Bromobenzenes

Bromobenzene,Cf,HfSr. B.p. 155°C. Prepared from benzene by direct bromination in the presence of a carrier (Ij, Fe, AICI3) or by... 

Ullman reaction The synthesis of diaryls by the condensation of aromatic halides with themselves or other aromatic halides, with the concomitant removal of halogens by a metal, e.g. copper powder thus bromobenzene gives diphenyl. The reaction may be extended to the preparation of diaryl ethers and diaryl thio-ethers by coupling a metal phenolate with an aryl halide. 

The method implies injection of a mixture of 3 radioactive tracers each being distributed into one of the 3 phases. The tracers must show such differences in the emitting y-radiation energy spectra that they can be simultaneously detected by on line y-spectrometry. Candidate tracers are Br-82 as bromobenzene for oil, Na-24 or La-140 for water, and Kr-85 for gas. The tracers are injected simultaneously at a constant rate into the flow in the pressurised pipe, and the concentration is detected as series of instantaneous measurements taken downstream as illustrated in figure 2. 

The tracer solution is made from oil soluble bromobenzene with the radioactive isotope Br-82. The tracer solution is injected through a thin nozzle inserted into the pipeline through the valve previously connected to the injection instrumentation. The injection device provides a very sharp beginning and termination of the fraction of labelled oil. 

Carefully refractionate the liquid of b.p. 150-160°, either by direct distillation from a small distilling-flask or (preferably) by using a short fractionating column, of the type shown in Fig. ii(b), p. 26. Almost pure bromobenzene is thus obtained, of... 

Bromobenzene is a colourless liquid of b.p. 156°, and d, 1 50 it has a faint agreeable odour. The bromine atom, being directly joined to the benzene ring, is very inert, and the only common reactions in which it is split off from the ring are the Fittig reaction (p. 288) and the Grignard reagent (pp. 280-284). 

When the addition of the bromobenzene is complete and the ether is boiling gently, reheat the flask on the water-bath for a further 15 minutes to ensure completion of the reaction the solution will now be slightly dark in colour, and only a trace of metallic magnesium should remain. 

Fit a 50 ml. round-bottomed flask to a reflux water-condenser fitted with a calcium chloride tube. Dissolve 1-05 ml. of dry bromobenzene in 5 ml. of dry ether and add this solution to 0-25 g. of magnesium contained in the round-bottomed flask. Now add a crystal of iodine so that it rests on the magnesium. Warm if necessary to start the reaction if the latter becomes too vigorous immerse the flask in cold... 

Methyl iodide, ethyl bromide and iodide, higher alpihatic halides chloroform, iodoform, carbon tetrachloride chlorobenzene, bromobenzene, iodobenzene benzyl chloride. 

Halogen, Chloral hydrate, sodium chloroacetate, chlorobenzene, />-chlorophenol, dichlorhydrin, bromobenzene, iodobenzene. 

Chlorobenzene, CjHjCl, bromobenzene, CgHgBr, and iodobenzene possess aromatic odours. Benzyl chloride, CgHjCHgCl, has a sharp irritating odour and is lachrymatory. 

Bromobenzene, iodobenzene and benzyl chloride behave somewhat similarly. The />-nitro-derivatives of the first two compounds frequently crystallise out even before pouring into water p-nitrobenzyl chloride usually remains as an oil for several minutes before solidifying. 

As an example of steam distillation, let us consider bromobenzene which has a normal boiling point of 155°. The vapour pressures of water and bromobenzene at different temperature.s are given in the following table. 

Thus for every 6 2 grams of water collectedinthereceiver 10 0 grams of bromobenzene are obtained (or the distillate contains 62 per cent, by weight of bromobenzene) in spite of the fact that bromobenzene has only 119/641 of the vapour pressm of water at the boiling point of the mixture. 

The following liquids may be used (boiling points are given in parentheses) — chlorobenzene (132-3°) bromobenzene (155°) p cymene (176°) o-dichloro-benzene (180°) aniline (184°) methyl benzoate (200°) teti-alin (207°) ethyl benzoate (212°) 1 2 4-trichlorobenzene (213°) iaopropyl benzoate (218°) methyl salicylate (223°) n-propyl benzoate (231°) diethyleneglycol (244°) n-butyl benzoate (250°) diphenyl (255°) diphenyl ether (259°) dimethyl phth ate (282°) diethyl phthalate (296°) diphenylamine (302°) benzophenone (305)° benzyl benzoate (316°). 

The fact that n-butylbenzene can be prepared in reasonable yield by the action of sodium upon a mixture of bromohenzene and n-butyl bromide can be partly explained on the assumption that n-butyl bromide reacts with phenyl-sodium more rapidly than does bromobenzene. It is interesting to note that n-butylbenzene can be prepared either from benzylsodium and n-propyl bromide or from phenylsodium and n-butyl bromide (Section VI,29). 

Nitration of bromobenzene with mixed acid yields largely p-bromo nitrobenzene accompanied by a little of the o-isomeride ... 

Method 1. Arrange the flask containing the reaction mixture for steam distillation as in Fig. II, 40, 1. Proceed with the steam distillation until crystals of p-dibromobenzene appear in the condenser. Change the receiver and continue with the distillation until all the p-dibromobenzeiie has passed over from time to time run out the water from the condenser so that the crystals melt and run down into the receiver. Reject the residue in the flask. Transfer the first distillate to a separatory funnel, wash it with a httle water, and dry the lower layer with a little anhydrous magnesium sulphate or anhydrous calcium chloride filter. Distil slowly from a small distilling flask use a wire gauze or an air bath (Fig. II, 5, 3). Collect the fraction which passes over at 150-170° pour the residue (R), while it is still hot, into a small beaker or porcelain basin for the isolation of p-dibromobenzene. Redistil the fraction of b.p. 150-170° and collect the bromobenzene at 154-157° (3). The yield is 60 g. 

Method 2. Transfer the dark-coloured reaction product to a separatory funnel and shake successively with water, with sufficient 5-10 per cent, sodium hydroxide solution to ensure that the washings are alkaline to litmus, and finally with water. Dry with anhydrous magnesium sulphate or calcium chloride. Filter through a fluted filter paper into a small distilling flask and distil slowly. Collect the crude bromobenzene at 150-170° pour the residue whilst still hot into a small porcelain basin. Redistil the hquid of b.p. 150-170° (3) and collect the bromobenzene at 154-157° the yield is about 60 g. 

The melting points of a number of sulphonacetamides are —benzene-sulphonic acid, 125° p-toluenesulphonic acid, 137° p-bromobenzene-sulphonic acid, 203° m-nitrobenzenesulphonic acid, 189° p-nitroben-zenesulphonic acid, 192° naphthalene-a-sulphonic acid, 185° and naphthalene-p-sulphonic acid, 146°. 

Propiophenone. Prepare a solution of diphenyl-cadmium in 110 ml. of dry benzene using 4 9 g. of magnesium, 32 4 g. of bromobenzene and 19 5 g. of anhydrous cadmium chloride. Cool the solution to 10°, and add during 3 minutes a solution of 14 -8 g. of propionyl chloride (b.p. 78-79°) in 30 ml. of dry benzene use external coohng with an ice bath to prevent the temperature from rising above 40°. Stir the mixture for 2 hours at 25-35°. Work up the product as detailed above except that 6 per cent, sodium carbonate solution should replace the saturated sodium bicarbonate solution. The yield of propiophenone, b.p. 100-102°/16 mm., is 17 6 g. 

---