Tungsten detection

Tungsten is usually identified by atomic spectroscopy. Using optical emission spectroscopy, tungsten in ores can be detected at concentrations of 0.05—0.1%, whereas x-ray spectroscopy detects 0.5—1.0%. ScheeHte in rock formations can be identified by its luminescence under ultraviolet excitation. In a wet-chemical identification method, the ore is fired with sodium carbonate and then treated with hydrochloric acid addition of 2inc, aluminum, or tin produces a beautiful blue color if tungsten is present. 

In the continuous wave (CW) experimental setup a sample is constantly illuminated by a probe beam and the steady state change in the transmission is detected (see Fig. 7-1). An argon ion laser has been used to generate the pump beam and the probe beam was from an incandescent lamp (tungsten or others), producing a broad spectrum (0.5 to 5 pm) [6]. Both pump and probe beams are directed onto the sample film and the transmitted probe light is collected, filtered through a monochromator, and detected by a photodetector. Both the pump and the probe... 

D. gigas formate dehydrogenase seems to be quite different in terms of subunit composition. It does not contain a y subunit and no heme c was detected (225). Also, two MGD were identified, but surprisingly, the enzyme contains tungsten instead of molybdenum. Mossbauer and EPR studies confirmed the presence of two [4Fe-4S] + + clusters with similar properties to the ones found in D. desulfuricans FDH (247). 

HREELS experiments [66] were performed in a UHV chamber. The chamber was pre-evacuated by polyphenylether-oil diffusion pump the base pressure reached 2 x 10 Torr. The HREELS spectrometer consisted of a double-pass electrostatic cylindrical-deflector-type monochromator and the same type of analyzer. The energy resolution of the spectrometer is 4-6 meV (32-48 cm ). A sample was transferred from the ICP growth chamber to the HREELS chamber in the atmosphere. It was clipped by a small tantalum plate, which was suspended by tantalum wires. The sample was radia-tively heated in vacuum by a tungsten filament placed at the rear. The sample temperature was measured by an infrared (A = 2.0 yum) optical pyrometer. All HREELS measurements were taken at room temperature. The electron incident and detection angles were each 72° to the surface normal. The primary electron energy was 15 eV. 

Fig. 1. Schematic diagram of the multimass ion imaging detection system. (1) Pulsed nozzle (2) skimmers (3) molecular beam (4) photolysis laser beam (5) VUV laser beam, which is perpendicular to the plane of this figure (6) ion extraction plate floated on V0 with pulsed voltage variable from 3000 to 4600 V (7) ion extraction plate with voltage Va (8) outer concentric cylindrical electrode (9) inner concentric cylindrical electrode (10) simulation ion trajectory of m/e = 16 (11) simulation ion trajectory of rri/e = 14 (12) simulation ion trajectory of m/e = 12 (13) 30 (im diameter tungsten wire (14) 8 x 10cm metal mesh with voltage V0] (15) sstack multichannel plates and phosphor screen. In the two-dimensional detector, the V-axis is the mass axis, and V-axis (perpendicular to the plane of this figure) is the velocity axis (16) CCD camera.

Complex 7-AI2O3/PTA/ (/< ./< )-(Mc-DuPHOS)Rh(COD) 1 (1) was prepared and tested in the hydrogenation of the prochiral substrate methyl-2-acetamidoacrylate (MAA). After full conversion, the products were separated from the catalyst and analyzed for Rh and W content and product selectivity. The catalyst was re-used three times. Analytical results show no rhodium leaching is observed. Complex 1 maintains its activity and selectivity in each successive run. The first three runs show tungsten (W) leaching but after that no more W is detectable. The leached W comes from the excess of PTA on alumina. The selectivity of both tethered and non-tethered forms gave the product in 94% ee. 

---