Carbon surface coverage effects

Utilization of resonance effects can facilitate unenhanced Raman measurement of surfaces and make the technique more versatile. For instance, a fluorescein derivative and another dye were used as resonantly Raman scattering labels for hydroxyl and carbonyl groups on glassy carbon surfaces. The labels were covalently bonded to the surface, their fluorescence was quenched by the carbon surface, and their resonance Raman spectra could be observed at surface coverages of approximately 1%. These labels enabled assess to changes in surface coverage by C-OH and C=0 with acidic or alkaline pretreatment [4.293]. 

Direct measurements on metals such as iron, nickel and stainless steel have shown that adsorption occurs from acid solutions of inhibitors such as iodide ions, carbon monoxide and organic compounds such as amines , thioureas , sulphoxides , sulphidesand mer-captans. These studies have shown that the efficiency of inhibition (expressed as the relative reduction in corrosion rate) can be qualitatively related to the amount of adsorbed inhibitor on the metal surface. However, no detailed quantitative correlation has yet been achieved between these parameters. There is some evidence that adsorption of inhibitor species at low surface coverage d (for complete surface coverage 0=1) may be more effective in producing inhibition than adsorption at high surface coverage. In particular, the adsorption of polyvinyl pyridine on iron in hydrochloric acid at 0 < 0 -1 monolayer has been found to produce an 80% reduction in corrosion rate . 

Beyer and coworkers later extended these reactions to platinum clusters Ptn and have demonstrated that similar reaction sequences for the oxidation of carbon monoxide can occur with larger clusters [70]. In addition, they were able to demonstrate poisoning effects as a function of surface coverage and cluster size. A related sequence for Pt anions was proposed by Shi and Ervin who employed molecular oxygen rather than N2O as the oxidant [71]. Further, the group of Bohme has screened the mononuclear cations of almost the entire transition metal block for this particular kind of oxidation catalysis [72,73]. Another catalytic system has been proposed by Waters et al. in which a dimolybdate anion cluster brings about the oxidation of methanol to formaldehyde with nitromethane, however, a rather unusual terminal oxidant was employed [74]. 

In equation 5, C is amorphous carbon and CF2 changes to many perfluorocarbons, such as CF4, C2F6, etc., by secondary reactions. The surface coverage of graphite fluoride on the anode depends on the relative reaction rates of equations 4 and 5. Equation 6 has been introduced to analyze the wettability of the carbon surface with graphite fluoride formed on it.2 It shows the relationship between the fraction of effective surface for equation 3 per unit surface area of carbon (a) and the contact angle (0) of a fluorine gas bubble on the surface of the carbon electrode.2... 

The details of the sample preparation and studies of the nature of the supported-metal samples have been described in a paper dealing with the effect of surface coverage on the spectra of carbon monoxide chemisorbed on platinum, nickel, and palladium (1). The samples consist of small particles of metal dispersed on a nonporous silica which is produced commercially under the names Cabosil or Aerosil.f This type of silica is suitable as a support because it is relatively inert and has a small particle size (150-200 A.). The small particle size is important because it reduces the amount of radiation which is lost by scattering. A nonporous small particle form of gamma-alumina, known as Alon-C, is also available. This material is not so inert as the silica and will react with gases such as CO and CO2 at elevated temperatures. 

A variety of measurements, such as total carbon analysis and BET surface area, have been used to determine the effectiveness of the sily-lation reactions and the coverage of the silica surface. From these measurements the percentage of carbon on the surface can be calculated and is used to designate the degree of surface coverage. Values ranging from 2 to 30% carbon have been reported. 

Cl, acidic" carbon C2, typical as-reccived carbon C3, basic carbon, (b) Effect of pH on the /vnitrophenol surface coverage of carbons having different surface chemistry. (From Ref. 674 see al.so Fig. 32 and Section V.)... 

---