Catalytic properties, characterization

The typical industrial catalyst has both microscopic and macroscopic regions with different compositions and stmctures the surfaces of industrial catalysts are much more complex than those of the single crystals of metal investigated in ultrahigh vacuum experiments. Because surfaces of industrial catalysts are very difficult to characterize precisely and catalytic properties are sensitive to small stmctural details, it is usually not possible to identify the specific combinations of atoms on a surface, called catalytic sites or active sites, that are responsible for catalysis. Experiments with catalyst poisons, substances that bond strongly with catalyst surfaces and deactivate them, have shown that the catalytic sites are usually a small fraction of the catalyst surface. Most models of catalytic sites rest on rather shaky foundations. 

This reduction can also be carried out with molecular hydrogen and as such is probably not of any commercial interest. However, it is suited for the study of the catalytic properties of the ultrafine powders and serves as a characterization and optimization technique for the titanium nitride nanoparticles in this study. 

We have already mentioned that fundamental studies in catalysis often require the use of single crystals or other model systems. As catalyst characterization in academic research aims to determine the surface composition on the molecular level under the conditions where the catalyst does its work, one can in principle adopt two approaches. The first is to model the catalytic surface, for example with that of a single crystal. By using the appropriate combination of surface science tools, the desired characterization on the atomic scale is certainly possible in favorable cases. However, although one may be able to study the catalytic properties of such samples under realistic conditions (pressures of 1 atm or higher), most of the characterization is necessarily carried out in ultrahigh vacuum, and not under reaction conditions. 

The catalytic properties were characterized in a simplified manner by two parameters the maximal conversion Cm and the corresponding temperature Tm- The selectivity of NO conversion to N2 is always very high (> 98%). The formation of NO2 is marginal on these Cu catalysts. 

The above example outlines a general problem in immobilized molecular catalysts - multiple types of sites are often produced. To this end, we are developing techniques to prepare well-defined immobilized organometallic catalysts on silica supports with isolated catalytic sites (7). Our new strategy is demonstrated by creation of isolated titanium complexes on a mesoporous silica support. These new materials are characterized in detail and their catalytic properties in test reactions (polymerization of ethylene) indicate improved catalytic performance over supported catalysts prepared via conventional means (8). The generality of this catalyst design approach is discussed and additional immobilized metal complex catalysts are considered. 

The synthesis, characterization, and catalytic properties of materials obtained by the reaction of organometallic complexes of IIB, IVA, and VIA with metallic particles were studied extensively. Two types of materials may be obtained by... 

We will describe first the different methods of immobilization of catalysts, and highlight their advantages and disadvantages and their fields of application. We will then examine the properties of such supported complexes for the major classes of catalytic reactions. We will focus mainly on those studies where at least some characterization of the supported catalyst is given, unless the catalytic properties of the described system are outstanding the review is therefore far from being exhaustive. Finally, where possible, we will mention tests of recyclability, which are essential for the supported complex to be as a potential industrial catalyst. 

The supported aqueous phase methodology was applied to the system Pd(OAc)2/5 TPPTS, a catalytic precursor for the Trost-Tsuji reaction. The characterization of the solid by 31P MAS NMR confirms the presence of Pd°(TPPTS)3 as the main surface species. The catalytic properties of the solid were tested for the allylic substitution of E-cinnamylethylcarbonate by different nucleophiles such as ethyl acetoacetate, dimethyl malonate, morpholine, phenol, and 2-mercapto-pyridine. The absence of palladium leaching was demonstrated, and having solved the problem of water leaching from the solid to the organic phase, the SAP-Pd catalyst was successfully recycled several times without loss in its activity. It was used in a continuous flow experiment which... 

Das, T.K., Jacobs, G., Patterson, P.M., Conner, W.A., Li, J., and Davis, B.H. 2003. Fischer-Tropsch synthesis Characterization and catalytic properties of rhenium promoted cobalt alumina catalysts. Fuel 82 805-15. 

The main objective of this review is to summarize and critically analyze recent advances made in the characterization and catalytic properties of titanium silicate molecular sieves after the reviews of Notari (33) and Vayssilov (34) in 1996 and 1997, respectively. Of special interest are... 

The catalytic properties of a surface are determined by its composition and structure on the atomic scale. Hence, it is not sufficient to know that a surface consists of a metal and a promoter, say iron and potassium, but it is essential to know the exact structure of the iron surface, including defects, steps, etc., as well as the exact locations of the promoter atoms. Thus, from a fundamental point of view, the ultimate goal of catalyst characterization should be to look at the surface atom by atom, and under reaction conditions. The well-defined surfaces of single crystals offer the best likelihood of atom-by-atom characterization, although occasionally atomic scale information can be obtained from real catalysts under in situ conditions as well, as the examples in Chapter 9 show. 

T. K. Das, G. Jacobs, P. M. Patterson, W. A. Conner, J. Li and B. H. Davis, Fischer-Tropsch synthesis characterization and catalytic properties of rhenium promoted cobalt alumina catalysts, Fuel, 2003, 82, 805-815. 

In the present work ir, esr and microcalorimetry techniques were used to characterize the acid-base properties of acid ZSM-5 and ZSM-11 samples. Complementary studies by TEM, EDX-STEM and XPS were also carried out to determine the size and shape of zeolite particles and the A1 distribution within a particle. Catalytic properties for methanol conversion were also determined. 

---