Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Block copolymer step polymerization

Block copolymers are synthesized by a variety of methods (45,46) most important are sequential polymeriza tion and step growth. In sequential polymerization, a polymer (A) is first synthesized in such a way that it contains at least one group per molecule that can initiate polymerization of another monomer B. [Pg.14]

Block copolymer—These copolymers are built of chemically dissimilar terminally connected segments. Block copolymers are generally prepared by sequential anionic addition or ring opening or step growth polymerization. [Pg.481]

Macroinitiators are macromolecules having peroxygen and/or azo groups that can thermally initiate a vinyl polymerization to obtain block copolymers in one step. They can be classified as macroperoxyinitiators (MPl), macroazoinitiators (MAI), and macroazo-peroxyiniti-ators. [Pg.726]

In a third type of block copolymer formation. Scheme (3), the initiator s azo group is decomposed in the presence of monomer A in a first step. The polymer formed contains active sites different from azo functions. These sites may, after a necessary activation step, start the polymerization of the second monomer B. Actually, route (3) of block copolymer formation is a vice versa version of type (1). It has been shown in a number of examples that one starting bifunctional azo compound can be used for block copolymer synthesis following either path. Reactions of type (3) are tackled in detail in Section III of this chapter. [Pg.736]

Low-molecular weight azo compounds have frequently been used in cationic polymerizations producing azo-containing polymers. Thus, the combination of ionically and radically polymerizable monomers into block copolymers has been achieved. Azo compounds were used in all steps of cationic polymerization without any loss of azo function as initiators, as monomers and, finally, as terminating agents. [Pg.741]

Hepuzer et al. [91] have used the photoinduced homolytical bond scission of ACPB to produce styrene-based MAIs. These compounds were in a second thermally induced polymerization transferred into styrene-methacrylate block copolymers. However, as Scheme 24 implies, benzoin radicals are formed upon photolysis. In the subsequent polymerization they will react with monomer yielding nonazofunctionalized polymer. The relatively high amount of homopolymer has to be separated from the block copolymer formed after the second, thermally induced polymerization step. [Pg.746]

Generation of radicals by redox reactions has also been applied for synthesizing block copolymers. As was mentioned in Section II. D. (see Scheme 23), Ce(IV) is able to form radical sites in hydroxyl-terminated compounds. Thus, Erim et al. [116] produced a hydroxyl-terminated poly(acrylamid) by thermal polymerization using 4,4-azobis(4-cyano pentanol). The polymer formed was in a second step treated with ceric (IV) ammonium nitrate, hence generating oxygen centered radicals capable of starting a second free radical polymeriza-... [Pg.751]

Preparation and characteristics of ABA type polycaprolactone-b-polydimethyl-siloxane block copolymers have been recently reported 289). In this study, ring-opening polymerization of e-caprolactone was achieved in melt, using a hydroxybutyl terminated PSX as the initiator and a catalytic amount of stannous octoate. Reactions were completed in two steps as shown in Reaction Scheme XIX. [Pg.51]

Vinyl copolymers contain mers from two or more vinyl monomers. Most common are random copolymers that are formed when the monomers polymerize simultaneously. They can be made by most polymerization mechanisms. Block copolymers are formed by reacting one monomer to completion and then replacing it with a different monomer that continues to add to the same polymer chain. The polymerization of a diblock copolymer stops at this point. Triblock and multiblock polymers continue the polymerization with additional monomer depletion and replenishment steps. The polymer chain must retain its ability to grow throughout the process. This is possible for a few polymerization mechanisms that give living polymers. [Pg.470]

Though living anionic polymerization is the most widely used technique for synthesizing many commercially available TPEs based on styrenic block copolymers, living carbocationic polymerization has also been developed in recent years for such purposes [10,11], Polyisobutylene (PlB)-based TPEs, one of the most recently developed classes, are synthesized by living carbocationic polymerization with sequential monomer addition and consists of two basic steps [10] as follows ... [Pg.107]

The transformation of the chain end active center from one type to another is usually achieved through the successful and efficient end-functionalization reaction of the polymer chain. This end-functionalized polymer can be considered as a macroinitiator capable of initiating the polymerization of another monomer by a different synthetic method. Using a semitelechelic macroinitiator an AB block copolymer is obtained, while with a telechelic macroinitiator an ABA triblock copolymer is provided. The key step of this methodology relies on the success of the transformation reaction. The functionalization process must be 100% efficient, since the presence of unfunctionalized chains leads to a mixture of the desired block copolymer and the unfunctionalized homopolymer. In such a case, control over the molecular characteristics cannot be obtained and an additional purification step is needed. [Pg.62]

For the hydrosilylation reaction various rhodium, platinum, and cobalt catalysts were employed. For the further chain extension the OH-functionalities were deprotected by KCN in methanol. The final step involved the enzymatic polymerization from the maltoheptaose-modified polystyrene using a-D-glucose-l-phosphalc dipotassium salt dihydrate in a citrate buffer (pH = 6.2) and potato phosphorylase (Scheme 59). The characterization of the block copolymers was problematic in the case of high amylose contents, due to the insolubility of the copolymers in THF. [Pg.72]

An interesting development regarding the synthesis of block copolymers involves the use of bifunctional or dual initiators, which are compounds capable of performing two mechanistically distinct polymerizations. The advantage of this procedure is that there is no need for intermediate transformation or activation steps. If the different initiation sites are equally active for the... [Pg.72]

Until quite recently, the best known answer to the challenge of combining different properties in an additive manner in a single polymeric product, has been the use of so-called "living" initiators to produce block copolymers, in a 2- or 3-steps process depending wether a di- or a tri-blockwas needed, (see scheme I). [Pg.308]

We have shown that polymeric micelles constmcted of block copolymers of poly(ethylene oxide) (PEG) and poly(L-asparate) containing the anticancer dmg (adriamycin, ADR) selectively accumulate at solid tumor sites by a passive targeting mechanism. This is likely due to the hydrophilicity of the outer PEG chains and micellar size (<100 nm) that allow selective tissue interactions [17,18]. Polymeric micelle size ranges are tailored during polymer synthesis steps. Carefully selection of block polymer chemistry and block lengths can produce micelles that inhibit nonselective scavenging by the reticuloendothelial system (RES) and can be utilized as targetable dmg... [Pg.28]

In this method, a reactive group on the surface initiates the polymerization, and the propagating polymer chain grows from the surface (Fig. 9.19b). In principle, it can be employed with all polymerization types, and a number of papers have reported high amounts of immobihzed polymer using surface-initiated polymerization with various initiator/monomer systems. If controlled or Hving polymerization techniques are used, block copolymer or end-functionahzed polymer brush systems can be prepared in consecutive reaction steps (Fig. 9.19c). [Pg.401]


See other pages where Block copolymer step polymerization is mentioned: [Pg.149]    [Pg.149]    [Pg.6]    [Pg.236]    [Pg.189]    [Pg.189]    [Pg.748]    [Pg.748]    [Pg.751]    [Pg.755]    [Pg.759]    [Pg.759]    [Pg.451]    [Pg.20]    [Pg.26]    [Pg.225]    [Pg.4]    [Pg.154]    [Pg.59]    [Pg.30]    [Pg.88]    [Pg.63]    [Pg.78]    [Pg.144]    [Pg.92]    [Pg.96]    [Pg.89]    [Pg.108]    [Pg.12]    [Pg.160]    [Pg.170]    [Pg.178]    [Pg.189]    [Pg.664]    [Pg.95]    [Pg.19]   
See also in sourсe #XX -- [ Pg.136 , Pg.139 , Pg.142 ]

See also in sourсe #XX -- [ Pg.136 , Pg.139 , Pg.142 ]




SEARCH



Block copolymer polymerization

Block copolymers step-growth polymerization

Polymerization copolymers

Step polymerization

© 2024 chempedia.info