Aqueous solubility chemistry control

Aqueous solubility, potency and permeability are three factors under medicinal chemistry control that must be optimized to achieve a compound with acceptable oral absorption. Typically, a lead (chemistry starting point) is deficient in all three parameters. The inter-relationships of these three parameters has been described in a series of publications from Pfizer researchers [7, 8]. Figure 9.1 depicts graphically the minimum acceptable solubility as a function of projected clinical potency and intestinal permeability. A minimum thermodynamic aqueous solubility of 52... 

The hydrated cation Ca2+aq is of prime importance to the aqueous solution chemistry of calcium, and to most of its various roles in biological systems. The relation between lattice energy and hydration energies of the constituent ions determine solubilities, the size of the hydrated cation controls selectivity and the passage of ions through channels, and the work required to remove some or all of the water of hydration is relevant both to... 

Positive-Tone Photoresists based on Dissolution Inhibition by Diazonaphthoquinones. The intrinsic limitations of bis-azide—cyclized rubber resist systems led the semiconductor industry to shift to a class of imaging materials based on diazonaphthoquinone (DNQ) photosensitizers. Both the chemistry and the imaging mechanism of these resists (Fig. 10) differ in fundamental ways from those described thus far (23). The DNQ acts as a dissolution inhibitor for the matrix resin, a low molecular weight condensation product of formaldehyde and cresol isomers known as novolac (24). The phenolic structure renders the novolac polymer weakly acidic, and readily soluble in aqueous alkaline solutions. In admixture with an appropriate DNQ the polymer s dissolution rate is sharply decreased. Photolysis causes the DNQ to undergo a multistep reaction sequence, ultimately forming a base-soluble carboxylic acid which does not inhibit film dissolution. Immersion of a pattemwise-exposed film of the resist in an aqueous solution of hydroxide ion leads to rapid dissolution of the exposed areas and only very slow dissolution of unexposed regions. In contrast with crosslinking resists, the film solubility is controlled by chemical and polarity differences rather than molecular size. 

The large S02 mass accommodation coefficient (7 - 0.11) indicates that interfacial mass transport will not limit the rate of S02 uptake into clean aqueous cloud and fog droplets. Either gas phase diffusion, Henry s law solubility, or aqueous reactivity will control the overall rate of aqueous S(IV) chemistry. This conclusion is demonstrated by modeling studies of S02 oxidation in clouds by Chamedies (3) showing that the conversion time of S(FV) to S(IV) is independent of the mass accommodation coefficient for 1 7 > 10 2 Schwartz (1 ) has also shown that, with 7 as large as our measured value, the interfacial mass transport is unlikely to inhibit the oxidation of SC by or Ho02 in cloud droplets for gas concentrations typical of non-urban industrialized regions. 

Chemistry control of aqueous solubility is poor because, except for a few very specific exceptions, chemistry SAR is blunt. In this respect, control of solubility like that of permeability is poor. Solubility due to excessive lipophilicity... 

Chemistry control of aqueous solubility is poor. The good news is that if a compound has poor aqueous solubility, methods do exist to fix the problem... 

Table 13 shows some of the developmental products that have EPA appHcations pending and may be available in the near future. Sea Nine is a variation on the very successflil isothiazolone chemistry. It is claimed to be an improvement over metallic actives used for antifouling paint and wood preservation (46,47). Decylthioethylamine and its water-soluble hydrochloride are claimed to be especially effective at controlling biofilm in cooling water appHcations (48—50). The hydroxymethylpyra2ole shown is also suggested to have properties that are well suited to the protection of aqueous products or emulsions (51,52). 

The first example of microwave-promoted solid-phase methodology in heterocyclic chemistry was the arylation of thiophene and indole via Suzuki couplings on TentaGel S RAM resin, as demonstrated by Hallberg and coworkers in 1996, before temperature- and pressure-controlled microwave instruments were even available [189]. Three years later Schotten and coworkers presented analogous but aqueous Suzuki couplings of 5-bromo-thiophene anchored to PEG soluble support via a carboxylic function at its C-2 position [116]. Unfortunately, this work was performed in a do-... 

The solubility of contaminants in subsurface water is controlled by (1) the molecular properties of the contaminant, (2) the porous media solid phase composition, and (3) the chemistry of the aqueous solution. The presence of potential cosolvents or other chemicals in water also affects contaminant solubility. A number of relevant examples selected from the literature are presented here to illustrate various solubility and dissolution processes. 

---