Acrylonitrile/ methylacrylate

The simplest monomer, ethylenesulfonic acid, is made by elimination from sodium hydroxyethyl sulfonate and polyphosphoric acid. Ethylenesulfonic acid is readily polymerized alone or can be incorporated as a copolymer using such monomers as acrylamide, aHyl acrylamide, sodium acrylate, acrylonitrile, methylacrylic acid, and vinyl acetate (222). Styrene and isobutene fail to copolymerize with ethylene sulfonic acid. 

The compound (dppe)PtMe(OMe),256 which is prepared by a metathesis reaction involving NaOMe and (dppe)PtMe(Cl) in a mixed benzene/methanol solvent system (dppe = bis(l,2-di-phenylphosphino)ethane), does not react with ethylene or pentene but does react with activated alkenes such as acrylonitrile, methylacrylate and fluoroalkenes. The reaction involving tetrafluoro-ethylene has been shown to give (dppe)PtMe(CF2CF2OMe), providing the first example of an alkene insertion into an M—OR bond.256 Interestingly, no insertion into the Pt—Me bond was observed. 

Yuguchi, S., and M. Watanabe Copolymerisation of acrylonitrile, methylacrylate and 2-vinylpyridine ternary system. Chem. High Polymers (Tokyo) 17, 465 (1960). 

Antoine et al. [17] reported that a terpolymer of acrylonitrile, methylacrylate, and butadiene was bioconvmied by a strain of either Nocardia or Penicillium [17]. They found ffiat, after 6 months of incubation, the terpolymer was transformed into both a lower molecular weight... 

Table 7.16 contains the copolymerisation parameters of acrylonitrile-methylacrylate copolymers containing between 0.36 and 0.88 mole fraction of acrylonitrile (i.e., F ) for various monomer feed ratios and indicate that a knowledge of mole fractions (F) and reactivity ratios (r) enables prediction to be made, not only of average mole ratios but also of average number of sequences of monomer units per length of polymer and the average sequence length of each monomer. 

Table 7.16 Copolymerisation parameters of acrylonitrile-methylacrylate copolymers determined by C-NMR spectroscopy ...

The principal monomer of nitrile resins is acrylonitrile (see Polyacrylonitrile ), which constitutes about 70% by weight of the polymer and provides the polymer with good gas barrier and chemical resistance properties. The remainder of the polymer is 20 to 30% methylacrylate (or styrene), with 0 to 10% butadiene to serve as an impact-modifying termonomer. 

Acryhc stmctural adhesives have been modified by elastomers in order to obtain a phase-separated, toughened system. A significant contribution in this technology has been made in which acryhc adhesives were modified by the addition of chlorosulfonated polyethylene to obtain a phase-separated stmctural adhesive (11). Such adhesives also contain methyl methacrylate, glacial methacrylic acid, and cross-linkers such as ethylene glycol dimethacrylate [97-90-5]. The polymerization initiation system, which includes cumene hydroperoxide, N,1S7-dimethyl- -toluidine, and saccharin, can be apphed to the adherend surface as a primer, or it can be formulated as the second part of a two-part adhesive. Modification of cyanoacrylates using elastomers has also been attempted copolymers of acrylonitrile, butadiene, and styrene ethylene copolymers with methylacrylate or copolymers of methacrylates with butadiene and styrene have been used. However, because of the extreme reactivity of the monomer, modification of cyanoacrylate adhesives is very difficult and material purity is essential in order to be able to modify the cyanoacrylate without causing premature reaction. 

Besides the MBS materials, related terpolymers have been prepared. These include materials prepared by terpolymerising methyl methacrylate, acrylonitrile and styrene in the presence of polybutadiene (Toyolac, Hamano 500) methyl methacrylate, acrylonitrile and styrene in the presence of a butadiene-methyl methacrylate copolymer (XT Resin), and methylacrylate, styrene and acrylonitrile on to a butadiene-styrene copolymer. 

The ratio of the two diastereomeric products 190 and 191 was found to depend on the reaction temperature and reaction time. The addition of acrolein or methyl vinyl ketone proceeded smoothly, but in the case of methylacrylate or acrylonitrile the reaction did not proceed under the same conditions (EtsN THF 30°C). An accompanying AMI calculation of these Q ,/3-unsaturated compounds [LUMOs for acrolein, -0.13877 for methyl vinyl ketone, -0.06805 (s-trans) for methyl acrylate, -0.01413 (s-tmns) for acrylonitrile, 0.04971] suggested the low reactivity of methyl acrylate and acrylonitrile toward the Michael reaction (99H1321). 

Two different emulsion polymerization reactions were Investigated. One was the polymerization of acrylonitrile and methylacrylate (75/25 AN/MA) In the presence of an acrylonitrile elastomer (70/30 BD/AN) to produce a graft resin, llie second was the copolymerization oiE acrylonitrile and styrene (70/30 AN/S). Chromatographic analyses of latex solutions were conducted periodically during both types of polymerization reactions, using acetonitrile as latex solvent and chromatographic mobile phase. 

Unreacted monomers In AN/M latex solutions were measured similarly. Methylacrylate Is a relatively strong UV absorber In the 225-250 nm range while acrylonitrile does not significantly absorb UV radiation at wavelengths above about 220 nm. At 230 nm, the wavelength used, the UV detector responded only to methylacrylate. And the refractive Indices of the two monomers are such that. In the 75/25 AN/MA proportions used, the refrac-tometer was Insensitive to methylacrylate. The reiErac tome ter therefore functioned as a selective detector for acrylonitrile In the presence of methylacrylate. 

Similarly, estimation of chemical composition of soluble polymer was also dependent on selectivity of the UV detector. Polymerized acrylonitrile has no significant UV absorbance at 230 and 254 nm. Thus, UV chromatograms were used to estimate amounts of polymerized methylacrylate and styrene In each resin system. The refractometer detector was sensitive to polymerized methylacrylate and styrene, as well as to polymerized acrylonitrile. It was therefore necessary to calculate comonomer contribution to refractometer peak areas In order to estimate concentration of polymerized acrylonitrile. This was done by obtaining a refractometer calibration for all three homopolymers. Quantity of polymerized comonomers measured by UV were then converted to equivalent refractometer peak areas. Peak areas due to polymerized acrylonitrile were then calculated by difference, and used to calculate amount of polymerized acrylonitrile. 

The results of the olefin oxidation catalyzed by 19, 57, and 59-62 are summarized in Tables VI-VIII. Table VI shows that linear terminal olefins are selectively oxidized to 2-ketones, whereas cyclic olefins (cyclohexene and norbomene) are selectively oxidized to epoxides. Cyclopentene shows exceptional behavior, it is oxidized exclusively to cyclopentanone without any production of epoxypentane. This exception would be brought about by the more restrained and planar pen-tene ring, compared with other larger cyclic nonplanar olefins in Table VI, but the exact reason is not yet known. Linear inner olefin, 2-octene, is oxidized to both 2- and 3-octanones. 2-Methyl-2-butene is oxidized to 3-methyl-2-butanone, while ethyl vinyl ether is oxidized to acetaldehyde and ethyl alcohol. These products were identified by NMR, but could not be quantitatively determined because of the existence of overlapping small peaks in the GC chart. The last reaction corresponds to oxidative hydrolysis of ethyl vinyl ether. Those olefins having bulky (a-methylstyrene, j8-methylstyrene, and allylbenzene) or electon-withdrawing substituents (1-bromo-l-propene, 1-chloro-l-pro-pene, fumalonitrile, acrylonitrile, and methylacrylate) are not oxidized. 

Poly(methyl methacrylate) Vinyl chloride Acrylonitrile Ethylene Acrylic add Methylacrylate Acrylonitrile Styrene Butylene dimethacrylate Acrylic add... 

Polybutylene dimethacrylate Ethylene Acrylic acid Methylacrylate Acrylonitrile Styrene Butylene dimethacrylate... 

Was used in prepn of acrylate resins and of other copolymers and polymers. Acrylate resins are thermoplastic polymers or polymers of acrylic and methacrylic acid, esters of these acids or acrylonitrile. Acrylic acid acrylonitrile and their derivatives are described in Vol 1 of Encycl, pp A96-R A97. Methacrylic acid is a-methylacrylic acid,... 

Vinyl-type addition polymerization. Many olefins and diolefins polymerize under the influence of heat and light or in the presence of catalysts, such as free radicals, carbomum ions or carbamons. Free radicals are particularly efficient in starting polymerization of such important monomers as styrene, vinylchloride, vinylacetate, methylacrylate or acrylonitrile. The first step of this process—the so-called initiation step—consists in the thermal or photochemical dissociation of the catalyst, and results in the formation of two free radicals-. 

Michael addition. Ostaszynski and Wielgat 58] used potassium (luoride as j talysi for the Michael addition of nitromethane to a double bond. (Alkali lorides were originally suggested by Yasuda ct al. [59] as catalysts foi the chael addition reactions.) The work of addition of nitroalkanes was continued J]- Various acceptors, for example, methylacrylate and acrylonitrile, were fd. Among nitroalkanes gem-dinitroalkancs were applied as donors. Nitro-ICS readily formed double salts with KHFj, RbHFj and CsHFj. The yield Ihe adducts of such salts with compounds containing a double bond varied reen 60 and 90%, viz. (5) ... 

The first generation of tubular implants for PN repair were made of silicone rubber, which showed some success [68, 69, 72, 145]. Another non-degradable material is poly(acrylonitrile-co-methylacrylate) (PAN-MA). Recently, a peripheral nerve... 

Since the Arimoto/Haven report of vinylferrocene polymerization was not detailed, this monomer was made and both its homopolymerization and its copolymerization were studied with a variety of organic comonomers such as styrene, methylacrylate, maleic anhydride, acrylonitrile, methyl methacrylate, N-vinylpyrolidone, vinyl acetate, and so on.31-38 The polymers were as well characterized as possible, and copolymer compositions were obtained versus feed mole ratios. 

---