Acetic acid dioxide removal

Equal weights of distilled p-phenetidine and glacial acetic acid are heated under a reflux with the addition of a little fused sodium acetate until no free base remains (diazotise and test with alkaline j8-naphthol). The excess acetic acid is removed by distillation in vacuo, and the residue dissolved in boiling water to which animal charcoal is added, and after cooling and filtering, phenacetin separates out. It is filtered, washed, and recrystallised from water or 60% alcohol, a little sulphur dioxide solution being added to prevent oxidation. 

Place 125 ml. of glacial acetic acid, 7 -5 g. of purifled red phosphorus (Section II,50,d) and 2 5 g. of iodine in a 500 ml, round-bottomed flask fitted with a reflux condenser. Allow the mixture to stand for 15-20 minutes with occasional shaking until aU the iodine has reacted, then add 2 5 ml. of water and 50 g, of benzilic acid (Section IV,127). Boil the mixture under reflux for 3 hours, and filter the hot mixture at the pump through a sintered glass funnel to remove the excess of red phosphorus. Pour the hot filtrate into a cold, weU-stirred solution of 12 g. of sodium bisulphite in 500 ml, of water the latter should be acid to litmus, pro duced, if necessary, by passing sulphur dioxide through the solution. This procedure removes the excess of iodine and precipitates the diphenyl-acetic acid as a fine white or pale yellow powder. Filter the solid with suction and dry in the air upon filter paper. The yield is 45 g., m.p. 

To illustrate the specific operations involved, the scheme below shows the first steps and the final detachment reaction of a peptide synthesis starting from the carboxyl terminal. N-Boc-glycine is attached to chloromethylated styrene-divinylbenzene copolymer resin. This polymer swells in organic solvents but is completely insoluble. ) Treatment with HCl in acetic acid removes the fert-butoxycarbonyl (Boc) group as isobutene and carbon dioxide. The resulting amine hydrochloride is neutralized with triethylamine in DMF. 

Sodium acetate reacts with carbon dioxide in aqueous solution to produce acetic anhydride and sodium bicarbonate (49). Under suitable conditions, the sodium bicarbonate precipitates and can be removed by centrifugal separation. Presumably, the cold water solution can be extracted with an organic solvent, eg, chloroform or ethyl acetate, to furnish acetic anhydride. The half-life of aqueous acetic anhydride at 19°C is said to be no more than 1 h (2) and some other data suggests a 6 min half-life at 20°C (50). The free energy of acetic anhydride hydrolysis is given as —65.7 kJ/mol (—15.7 kcal/mol) (51) in water. In wet chloroform, an extractant for anhydride, the free energy of hydrolysis is strangely much lower, —50.0 kJ/mol (—12.0 kcal/mol) (51). Half-life of anhydride in moist chloroform maybe as much as 120 min. Ethyl acetate, chloroform, isooctane, and / -octane may have promise for extraction of acetic anhydride. Benzene extracts acetic anhydride from acetic acid—water solutions (52). 

Carbonate is measured by evolution of carbon dioxide on treating the sample with sulfuric acid. The gas train should iaclude a silver acetate absorber to remove hydrogen sulfide, a magnesium perchlorate drying unit, and a CO2-absorption bulb. Sulfide is determined by distilling hydrogen sulfide from an acidified slurry of the sample iato an ammoniacal cadmium chloride solution, and titrating the precipitated cadmium sulfide iodimetrically. 

A solution of 11.2 g of potassium permanganate in 100 ml of warm water was added drop-wise to a well stirred solution of 10 g of 2-(4-chlorophenyl)-3-methyl-4-metathiazanone in 50 ml of glacial acetic acid. The temperature was kept below 30°C with external cooling. An aqueous sodium bisulfite solution was then added to remove the manganese dioxide. The thick whitish oil which separated was taken up in chloroform and the extract was washed with water. Removal of the chloroform by distillation in vacuo yielded an oily residue which solidified. The solid was recrystallized from isopropyl alcohol to give 5 g of the product, 2-(4-chlorophenyl)-3-methyl-4-metathiazanone-1,1-dioxide, MP 116.2° to 118.6°C (corr.). 

Ethyl 2-(D-amiino-tetrahydroxybutyl)-5-methyl-4-furoate (5.5 g.) is mixed with 80 ml. of dry benzene and 20 ml. of glacial acetic acid, and cooled in ice plus water. While stirring and cooling, 182 g. of lead tetraacetate (purity, 99.7%)62 is added during about sixty minutes stirring is continued until all the oxidant has been consumed. The lead dioxide is then removed by filtration, and the benzene solution is extracted twice with water.58 The benzene layer is dried with calcium chloride and the solvent is evaporated under diminished pressure, giving an oily residue which rapidly crystallizes in colorless plates yield, 3.6 g. (quantitative). The product is purified by recrystallization from dilute acetic acid or by steam distillation m.p., 57°. 

After treatment of XXXVI with aqueous barium hydroxide, the liquor contained formic, methoxyacetic, and ethoxyacetic acids, methoxyacetone, and ethoxyacetone, produced by the two modes of cleavage XXXVIa and XXXVIb. Formic acid was converted with red mercuric oxide to carbon dioxide this was recovered as barium carbonate, the radioactivity of which was a measure of the C14 incorporated into Cl of kojic acid in the biosynthetic process. The alkoxyacetones were removed from the liquor by steam distillation, and converted to iodoform and a mixture of methoxy- and ethoxy-acetic acids. The iodoform was recovered by filtration its radioactivity indicated the proportion of C14 incorporated into C4. The alkoxy-... 

Chemical/Physical. Ozonolysis of acetic acid in distilled water at 25 °C yielded glyoxylic acid which oxidized readily to oxalic acid before undergoing additional oxidation producing carbon dioxide. Ozonolysis accompanied by UV irradiation enhanced the removal of acetic acid (Kuo et al, 1977). 

To the crude diethyl o-nitrobenzoylmalonate is added a solution of 60 ml. of glacial acetic acid, 7.6 ml. of concentrated sulfuric acid, and 40 ml. of water, and the mixture is heated under reflux for 4 hours (Note 4) or until no more carbon dioxide is evolved. The reaction mixture is chilled in an ice bath, made alkaline with 20% sodium hydroxide solution, and extracted with several portions of ether. The combined ethereal extracts are washed with water and dried with anhydrous sodium sulfate followed by Drierite, and the solvent is removed by distillation. On fractional distillation of the residue, 27.0-27.4 g. (82-83%) of light-yellow o-nitroacetophenone boiling at 158-159°/16 mm. is obtained n 1.548, wg 1.551, df 1.236) (Note 5). 

The isomerization of allyl ethers to 1-propenyl ethers, which is usually performed with potassium tert-butoxide in dimethyl sulfoxide, can also be carried out under milder conditions using tris(triphen-ylphosphine)rhodium chloride,208 and by an ene reaction with diethyl azodicarboxylate,209,210 which affords a vinyl ether adduct. Removal of an O-allyl group may be achieved by oxidation with selenium dioxide in acetic acid,211 and by treatment with N-bromosuccinimide, followed by an aqueous base.201,212... 

The current method (3, 4, 6, 22) involves steam distillation to separate the volatile (primarily acetic) acids from the non-volatile (fixed) acids. Special equipment has been devised for this separation (6). Sulfurous and sorbic acid content can be corrected, or the sulfurous acid may be removed (33). Carbon dioxide must be removed so that it does not interfere with the test (6, 33). An automated procedure is also available (34) which measures the volatile acids in the distillate at 450 nm using bromophenol blue. 

---