Thermal analysis difference

The thermal conductivity of gas-phase deuterium is about 0.73 times that of gas-phase hydrogen. This thermal conductivity difference offers a convenient method for analysis of H2—D2 mixtures. Other physical properties of D2, T2, HD, DT, and HT are Hsted in the Hterature (60). 

The hydrated alumina minerals usually occur in ooUtic stmctures (small spherical to eUipsoidal bodies the size of BB shot, about 2 mm in diameter) and also in larger and smaller stmctures. They impart harshness and resist fusion or fuse with difficulty in sodium carbonate, and may be suspected if the raw clay analyzes at more than 40% AI2O2. Optical properties are radically different from those of common clay minerals, and x-ray diffraction patterns and differential thermal analysis curves are distinctive. 

Order of thermal stabiUty as determined by differential thermal analysis is sebacic (330°C) > a2elaic = pimelic (320°C) > suberic = adipic = glutaric (290°C) > succinic (255°C) > oxahc (200°C) > malonic (185°C) (19). This order is somewhat different than that in Table 2, and is the result of differences in test conditions. The energy of activation for decarboxylation has been estimated to be 251 kj/mol (60 kcal/mol) for higher members of the series and 126 kJ/mol (30 kcal/mol) for malonic acid (1). 

The techniques referred to above (Sects. 1—3) may be operated for a sample heated in a constant temperature environment or under conditions of programmed temperature change. Very similar equipment can often be used differences normally reside in the temperature control of the reactant cell. Non-isothermal measurements of mass loss are termed thermogravimetry (TG), absorption or evolution of heat is differential scanning calorimetry (DSC), and measurement of the temperature difference between the sample and an inert reference substance is termed differential thermal analysis (DTA). These techniques can be used singly [33,76,174] or in combination and may include provision for EGA. Applications of non-isothermal measurements have ranged from the rapid qualitative estimation of reaction temperature to the quantitative determination of kinetic parameters [175—177]. The evaluation of kinetic parameters from non-isothermal data is dealt with in detail in Chap. 3.6. 

Thermal analysis has been widely and usefully applied in the solution of technical problems concerned with the commercial exploitation of natural dolomite including, for example, the composition of material in different deposits, the influence of impurities on calcination temperatures, etc. This approach is not, however, suitable for the reliable determination of kinetic parameters for a reversible reaction (Chap. 3, Sect. 6). 

The Ca-Cu system has been reexamined using thermal analysis and x-ray diffraction methods an independent study of the CaCuj-Cu section has also been completed. The resultant phase diagram, although similar to that in ref. 3 at the Cu-rich end, differs markedly for Ca-rich alloys. Supporting evidence for the modifications has been obtained from the Ca-Mg-Cu ternaiy system. Three intermediate compounds are formed in the system CaCuj (950 C) melts congruently, whereas CajCu (488 C) and CaCu (567°C) are formed in peritectic reactions. Single-crystal x-ray diffraction studies verify the stoichiometry of CajCu and examine the polymorphism of CaCu. ... 

When solids react, we would like to know at what temperature the solid state reaction takes place. If the solid decomposes to a different composition, or phase, we would like to have this knowledge so that we can predict and use that knowledge In preparation of desired materials. Sometimes, intermediate compounds form before the final phase. In this chapter, we will detail some of the measurements used to characterize the solid state and methods used to foUow solid state reactions. This will consist of various types of thermal analysis (TA), including differentlEd thermal analysis (DTA), thermogravimetric analysis (TGA) and measurements of optical properties. 

Another reported study involved the preparation of four niclosamide solvates and the determination of the stability of the crystal forms in different suspension vehicles by DSC and TG analysis. Thermal analysis showed that the niclosamide solvates were extremely unstable in a PVP-vehicle and rapidly changed to monohydrated crystals. A suspension in propylene glycol was more stable and TG analysis showed that crystal transformation was less rapid [18]. 

Differential thermal analysis (DTA) is the monitoring of the difference in temperature between a sample and a reference as a function of temperature [42], Differences in temperature between the sample and reference are observed when changes occur that require a finite heat of reaction. If AH is positive (endothermic reaction), the temperature of the sample will lag behind that of the reference. If the AH is negative (exothermic reaction), the temperature of the sample will exceed that of the reference. Differential thermal analysis is not normally used for quantitative work instead it is used to deduce temperatures associated with thermal events. 

Analogous to the DuP 747 study, complete crystallographic information was not possible on the fosinopril sodium polymorphic system [25], Two known polymorphs (A and B) were studied via a multidisciplinary approach (XRD, IR, NMR, and thermal analysis). Complementary spectral data from IR and solid state 13C NMR revealed that the environment of the acetal sidechain of fosinopril sodium differed in the two forms. In addition, possible cis-trans isomerization about the CgN peptide bond may exist. These conformational differences are postulated as the origin of the observed polymorphism in fosinopril sodium in the absence of the crystallographic data for form B (single crystals not available). 

The use of solid state NMR for the investigation of polymorphism is easily understood based on the following model. If a compound exists in two, true polymorphic forms, labeled as A and B, each crystalline form is conformationally different. This means for instance, that a carbon nucleus in form A may be situated in a slightly different molecular geometry compared with the same carbon nucleus in form B. Although the connectivity of the carbon nucleus is the same in each form, the local environment may be different. Since the local environment may be different, this leads to a different chemical shift interaction for each carbon, and ultimately, a different isotropic chemical shift for the same carbon atom in the two different polymorphic forms. If one is able to obtain pure material for the two forms, analysis and spectral assignment of the solid state NMR spectra of the two forms can lead to the origin of the conformational differences in the two polymorphs. Solid state NMR is thus an important tool in conjunction with thermal analysis, optical microscopy, infrared (IR) spectroscopy, and powder... 

It is important to ascertain whether the solid phase of the solute changes during equilibration to produce a different polymorph or solvate, by analyzing the solid phase (using either chemical or thermal analysis, or x-ray diffraction). If a solid-solid phase transition occurs during equilibration, the measured equilibrium solubility will be that of the new solid phase of the solute. Methods of circumventing this problem have been proposed and evaluated [26]. 

---