process than ammonia adsorption, the rate of the latter being comparable to that of the surface reaction. In the S02 oxidation on the same catalysts, it was also noted in transient experiments [80] that the build up/depletion of sulphates at the catalyst surface is rate controlling in S02 oxidation. 

Moreover, the use of heat-flow calorimetry in heterogeneous catalysis research is not limited to the measurement of differential heats of adsorption. Surface interactions between adsorbed species or between gases and adsorbed species, similar to the interactions which either constitute some of the steps of the reaction mechanisms or produce, during the catalytic reaction, the inhibition of the catalyst, may also be studied by this experimental technique. The calorimetric results, compared to thermodynamic data in thermochemical cycles, yield, in the favorable cases, useful information concerning the most probable reaction mechanisms or the fraction of the energy spectrum of surface sites which is really active during the catalytic reaction. Some of the conclusions of these investigations may be controlled directly by the calorimetric studies of the catalytic reaction itself. 

The multi-functionality of metal oxides1,13 is one of the key aspects which allow realizing selectively on metal oxide catalysts complex multi-step transformations, such as w-butane or n-pentane selective oxidation.14,15 This multi-functionality of metal oxides is also the key aspect to implement a new sustainable industrial chemical production.16 The challenge to realize complex multi-step reactions over solid catalysts and ideally achieve 100% selectivity requires an understanding of the surface micro-kinetic and the relationship with the multi-functionality of the catalytic surface.17 However, the control of the catalyst multi-functionality requires the ability also to control their nano-architecture, e.g. the spatial arrangement of the active sites around the first centre of chemisorption of the incoming molecule.1... 

The catalytic performances of the supported catalysts clearly demonstrated the improvement in terms of activity or selectivity by such optimized catalytic systems. This improvement is related to a nanometer control of the critical characteristics of the active sites. Enhancement of the catalytic performances and the understanding of structure-reactivity relationships can only be achieved by advancing the understanding of different preparation methods, eventually leading to better control over the characteristics of the active sites at a nanometer scale. Moreover, new properties of these solids may be found, which could have a great impact on catalytic reactions. 

Section I reviews the new concepts and applications of nanotechnology for catalysis. Chapter 1 provides an overview on how nanotechnology impacts catalyst preparation with more control of active sites, phases, and environment of actives sites. The values of catalysis in advancing development of nanotechnology where catalysts are used to facilitate the production of carbon nanotubes, and catalytic reactions to provide the driving force for motions in nano-machines are also reviewed. Chapter 2 investigates the role of oxide support materials in modifying the electronic stmcture at the surface of a metal, and discusses how metal surface structure and properties influence the reactivity at molecular level. Chapter 3 describes a nanomotor driven by catalysis of chemical reactions. 

---