Board support

In a gesso painting, a board support is layered with a plasterlike ground, the gesso, and a painting is made on this ground. 

An essential step in producing a credible Sustainability Report is to ensure that you have across-the-board support from senior management. This was not an issue at PotashCorp. The directive to publish a public document that reported on the Company s sustainable development initiatives had, in fact, come from senior management. 

TABLE 7.57 Deflection dynamics under a 100 lb load (a third-point load), a 5.5 in. X 1.25 in. Trex board, support span 22 in. 

After we had completed the system for NCI, the software was redesigned to run on an IBM Personal Computer which, by 1985, had available higher resolution graphics adapters, with the Hercules Graphics Board (Hercules Computer Technology, 2550 Ninth Street, Berkeley, CA 94710) being one of the most popular The Hercules board supported 720 horizontal by 348 vertical pixel resolution and... 

Board support Board sets expectations by asking for reports on improvement initiatives and results... 

In electronic systems, printed circuit boards are made from epoxy plastic and fibreglass. The nonconductive boards support layers of copper foil conductors. In electronic devices, the tiny and delicate active components are embedded within nonconductive epoxy or phenolic plastics, or within baked glass or ceramic coatings. 

The use of ARINC 653 meant that we were able to concentrate on the application logic. The platform supplier provided all the low-level software, including the Board Support Package (BSP) and the device drivers. 

A tooling plate with strategically located board supports should be created to hold the PCA during LGA stack assembly in order to minimize board flexure and to prevent damage to soldered parts on the PCA. 

Procedure. The test is conducted in a micro test tube fixed in an asbestos board support. A small amount of the sample or the evaporation residue firom a drop of the test solution is mixed with mercuriamide chloride or with a mixture of mercuric oxide and ammonium chloride. The open end of the test tube is covered with a disk of filter paper moistened with the reagent solution. The heating is begun at the upper end of the test tube and moved downward. A blue stain appears on the paper if the response is positive. 

To mill oval slabs, I use a modified end-board system. I usually prop up the log securely with a notched support and then mount a short end board to level at the upper end of the log. At the low er end, [ mount a longer board to level (1) These boards support the guide plank—tack it to the short end board w ith a couple of small nails (2), but leave the other end untacked to allow for mill exit. 

Block up a quarter so one split side is level and set up end boards, supporting lags and the guide plank. Mill off a slab. Then roll the log and level the remaining split side. Set end boards square to the milled surface and flatsavv or quartersaw the log. 

A powerful graphic controller driver and a dedicated BSP (Board Support Package) to make sure that a straightforward use of such multi-display applications is feasible. Graphic driver, optimized for Linux and T-Kemel OS (Operation Systems), are available for use. Support for fiuther automotive OS s are under discussion and will be accessible beginning of 2016. 

Fig. 3 Three versions of JTAG chain for FPGA configuration using the Platform Cable (upper), using the USB connection to PC application (middle) and using USB with extension board support (lower)...

Board Support Package Communication Based Train Control Central Command Terminal... 

Sufficient Board Support. Proper board support is essential to ensure consistent print results and higher yields. Without proper board support, the force applied to the board across the entire PCB width will vary, and proper gasketing between stencil and board will not be achieved. Blade angle also can be affected, causing paste to be left on the stencil. Board supports should be distributed evenly across the width of the board, particularly with BGA and fine-pitch components, to prevent bridging and inconsistent paste deposition. Board supports also should be kept dean to ensure good contact with the substrate and reduce contamination. 

FIG. 86 Reflow oven with shortened center board support spanning only the high temperature zones. (From Ref. 48.)... 

---