Water as extractant

The use of modifiers occasionally improves the extraction process. Water as extractant can be modified with organic solvents such as methanol, acetone or acetonitrile in low proportions (< 5%) in order to decrease its dielectric constant — and hence its polarity — without the need for a drastic temperature increase [37]. Also, an acid or base can be used to alter the pH in those cases where it significantly influences the extraetion yield [29,46]. On the other hand, surfactants facilitate the extraction of non-polar compounds by formation of micelles [47]. Modifiers are less frequently used with extractants other than water. One example is the addition of sodium acetate to methanol to extract organotins (OTs) the additive increases the efficiency in two ways, namely (a) acetate ion by complexing OTs and (b) sodium ion through cation exchange of OTs sorbed to the clay fraction of sediments [21]. 

Bogialli S, Curini R, Di Corcia A, et al., A rapid confirmatory method for analysing tetracycline antibiotics in bovine, swine and poultry muscle tissues Matrix solid phase dispersion with heated water as extractant followed by hquid chromatography tandem mass spectrometry, J. Agric. Food Chem. 2006 54 1564-1570. 

Make a thin paste of 21 5 g. of finely-powdered o-tolidine (a commercial product) with 300 ml. of water in a 1-litre beaker, add 25 g. (21 ml.) of concentrated hydrochloric acid, and warm until dissolved. Cool the solution to 10° with ice, stir mechanically, and add a further 25 g. (21 ml.) of concentrated hydrochloric acid (1) partial separation of o tolidine dihydrochloride will occur. Add a solution of 15 g, of sodium nitrite in 30 ml. of water as rapidly as possible, but keep the temperature below 15° a slight excess of nitrous acid is not harmful in this preparation. Add the clear, orange tetrazonium solution to 175 ml. of 30 per cent, hypophosphorous acid (2), and allow the mixture to stand, loosely stoppered, at room temperature for 16-18 hours. Transfer to a separatory funnel, and remove the upper red oily layer. Extract the aqueous layer with 50 ml, of benzene. Dry the combined upper layer and benzene extract with anhydrous magnesium sulphate, and remove the benzene by distillation (compare Fig. II, 13, 4) from a Widmer or similar flask (Figs. II, 24, 3-5) heat in an oil bath to 150° to ensure the removal of the last traces of benzene. Distil the residue at ca. 3 mm. pressure and a temperature of 155°. Collect the 3 3 -dimethyldiphenyl as a pale yellow liquid at 114-115°/3 mm. raise the bath temperature to about 170° when the temperature of the thermometer in the flask commences to fall. The yield is 14 g. 

Y-Phenylbutyric acid. Prepare amalgamated zinc from 120 g. of zinc wool contained in a 1-litre rovmd-bottomed flask (Section 111,50, IS), decant the liquid as completely as possible, and add in the following order 75 ml. of water, 180 ml. of concentrated hydrochloric acid, 100 ml. of pure toluene (1) and 50 g. of p benzoylpropionic acid. Fit the flask with a reflux condenser connected to a gas absorption device (Fig. II, 8, l,c), and boil the reaction mixture vigorously for 30 hours add three or four 50 ml. portions of concentrated hydrochloric acid at approximately six hour intervals during the refluxing period in order to maintain the concentration of the acid. Allow to cool to room temperature and separate the two layers. Dilute the aqueous portion with about 200 ml. of water and extract with three 75 ml. portions of ether. Combine the toluene layer with the ether extracts, wash with water, and dry over anhydrous magnesium or calcium sulphate. Remove the solvents by distillation under diminished pressure on a water bath (compare Fig. II, 37, 1), transfer the residue to a Claisen flask, and distil imder reduced pressure (Fig. II, 19, 1). Collect the y-phenylbutyric acid at 178-181°/19 mm. this solidifies on coohng to a colourless sohd (40 g.) and melts at 47-48°. 

In summary, solvents can influence Diels-Alder reactions through a multitude of different interactions, of which the contributions to fire overall rate uniquely depend on the particular solvent-diene-dienophile combination. Scientists usually feel uncomfortable about such a situation and try to extract generalities. When limited to the most extensively studied type A Diels-Alder reactions this approach seems feasible. These Diels-Alder reactions are dominated by hydrogen bonding interactions in combination with solvophobic interactions. This observation predicts a very special role of water as a solvent for type A Diels-Alder reactions, which is described in Section 1.4. 

Now the chemist need only extract the MDA oil from the water with some DCM. Yes, this time the MDA will go into the DCM. The chemist merely pours about 400mLs of DCM into the container and stirs it really well for a few minutes while she watches TV. As much of the water as possible is poured off or separated... 

By far the best method I have tried to produce benzodioxole in terms of yields and simplicity. In comparison to other processes, this is in fact quite fun and I ll explain It in a fashion that can be followed by a complete novice, like I was when I started a while ago. What we do is react and reflux the ingredients first, then use a simple distillation procedure to extract the product with water as an azeotrope. Once extracted we wash until the product is clear, and then separate. From start to finish it will take about six hours. 

It requires a certain flexibility of mind to accept the proposal of using the same THF as extraction solvent in some cases. Ue discovered this possibility, when we tried to remove this solvent from carboxylic acids in a water-pump, vacuum it appeared difficult to remove the last traces of this solvent, even when heating at 70-80°C in a vacuum of 10-15 mmHg was applied. It seemed that there is some weak complexation. This led us to the idea of using THF for the extraction of carboxylic acids from the aqueous phase (after saturation with... 

To absolution of 1.00 mol of ethyl lithium in 800-900 ml of diethyl ether (see Chapter II, Exp. 1) was added, with cooling between -20 and -10°C, 0.50 nol of dry propargyl alcohol, dissolved in 100 ml of diethyl ether. Subsequently 1.1 mol of trimethylchlorosilane was introduced over a period of 25 min with cooling between -15 and +5°C. After stirring for an additional 2 h at about 30°C the suspension was poured into a solution of 30 g of acetic acid in 150 ml of water. After stirring for 1 h at room temperature the layers were separated and the aqueous layer v/as extracted four times with diethyl ether. The combined ethereal solutions were washed with sodium hydrogen carbonate solution in order to neutralize acetic acid, and were then dried over magnesium sulfate. The diethyl ether was removed by evaporation in a water-pump vacuum and the residue distilled... 

Historically, soda ash was produced by extracting the ashes of certain plants, such as Spanish barilla, and evaporating the resultant Hquor. The first large scale, commercial synthetic plant employed the LeBlanc (Nicolas LeBlanc (1742—1806)) process (5). In this process, salt (NaCl) reacts with sulfuric acid to produce sodium sulfate and hydrochloric acid. The sodium sulfate is then roasted with limestone and coal and the resulting sodium carbonate—calcium sulfide mixture (black ash) is leached with water to extract the sodium carbonate. The LeBlanc process was last used in 1916—1917 it was expensive and caused significant pollution. 

A pilot plant ia India has been estabUshed to extract fiber, pulp, and juice from the leaves of sisal plants. The fiber is sold direcdy or used to manufacture rope, the cmshed pulp is used ia paper processiag, and the juice is an excellent source of hecogenin. During a three- to five-day fermentation of the juice, partial enzymatic hydrolysis causes hecogenin to precipitate as the hemisaponin ia the form of a fine sludge. This sediment is hydrolyzed with aqueous hydrochloric acid, neutralized, and filtered. This filter cake is washed with water and extracted with alcohol. The yield of hecogenin varies between 0.05 and 0.1% by the weight of the leaf (126). 

---