Block copolymer triblock

In this two-stage process, B is sequentially polymerized onto A, and then the two chains are coupled to yield an ABBA block copolymer. Triblocks of SBS have been prepared using this method, with methylene dichloride as the coupling agent. The disadvantage is the formation of radical anions, which can lead to contamination of the triblock with multiblock species. 

In this two-stage process, B is sequentially polymerized onto A, and then the two chains are coupled to yield an ABBA block copolymer. Triblocks of... 

Block copolymers consist of blocks of two or more different monomeric units. According to the number of blocks, a distinction is made, for example (with binary block copolymers), between two-block copolymers triblock copolymers and multiblock copolymers Multi-... 

Mural and co-workers [57] also optimised the mechanical properties of an rPP and recycled high impact polystyrene (rHIPS) blend at a composition of 70/30 wt%. Consequently, this composition was mixed with a styrene-ethylene-butylene-styrene (SEES) block copolymer triblock copolymer and Cloisite 20A OMMT. Using X-ray diffraction, the samples containing 3 wt% of nanoclay were found to lack the characteristic nanoclay peak, which indicated the mixed intercalated and exfoliated clay layers where the intercalated layers were further pushed toward the interphase [76]. The incorporation of a compatibiliser and nanoclay also improved the thermal stability of the PP/HIPS blend. SEES and nanoclay performed as an interfacial compatibiliser, which led to the reduction in particle size of rHIPS and the promotion of interfacial adhesion. 

Styrenic block copolymers (SBCs) are also widely used in HMA and PSA appHcations. Most hot melt appHed pressure sensitive adhesives are based on triblock copolymers consisting of SIS or SBS combinations (S = styrene, I = isoprene B = butadiene). Pressure sensitive adhesives typically employ low styrene, high molecular weight SIS polymers while hot melt adhesives usually use higher styrene, lower molecular weight SBCs. Resins compatible with the mid-block of an SBC improves tack properties those compatible with the end blocks control melt viscosity and temperature performance. 

Butadiene copolymers are mainly prepared to yield mbbers (see Styrene-butadiene rubber). Many commercially significant latex paints are based on styrene—butadiene copolymers (see Coatings Paint). In latex paint the weight ratio S B is usually 60 40 with high conversion. Most of the block copolymers prepared by anionic catalysts, eg, butyUithium, are also elastomers. However, some of these block copolymers are thermoplastic mbbers, which behave like cross-linked mbbers at room temperature but show regular thermoplastic flow at elevated temperatures (45,46). Diblock (styrene—butadiene (SB)) and triblock (styrene—butadiene—styrene (SBS)) copolymers are commercially available. Typically, they are blended with PS to achieve a desirable property, eg, improved clarity/flexibiHty (see Polymerblends) (46). These block copolymers represent a class of new and interesting polymeric materials (47,48). Of particular interest are their morphologies (49—52), solution properties (53,54), and mechanical behavior (55,56). 

Tbe system may be used for homopolymers and for block copolymers. Some commercial SBS triblock thermoplastic rubbers and the closely related K-resins produced by Phillips are of this type. Anionic polymerisation methods are of current interest in the preparation of certain diene rubbers. 

In Chapters 3 and 11 reference was made to thermoplastic elastomers of the triblock type. The most well known consist of a block of butadiene units joined at each end to a block of styrene units. At room temperature the styrene blocks congregate into glassy domains which act effectively to link the butadiene segments into a rubbery network. Above the Tg of the polystyrene these domains disappear and the polymer begins to flow like a thermoplastic. Because of the relatively low Tg of the short polystyrene blocks such rubbers have very limited heat resistance. Whilst in principle it may be possible to use end-blocks with a higher Tg an alternative approach is to use a block copolymer in which one of the blocks is capable of crystallisation and with a well above room temperature. Using what may be considered to be an extension of the chemical technology of poly(ethylene terephthalate) this approach has led to the availability of thermoplastic polyester elastomers (Hytrel—Du Pont Amitel—Akzo). 

Block copolymer chemistry and architecture is well described in polymer textbooks and monographs [40]. The block copolymers of PSA interest consist of anionically polymerized styrene-isoprene or styrene-butadiene diblocks usually terminating with a second styrene block to form an SIS or SBS triblock, or terminating at a central nucleus to form a radial or star polymer (SI) . Representative structures are shown in Fig. 5. For most PSA formulations the softer SIS is preferred over SBS. In many respects, SIS may be treated as a thermoplastic, thermoprocessible natural rubber with a somewhat higher modulus due to filler effect of the polystyrene fraction. Two longer reviews [41,42] of styrenic block copolymer PSAs have been published. 

The earliest SIS block copolymers used in PSAs were nominally 15 wt% styrene, with an overall molecular weight on the order of 200,000 Da. The preparation by living anionic polymerization starts with the formation of polystyryl lithium, followed by isoprene addition to form the diblock anion, which is then coupled with a difunctional agent, such as 1,2-dibromoethane to form the triblock (Fig. 5a, path i). Some diblock material is inherently present in the final polymer due to inefficient coupling. The diblock is compatible with the triblock and acts... 

Block copolymers can contain crystalline or amorphous hard blocks. Examples of crystalline block copolymers are polyurethanes (e.g. B.F. Goodrich s Estane line), polyether esters (e.g. Dupont s Hytrel polymers), polyether amides (e.g. Atofina s Pebax grades). Polyurethanes have enjoyed limited utility due to their relatively low thermal stability use temperatures must be kept below 275°F, due to the reversibility of the urethane linkage. Recently, polyurethanes with stability at 350°F for nearly 100 h have been claimed [2]. Polyether esters and polyether amides have been explored for PSA applications where their heat and plasticizer resistance is a benefit [3]. However, the high price of these materials and their multiblock architecture have limited their use. All of these crystalline block copolymers consist of multiblocks with relatively short, amorphous, polyether or polyester mid-blocks. Consequently they can not be diluted as extensively with tackifiers and diluents as styrenic triblock copolymers. Thereby it is more difficult to obtain strong, yet soft adhesives — the primary goals of adding rubber to hot melts. 

S-B-S Triblocks are block copolymers consisting of a block of butadiene units flanked by blocks of styrene. Below the T, of polystyrene blocks from different chains congregate into domains which act both as cross-links and reinforcing fillers. The jDolymers will dissolve in hydrocarbon solvents. Hydrogenated S-B-S materials have better resistance to ageing. 

The gel permeation chromatogram shown in Fig. 6 illustrates the purity of a block copolymer obtained by ion coupling. It is seen that about 5% of uncoupled block copolymer contaminates a triblock copolymer of narrow molecular weight distribution. The synthesis of star block polymers owes its recent development to the use of new coupling agents412. ... 

Somewhat limited work has been reported over the last decade. There are several reports on the synthesis and physical and structural characterization of styrene-dimethylsiloxane 141 144) and methylmethacrylate-dimethylsiloxane145> diblock, triblock and multiblock copolymers. Several reports are also available on the thermal223), solution 224,2251 and surface196 2261 characterization of various styrene-dimethyl-siloxane block copolymers synthesized by anionic techniques. 

Polystyrene-polytetrahydrofuran block copolymers121122 are an interesting case of coupling between functional polymers The mutual deactivation of living anionic polystyrene and living cationic polyoxolane occurs quantitatively to yield polystyrene-polyoxolane block copolymers. Since either of the initial polymer species can be mono- or difunctional, diblock, triblock or multiblock copolymers can be obtained. 

Vinyl copolymers contain mers from two or more vinyl monomers. Most common are random copolymers that are formed when the monomers polymerize simultaneously. They can be made by most polymerization mechanisms. Block copolymers are formed by reacting one monomer to completion and then replacing it with a different monomer that continues to add to the same polymer chain. The polymerization of a diblock copolymer stops at this point. Triblock and multiblock polymers continue the polymerization with additional monomer depletion and replenishment steps. The polymer chain must retain its ability to grow throughout the process. This is possible for a few polymerization mechanisms that give living polymers. 

Triblock copolymers of ABA type, where B is the central elastomeric block and A is the rigid end-block, are well-known commercially available polymers [7,8]. The chemical structures of some common TPEs based on styrenic block copolymers are given in Eigure 5.1. Synthesis of such ABA-type polymers can be achieved by three routes [9] ... 

Weiss et al. [75] have synthesized Na and Zn salt of sulfonated styrene(ethylene-co-butylene)-styrene triblock ionomer. The starting material is a hydrogenated triblock copolymer of styrene and butadiene with a rubber mid-block and PS end-blocks. After hydrogenation, the mid-block is converted to a random copolymer of ethylene and butylene. Ethyl sulfonate is used to sulfonate the block copolymer in 1,2-dichloroethane solution at 50°C using the procedure developed by Makowski et al. [76]. The sulfonic acid form of the functionalized polymer is recovered by steam stripping. The neutralization reaction is carried out in toluene-methanol solution using the appropriate metal hydroxide or acetate. 

The above equations gave reasonably reliable M value of SBS. Another approach to modeling the elastic behavior of SBS triblock copolymer has been developed [202]. The first one, the simple model, is obtained by a modification of classical rubber elasticity theory to account for the filler effect of the domain. The major objection was the simple application of mbber elasticity theory to block copolymers without considering the effect of the domain on the distribution function of the mbber matrix chain. In the derivation of classical equation of rabber elasticity, it is assumed that the chain has Gaussian distribution function. The use of this distribution function considers that aU spaces are accessible to a given chain. However, that is not the case of TPEs because the domain also takes up space in block copolymers. 

---