Adsorbed onto polystyrene

Polymers can also be used for the physical immobilization of metal complexes. For example, the degree of swelling observed for 1% crosslinked polystyrene varies with solvents more swelling is observed in THF than in methanol. Thus, the cationic complex [(diphos)Rh(NBD)]PF6 can be adsorbed onto polystyrene in THF. When dried and extracted with methanol, the complex is bound within the polystyrene matrix. The immobilized complex is a catalyst for the hydrogenation of 1-hexene in methanol. ... 

FIG. 1 Amount of sodium dodecyl sulfate adsorbed onto polystyrene latex surfaces as a function of surface charge density. ( ) Hoeft [44] o) Ali et al. [34] (O) Hoeft and Zollars [35] (A) Brouwer and Zsom [36] ) Gwin [37]. 

Proteins adsorbed onto polystyrene latex particles have proved to be good models for the interfacial behavior of proteins in processed foods. The behavior of caseins on latex particles appears to be veiy similar to that at the oil/water interfaces of emulsions, at the air/water interface of foams, and at the surface of casein micelles. 

The second technique of choice is SANS. Small angle neutron scattering is a classical tool for studying separately. polymeric and colloidal systems. As first shown by Cosgrove et al. it can also be used to observe polymers at interfaces. These authors were able to measure for the first time the concentration profile of poly(oxyethylene) chains adsorbed onto polystyrene colloidal grains. Their data were in qualitative agreement with the train-loop-tail description of Scheutjens... 

Fig. XI-7. Volume fraction profile of 280,000-molecular-weight poly(ethylene oxide) adsorbed onto deuterated polystyrene latex at a surface density of 1.21 mg/m and suspended in D2O, from Ref. 70.

Experimental investigations of the model system of dye molecules adsorbed onto surfaces of polystyrene spheres have finuly established the sensitivity and surface specificity of the SHG method even for particles of micrometre size [117]. The surface sensitivity of die SHG process has been exploited for probing molecular transport across the bilayer in liposomes [118], for measurement of electrostatic potentials at the surface of small particles [119] and for imaging... 

In the earlier literature on steric stabilization there was a tendency to ignore the importance of anchoring sites for steric stabilizers. Without strong anchors the adsorbed molecules are easily swept aside in collisions, as has been so well illustrated with polystyrene adsorbed onto carbon blacks in hydrocarbon solutions in these systems particles flocculate in every collision.(11)... 

Liu and Rauch (2003) of Motorola investigated oligonucleotide probe attachment onto polystyrene (PS), polycarbonate (PC), polymethyl methacrylate (PMMA), and polypropylene (PP) plastic surfaces. They utilized three different immobilization processes SurModics surface modification solution (that allows attachment of adsorbed reactive groups to a surface by photoactivation of polymers at 254 nm). Pierce Reactive-Bind coating solution, and CTAB (cetyltrimethylammonium bromide, a cationic detergent). Not surprisingly, the microarray performances on these plastics varied. 

Abstract Pressure-sensitive paint (PSP) is applied to the areodynamics measurement. PSP is optical sensor based on the luminescence of dye probe molecules quenching by oxygen gas. Many PSPs are composed of probe dye molecules, such as polycyclic aromatic hydrocarbons (pyrene, pyrene derivative etc.), transition metal complexes (ruthenium(II), osumium(II), iridium(III) etc.), and metalloporphyrins (platinum (II), palladium(II), etc.) immobilized in oxygen permeable polymer (silicone, polystyrene, fluorinated polymer, cellulose derivative, etc.) film. Dye probe molecules adsorbed layer based PSPs such as pyrene derivative and porphyrins directly adsorbed onto anodic oxidised aluminium plat substrate also developed. In this section the properties of various oxygen permeable polymer for matrix and various dye probes for PSP are described. 

Adsorption of block copolymers onto a surface is another pathway for surface functionalization. Block copolymers in solution of selective solvent afford the possibility to both self-assemble and adsorb onto a surface. The adsorption behavior is governed mostly by the interaction between the polymers and the solvent, but also by the size and the conformation of the polymer chains and by the interfacial contact energy of the polymer chains with the substrate [115-119], Indeed, in a selective solvent, one of the blocks is in a good solvent it swells and does not adsorb to the surface while the other block, which is in a poor solvent, will adsorb strongly to the surface to minimize its contact with the solvent. There have been a considerable number of studies dedicated to the adsorption of block copolymers to flat or curved surfaces, including adsorption of poly(/cr/-butylstyrcnc)-ft/od -sodium poly(styrenesulfonate) onto silica surfaces [120], polystyrene-Woc -poly(acrylic acid) onto weak polyelectrolyte multilayer surfaces [121], polyethylene-Wocfc-poly(ethylene oxide) on alkanethiol-patterned gold surfaces [122], or poly(ethylene oxide)-Woc -poly(lactide) onto colloidal polystyrene particles [123],... 

NIL patterns were also used for the assembly of nanoparticles via supramole-cular host-guest interactions.95 The NIL-patterned substrate was functionalized with CD SAMs via a three-step synthesis process. The fabrication of 3D nanostructures was achieved by the alternating assembly of multivalent guest-functionalized dendrimers and CD-fnnctionalized Au nanoparticles.88 This methodology can be applied to various nanoparticles, regardless of their size and core material. For instance, CD-functionalized silica and polystyrene nanoparticles were adsorbed onto NIL-patterned CD SAMs with preadsorbed guest-fnnctionalized dendrimers.60 92 Recently, Huskens et al. demonstrated the supramolecular LbL assembly of 3D multicomponent nanostructures of nanoparticles by alternating assembly steps of complementary ferrocenyl-functionalized silica nanoparticles and different kinds of host-fnnctionalized nanoparticles (see Fig. 13.8).66... 

Much of the early studies of surfactant adsorption at the solid-solution interface were based on classical experimental techniques, such as solution depletion [1, 32], fluorescence spectroscopy [2], and measurements of the differential enthalpy of adsorption [2], Such methods have provided much of the basic initial understanding. However, they provide no direct structural information and are difficult to apply to mixtures [23, 34], However, when combined with other techniques, such as NMR and flow microcalorimetry, they provide some insight into the behaviour of mixtures. This was demonstrated by Thibaut et al. [33] on SDS/C10E5 mixtures adsorbed onto silica and by Colombie et al. [34] on the adsorption of SLS/Triton X-405 mixtures onto polystyrene particles. 

Polymer microspheres with monodispersed distribution in size are much perferable for phagocytosis assays, because the size dominantly governs phagocytosis of the microspheres by M< ). In addition, the microspheres should be prepared without any surfactants to exclude the influence of the soap molecules adsorbed onto the surface, on phagocytosis of the microspheres. We have synthesized monodispersed polystyrene microspheres by soap-free emulsion polymerization of styrene at 70 °C for 30 hr using potassium persulfate as a initiator [14]. The widely different diameters of the... 

In a few studies sonochemistry was used to coat polymers with nanosized par-tides [48-50]. Of these three reports one [50] dealt with metals, more specifically with noble metals (Pt, Pd, and Au). In this research, metal colloids are adsorbed to the surface of neutral functionalized polystyrene microspheres, PSMS. The authors report on the synthesis and characterization of catalytically important noble monometallic colloids using various chemical and sonochemical methods. These metal colloids are then adsorbed onto suitably functionalized PSMS. The metal-immobilized microspheres are reacted with a linker such as 4-mercaptobutyl phosphonic acid and subsequently used to grow multilayers. 

---