Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Bed height

Fig. 22. Performance cut diameter predictions for typical dry packed bed particle collectors as a function of bed height or depth, packing diameter and packing porosity (void area) S. Bed irrigation increases collection efficiency or decreases cut diameter (271). SoHd lines, = 25 mm dashed lines,... Fig. 22. Performance cut diameter predictions for typical dry packed bed particle collectors as a function of bed height or depth, packing diameter and packing porosity (void area) S. Bed irrigation increases collection efficiency or decreases cut diameter (271). SoHd lines, = 25 mm dashed lines,...
The sohd can be contacted with the solvent in a number of different ways but traditionally that part of the solvent retained by the sohd is referred to as the underflow or holdup, whereas the sohd-free solute-laden solvent separated from the sohd after extraction is called the overflow. The holdup of bound hquor plays a vital role in the estimation of separation performance. In practice both static and dynamic holdup are measured in a process study, other parameters of importance being the relationship of holdup to drainage time and percolation rate. The results of such studies permit conclusions to be drawn about the feasibihty of extraction by percolation, the holdup of different bed heights of material prepared for extraction, and the relationship between solute content of the hquor and holdup. If the percolation rate is very low (in the case of oilseeds a minimum percolation rate of 3 x 10 m/s is normally required), extraction by immersion may be more effective. Percolation rate measurements and the methods of utilizing the data have been reported (8,9) these indicate that the effect of solute concentration on holdup plays an important part in determining the solute concentration in the hquor leaving the extractor. [Pg.88]

A generic multipurpose fluidized bed is illustrated in Figure 2 (1). The soHds are contained in a vessel and gas is introduced into the system via a distributor, which is typically a drilled plate at the bottom of the vessel. A plenum chamber is provided below the distributor plate. The height of the soHds level above the distributor is called the bed height, and the vertical space above the bed height is called the freeboard. A splash zone may exist as a transition between the bed and freeboard. Cyclones, located either in the freeboard or external to the vessel, are used to remove soHds from the gas stream. Diplegs can return entrained soHds directly to the bed. [Pg.69]

This equation predicts that the height of a theoretical diffusion stage increases, ie, mass-transfer resistance increases, both with bed height and bed diameter. The diffusion resistance for Group B particles where the maximum stable bubble size and the bed height are critical parameters may also be calculated (21). [Pg.77]

Normally vessels are designed with the gas outlet location well above TDH. If circumstances force operation with a bed height so that the outlet is below TDH, an equivalent velocity, an effective velocity higher than the actual superficial gas velocity, is used ia the above calculation. The effective gas velocity can be determined from Figure 19 (27). [Pg.80]

These design fundamentals result in the requirement that space velocity, effective space—time, fraction of bubble gas exchanged with the emulsion gas, bubble residence time, bed expansion relative to settled bed height, and length-to-diameter ratio be held constant. Effective space—time, the product of bubble residence time and fraction of bubble gas exchanged, accounts for the reduction in gas residence time because of the rapid ascent of bubbles, and thereby for the lower conversions compared with a fixed bed with equal gas flow rates and catalyst weights. [Pg.518]

Reactor design for glucose isomerization ia the United States has been documented (75). The diameter of the reactor is normally between 0.6 and 1.5 m. Typical bed height is 2—5 m. The ratio between the bed height and diameter of a reactor should be at least 3 1 to ensure good flow distribution. Plants that produce more than 1000 t of HECS per day, based on dry matter, use at least 20 separate reactors. [Pg.298]

Calculate the required packed bed height by Eq. (14-169). Behavior of Various Systems and Pacldngs For orientation... [Pg.1398]

FIG. 14-72 HETP values for four sizes of metal pall rings, vacuum operation. Cyclobexane/n-beptane system, total reflux,. 35 kPa (5.0 psia). Column diameter = 1.2 m (4.0 ft). Bed height = 3.7 m (12 ft). Distributor = tubed drip pan, 100 streams/nv. [Adapted from Shafiat and Kunesh, Ind. Eng. Cbem. Res., 34,1273 (1.9.9.5),] Reproduced with permission. Copyright 1995 American Chemical Society. [Pg.1399]

FIG. 14-74 HETP values for Max-Pak structured packing,. 35 kPa (5 psia), two column diameters. Cyclohexane/n-heptane system, total reflux. For 0.4.3 m (1.4 ft) column perforated pipe distributor, 400 streams/m2, 3.05 m (10 ft) bed height. For 1.2 m (4.0 ft) column tubed drip pan distributor, 100 streams/m ,. 3.7 m (12 ft) bed height. Smaller column data. University of Texas/Austin Larger column data. Fractionation Research, Inc. To convert (ft/s)(lb/ft ) to (m/s)(kg/m ) , multiply by 1.2199. (Couiiesy Jaeger Troducts, Inc., Housion, Texas.)... [Pg.1400]

Bed Bed height is determined by a number of factors, either individually or collec tively, such as ... [Pg.1563]

Packed bed heights typically vary from 20 ft to 30ft. Many times the location of manholes to provide access to the redistributor will determine the packed depth. Whenever more than 15 theoretical stages are required in one packed bed, good liquid distribution is critical. ... [Pg.84]

Next, to determine packed column height use Table 9 for distillation HETP values, leaning tow ards the high side of the range for studies. For use of Kqa values see Section A—Absorbers. Bed height per packed bed runs up to 20-30 ft for metal or ceramic packings, but plastic packing is usually limited to 24 ft. [Pg.85]

The fraction q can be expressed in terms of the expanded bed height H and minimum fluidization height H , and terms may be substituted for U -... [Pg.33]

Equation 8 has not been rigorously tested on freely bubbling beds because of the difficulty of making precise independent measurements of Dg or Ug under such conditions. It has been verified for slugging beds, however, as is shown in Figure 3. In the case of slugging, the surface level of the bed oscillates considerably, and in this case, the maximum bed height is used for H in Equation 8. [Pg.33]


See other pages where Bed height is mentioned: [Pg.297]    [Pg.297]    [Pg.410]    [Pg.92]    [Pg.76]    [Pg.77]    [Pg.83]    [Pg.84]    [Pg.84]    [Pg.518]    [Pg.527]    [Pg.171]    [Pg.1223]    [Pg.1394]    [Pg.1395]    [Pg.1401]    [Pg.1563]    [Pg.1571]    [Pg.1821]    [Pg.1887]    [Pg.1888]    [Pg.1888]    [Pg.1897]    [Pg.1897]    [Pg.2119]    [Pg.2126]    [Pg.147]    [Pg.94]    [Pg.312]    [Pg.269]    [Pg.271]    [Pg.480]    [Pg.33]    [Pg.44]   
See also in sourсe #XX -- [ Pg.33 ]

See also in sourсe #XX -- [ Pg.163 , Pg.466 ]

See also in sourсe #XX -- [ Pg.434 , Pg.463 ]




SEARCH



Effect of static bed height

Height of bed

Maximum bed height

Static bed height

© 2026 chempedia.info