Acrylic polymer content, effect

Unlike most crystalline polymers, PVDF exhibits thermodynamic compatibiUty with other polymers (133). Blends of PVDF and poly(methyl methacrylate) (PMMA) are compatible over a wide range of blend composition (134,135). SoHd-state nmr studies showed that isotactic PMMA is more miscible with PVDF than atactic and syndiotactic PMMA (136). MiscibiUty of PVDF and poly(alkyl acrylates) depends on a specific interaction between PVDF and oxygen within the acrylate and the effect of this interaction is diminished as the hydrocarbon content of the ester is increased (137). Strong dipolar interactions are important to achieve miscibility with poly(vinyhdene fluoride) (138). PVDF blends are the object of many papers and patents specific blends of PVDF and acryflc copolymers have seen large commercial use. 

In Fig. 1 the hopper flow time of the various mortars is shown. It can clearly be seen that the addition of the polymer dispersions has no significant effect on the hopper flow time. After adding the styrene-acrylate, the hopper flow time of the reference mortar composition decreased slightly from 42.8s to 36.4s/40.0s without segregation of the mortar. Furthermore, the addition of styrene-butadiene has led to a decrease in the hopper flow time, which can be attributed to the improvement of workability after the addition of the polymer dispersion. However, the two polymer types showed different tendencies in the hopper flow time. With styrene-butadiene, the hopper flow time decreases with higher polymer content, whereas the hopper flow time increases with a higher content of styrene-acrylate. 

So-called core-shell impact modifiers have a less damaging effect on the modulus and HDT. They are made by emulsion graft polymerisation, and consist of two parts. As their name implies, one part is an outer shell of a hard acrylic polymer-like PMMA, in direct contact with the polymer that needs toughening the two must be compatible. (In the case of SAN copolymers, the compatibility depends on the polarity, and hence on the nitrogen content of the copolymer.)... 

Another effect of silicate nanoparticles is to reduce the gloss of UV-cured acrylic polymers, even at a relatively low filler load, as shown in Fig. 7.13. An organoclay content of 1 wt.% proved already sufficient to cut by half the gloss of... 

PCA 16 is available as Beldene 161/164 (50/35% w/w solids), Acumer 4161 (50%), and Polysperse (50%). These are low-phosphorus content materials that have found application in boiler FW formulations because of excellent sludge conditioning and particulate dispersion properties. The number 16 represents a 16 1 w/w ratio of acrylic acid and sodium hypophosphite, giving PCA 16 a MW range of 3,300 to 3,900. PCA 16 is particularly effective for the control of calcium carbonate and sulfate deposition. It is usually incorporated with other polymers in formulations and is approved for use under U.S. CFR 21, 173.310. 

Hydrolysis of amide groups to carboxylate is a major cause of instability in acrylamide-based polymers, especially at alkaline pH and high temperatures. The performance of oil-recovery polymers may be adversely affected by excessive hydrolysis, which can promote precipitation from sea water solution. This work has studied the effects of the sodium salts of acrylic acid and AMPS, 2-acrylamido-2-methylpropanesulfonic acid, as comonomers, on the rate of hydrolysis of polyacrylamides in alkaline solution at high temperatures. Copolymers were prepared containing from 0-53 mole % of the anionic comonomers, and hydrolyzed in aqueous solution at pH 8.5 at 90°C, 108°C and 120°C. The extent of hydrolysis was measured by a conductometric method, analyzing for the total carboxylate content. 

In order to achieve the above objectives, three vinyl acrylic latexes of varying butyl acrylate content have been prepared and cleaned1 for use in the study. Several anionic and nonionic surfactants commonly usod in emulsion polymerization have been used to investigate the effects of surfactant structure and polymer composition on the solubilization process. Polarity of latex surface estimated from contact angle measurements have been used to study the effect of polymer polarity on surfactant adsorption. 

As reported by Diehl et al. [58], interpolymers are also compatible with a broader range of polymers, including styrene block copolymers [59], poly(vinyl chloride) (PVC)-based polymers [60], poly(phenylene ethers) [61] and olefinic polymers such as ethylene-acrylic acid copolymer, ethylene-vinyl acetate copolymer and chlorinated polyethylene. Owing to their unique molecular structure, specific ESI have been demonstrated as effective blend compatibilizers for polystyrene-polyethylene blends [62,63]. The development of the miscibility/ compatibility behavior of ESI-ESI blends differing in styrene content will be highlighted below. 

As reported in Table 15, the kinetic data clearly indicate that the photoinitiation activity of poly(BMOA-co-MtA) is not substantially affected by the content of BMOA co-units along the polymer chain and is of the same order of magnitude as that found for the model compound BMOAc. The absence of a polymer effect in the above photoinitiators has been interpreted [84] in terms of a photodegradation mechanism of the macromolecules involving the ftee radical species anchored to the main chain, even in the presence of acrylic monomers, analogous to what is reported in Scheme 18. Moreover, the induction period of the HDDA/BA photoinduced polymerization increases, on decreasing the content of... 

---