Water, acid motion

Allyl Bromide. Introduce into a 1-litre three-necked flask 250 g. (169 ml.) of 48 per cent, hydrobromic acid and then 75 g. (40-5 ml.) of concentrated sulphuric acid in portions, with shaking Anally add 58 g. (68 ml.) of pure allyl alcohol (Section 111,140). Fit the flask with a separatory funnel, a mechanical stirrer and an efficient condenser (preferably of the double surface type) set for downward distillation connect the flask to the condenser by a wide (6-8 mm.) bent tube. Place 75 g. (40 5 ml.) of concentrated sulphuric acid in the separatory funnel, set the stirrer in motion, and allow the acid to flow slowly into the warm solution. The allyl bromide will distil over (< 30 minutes). Wash the distillate with 5 per cent, sodium carbonate solution, followed by water, dry over anhydrous calcium chloride, and distil from a Claisen flask with a fractionating side arm or through a short column. The yield of allyl bromide, b.p. 69-72°, is 112 g. There is a small high-boiling fraction containing propylene dibromide. 

C. Fumaric acid from furfural. Place in a 1-litre three-necked flask, fitted with a reflux condenser, a mechanical stirrer and a thermometer, 112 5 g. of sodium chlorate, 250 ml. of water and 0 -5 g. of vanadium pentoxide catalyst (1), Set the stirrer in motion, heat the flask on an asbestos-centred wire gauze to 70-75°, and add 4 ml. of 50 g. (43 ml.) of technical furfural. As soon as the vigorous reaction commences (2) bvi not before, add the remainder of the furfural through a dropping funnel, inserted into the top of the condenser by means of a grooved cork, at such a rate that the vigorous reaction is maintained (25-30 minutes). Then heat the reaction mixture at 70-75° for 5-6 hours (3) and allow to stand overnight at the laboratory temperature. Filter the crystalline fumaric acid with suction, and wash it with a little cold water (4). Recrystallise the crude fumaric acid from about 300 ml. of iif-hydrochloric acid, and dry the crystals (26 g.) at 100°. The m.p. in a sealed capillary tube is 282-284°. A further recrystaUisation raises the m.p. to 286-287°. 

For the HCI salt Do exactly as above except use 6N Hydrochloric Acid. 6N HCI may be produced by diluting 60.4mL of "Muriatic Acid" to lOOmL with distilled water. Evaporate the bubbler solution to dryness then add 15ml of water, lOmL 10% NaOH soln. and heat gently to a boil with constant motion until dense white fumes appear. This will remove the Ammonium Chloride. Remove from heat while stirring as it cools down. Pulverize the dry residue, then reflux with absolute Ethanol for several minutes. Filter the refluxed soln. on a heated Buchner or Hirsch funnel, then distill the alcohol off the filtrate until crystals just begin to form. Allow the soln. to cool naturally to room temperature, then cool further in an ice bath. Filter the solution on a chilled Buchner funnel with suction. The yield of Meth iamine Hydrochloride should be around 55% of the theoretical. 

Prepare 250 mL of 0.02 M potassium dichromate solution and an equal volume of ca 0.1 M ammonium iron(II) sulphate solution the latter must contain sufficient dilute sulphuric acid to produce a clear solution, and the exact weight of ammonium iron(II) sulphate employed should be noted. Place 25 mL of the ammonium iron(II) sulphate solution in the beaker, add 25 mL of ca 2.5M sulphuric acid and 50 mL of water. Charge the burette with the 0.02 M potassium dichromate solution, and add a capillary extension tube. Use a bright platinum electrode as indicator electrode and an S.C.E. reference electrode. Set the stirrer in motion. Proceed with the titration as directed in Experiment 1. After each addition of the dichromate solution measure the e.m.f. of the cell. Determine the end point (1) from the potential-volume curve and (2) by the derivative method. Calculate the molarity of the ammonium iron(II) sulphate solution, and compare this with the value calculated from the actual weight of solid employed in preparing the solution. 

---