Toluene esterification

Acrylic acid, p-toluenesulphuric acid (PTS) as a catalyst, and hydroqui-none (HQ) as a polymerisation inhibitor were added to solutions of the OH-terminated oligomers in toluene. Esterification proceeded by removing the formed water. The excess acrylic acid, PTS, and HQ were neutralised by NaOH solutions and then desalted. The reaction mixture was extracted by toluene, and toluene was evaporated under vacuum to obtain a pale-yellowish viscous liquid (Fig. 12.4). 

The distillate contains alcohol, toluene and water, and may be dried with anhydrous potassium carbonate and used again for esterification after the addition of the necessary quantity of alcohol alternatively, the toluene may be recovered by washing with water, drying with anhydrous calcium chloride or anhydrous magnesium sulphate, and distiUing. 

Chlorendic Acid. Chlorendic acid [115-28-6] and its anhydride [115-27-5] are widely used flame retardants. Chlorendic acid is synthesized by a Diels-Alder reaction of maleic anhydride and hexachlorocyclopentadiene (see CyclopentadlENE and dicyclopentadiente) in toluene followed by hydrolysis of the anhydride using aqueous base (60). The anhydride can be isolated directly from the reaction mixture or can be prepared in a very pure form by dehydration of the acid. The principal use of chlorendic anhydride and chlorendic acid has been in the manufacture of unsaturated polyester resins. Because the esterification rate of chlorendic anhydride is similar to that of phthalic anhydride, it can be used in place of phthalic anhydride in commercial polyester... 

In typical processes, the gaseous effluent from the second-stage oxidation is cooled and fed to an absorber to isolate the MAA as a 20—40% aqueous solution. The MAA may then be concentrated by extraction into a suitable organic solvent such as butyl acetate, toluene, or dibutyl ketone. Azeotropic dehydration and solvent recovery, followed by fractional distillation, is used to obtain the pure product. Water, solvent, and low boiling by-products are removed in a first-stage column. The column bottoms are then fed to a second column where MAA is taken overhead. Esterification to MMA or other esters is readily achieved using acid catalysis. 

The toluenesulfonic acid prepared as an iatermediate ia the preparation ofpara-cmso also has a modest use as a catalyst for various esterifications and condensations. Sodium salts of the toluenesulfonic acids are also used ia surfactant formulations. Annual use of toluene for sulfonation is ca 100,000-150,000 t (30-45 x 10 gal). 

Esters of low volatility are accesible via several types of esterification. In the case of esters of butyl and amyl alcohols, water is removed as a binary azeotropic mixture with the alcohol. To produce esters of the lower alcohols (methyl, ethyl, propyl), it may be necessary to add a hydrocarbon such as benzene or toluene to increase the amount of distilled water. With high boiling alcohols, ie, benzyl, furfuryl, and P-phenylethyl, an accessory azeotroping Hquid is useful to eliminate the water by distillation. 

Reactive compatibilization of engineering thermoplastic PET with PP through functionalization has been reported by Xanthos et al. [57]. Acrylic acid modified PP was used for compatibilization. Additives such as magnesium acetate and p-toluene sulfonic acid were evaluated as the catalyst for the potential interchange or esterification reaction that could occur in the melt. The blend characterization through scanning electron microscopy, IR spectroscopy, differential scanning calorimetry, and... 

Determination of carboxy groups. Esterification or polyesterification kinetics is usually followed by this titration which is both easy and accurate. Each sample is dissolved in a solvent or a mixture of solvents (CHCI3, QH /EtOH or MeOH, toluene/EtOH or MeOH...) and then titrated with alcoholic KOH. The end point is determined either with an indicator (in most cases phenolphthalein) or with a pH-meter. An accuracy of about 0.1-1% can generally be achieved. 

In the case of simple amino acids and dipeptides, esterification of the carboxyl groups occurs on heating in toluene with the appropriate bis(triorganotin) oxide or triorganotin hydroxide 481, 482), the water being removed azeotropically. 

Aqueous solutions are not suitable solvents for esterifications and transesterifications, and these reactions are carried out in organic solvents of low polarity [9-12]. However, enzymes are surrounded by a hydration shell or bound water that is required for the retention of structure and catalytic activity [13]. Polar hydrophilic solvents such as DMF, DMSO, acetone, and alcohols (log P<0, where P is the partition coefficient between octanol and water) are incompatible and lead to rapid denaturation. Common solvents for esterifications and transesterifications include alkanes (hexane/log P=3.5), aromatics (toluene/2.5, benzene/2), haloalkanes (CHCI3/2, CH2CI2/I.4), and ethers (diisopropyl ether/1.9, terf-butylmethyl ether/ 0.94, diethyl ether/0.85). Exceptionally stable enzymes such as Candida antarctica lipase B (CAL-B) have been used in more polar solvents (tetrahydrofuran/0.49, acetonitrile/—0.33). Room-temperature ionic liquids [14—17] and supercritical fluids [18] are also good media for a wide range of biotransformations. 

The acid in this step clearly functions as a catalyst (acids are known to catalyze the esterification of silanols) (21). The toluene, when employed, serves to drive the esterification to completion by forming a water-toluene-ethanol azeotrope (12% water) (22). It also renders the reaction solution a poor solvent for the byproduct salts and thus facilitates the separation of these salts (the pentane, when used, serves this same function). 

Enanthaldehyde, -METHYL-/3-OXO-, DIMETHYL ACETAL, 32, 79 Enanthic acid, e-oxo, 31, 3 Epichlorohydrin, 31, 1 Esterification, by azeotropic distillation with toluene, 30, 30, 31 of ethanol with phosphorus trichloride, 31, 111... 

The desired polymer-bound tryptophan was rapidly generated under microwave irradiation, employing a classical esterification protocol using N,N -dicydohexylcar-bodiimide (DCC) and a catalytic amount of N,N-dimethylaminopyridine (DMAP), followed by subsequent Fmoc deprotection (Scheme 7.68). Cyclocondensations with various carbonyl compounds were performed with catalytic amounts of p-toluene-... 

The reagent is prepared1 by reaction of phosgene with 3,5-dioxo-4-methyl-l,2,4-oxadiazolidine in refluxing toluene (82% yield). It serves as a coupling reagent for esterification and preparation of amides and carbamates. 

---