Carbon-based particulate materials

Biocompatibility claims for a particular form of carbon based on published results for a totally different form or structure should be carefully scrutinized. For example, to claim that carbon fibers have the same biological properties as bulk pyrolytic carbons or even that all pyrolytic carbons behave similarly is unjustified. In the case of fibers, geometry plays a significant role. It is well known that bulk materials may be well tolerated when the same material in particulate form may not. The lack of characterization and standardization can be devastating. 

Polymer materials are ubiquitous in our daily life. They often consist of more than one species of polymers and, therefore, can be called multicomponent systems, for example, polymer blends and block copolymers. Because of the repulsive interaction between the constituent polymers, multicomponent polymer materials often show phase separation. Organic-inorganic composites are another class of polymer-based multicomponent materials that have attracted considerable interest from researchers because they often exhibit unexpected properties synergistically derived from the constituents. Nanometer-sized particulate fillers, for example, carbon black (CB) and silica (Si) nanoparticles, are known to form hybrids with organic polymers, which show a significant increase in their static and dynamic moduli, strength, and thermal and electrical conductivities. 

Of the four commercial processes for the purification of carbon monoxide two processes are based on the absorption of carbon monoxide by salt solutions, the third uses either low temperature condensation or fractionation, and the fourth method utilizes the adsorption of carbon monoxide on a soHd adsorbent material. AH four processes use similar techniques to remove minor impurities. Particulates are removed in cyclones or by scmbbing. Scmbbing also removes any tars or heavy hydrocarbon fractions. Acid gases are removed by absorption in monoethanolamine, hot potassium carbonate, or by other patented removal processes. The purified gas stream is then sent to a carbon monoxide recovery section for final purification and by-product recovery. 

The second method used to reduce exliaust emissions incorporates postcombustion devices in the form of soot and/or ceramic catalytic converters. Some catalysts currently employ zeolite-based hydrocarbon-trapping materials acting as molecular sieves that can adsorb hydrocarbons at low temperatures and release them at high temperatures, when the catalyst operates with higher efficiency. Advances have been made in soot reduction through adoption of soot filters that chemically convert CO and unburned hydrocarbons into harmless CO, and water vapor, while trapping carbon particles in their ceramic honeycomb walls. Both soot filters and diesel catalysts remove more than 80 percent of carbon particulates from the exliatist, and reduce by more than 90 percent emissions of CO and hydrocarbons. 

Seawater studies require certified reference materials for biologically important dissolved components such as carbon (both inorganic and organic), nutrients, and trace metals, as well as for salinity, which is hydro-graphically important. A number of the committee s key recommendations therefore explicitly address these parameters. There is also a striking need for reference materials based on particulate matrices, where many of the analytical techniques used are matrix dependent and differ markedly... 

SO2, NOx, and total hydrocarbons. The mass spectrometric gas analysis is on a wet basis, as water vapor is not condensed out of the gas, while the analyzers at the sample port measure a gas stream dried using a permeation tube and refrigeration-type dryers in series. In addition to the measurements described above, surface temperature measurements of the boiler skin are made to estimate radiation losses, using the skin temperature, the room temperature and tabulated heat loss factors based on the temperature difference. Particulate mass emission rate and carbon content are measured for heat and mass balance purposes. At present, material deposited within the boiler during a test is collected but not factored into the heat or mass balances, because this deposition is considered to be negligible. Data taken are used to examine the heat balance for the 20-hp system. 

Carbon monoxide is first stripped off particulate matter in a cyclone separator or in a scrubber. Scrubbing also removes tar or heavy hydrocarbon fractions. Acidic gases, if present, are removed by absorption in monoethanol amine or in potassium carbonate. This pretreated gas is sent to the next section for further purification. Commercial processes for final purification are based on the absorption of carbon monoxide by salt solution, low-temperature condensation, or fractionation, or by pressure-swing adsorption using a solid material. 

---