Tension measurements

The film pressure is defined as the difference between the surface tension of the pure fluid and that of the film-covered surface. While any method of surface tension measurement can be used, most of the methods of capillarity are, for one reason or another, ill-suited for work with film-covered surfaces with the principal exceptions of the Wilhelmy slide method (Section II-6) and the pendant drop experiment (Section II-7). Both approaches work very well with fluid films and are capable of measuring low values of pressure with similar precision of 0.01 dyn/cm. In addition, the film balance, considerably updated since Langmuir s design (see Section III-7) is a popular approach to measurement of V. 

Usually one varies the head of mercury or applied gas pressure so as to bring the meniscus to a fixed reference point [118], Grahame and co-workers [119], Hansen and co-workers [120] (see also Ref. 121), and Hills and Payne [122] have given more or less elaborate descriptions of the capillary electrometer apparatus. Nowadays, the capillary electrometer is customarily used in conjunction with capacitance measurements (see below). Vos and Vos [111] describe the use of sessile drop profiles (Section II-7B) for interfacial tension measurements, thus avoiding an assumption as to the solution-Hg-glass contact angle. 

Furthermore, in a series of polyoxyethylene nonylphenol nonionic surfactants, the value of varied linearly with the HLB number of the surfactant. The value of K2 varied linearly with the log of the interfacial tension measured at the surfactant concentration that gives 90% soil removal. Carrying the correlations still further, it was found that from the detergency equation of a single surfactant with three different polar sods, was a function of the sod s dipole moment and a function of the sod s surface tension (81). 

An interesting change of the UV-absorbances with electrolyte concentration was observed for A18 and T18, as shown in Fig. 5. The molar extinction coefficient of A18 decreased by about 7% at 0.09 mM, and that of T18 about 10% at 0.16 mM. These concentrations may correspond to the critical micelle concentration, since the cmc observed from the surface tension measurements were about 0.1 mM for both A18 and T18. 

Table 17 shows the CMCs of sodium alcohol propoxysulfates at 20°C determined from surface tension measurements by the maximum bubble pressure [127] and Table 18 shows the critical micelle concentrations of sodium pro-poxylated octylphenol and propoxylated nonylphenol sulfates. Surface tension... 

Studies on mechanisms are described by Balzer [192]. In the case of anionics the residual oil in the injection zone is removed via displacement into the adjacent reservoirs ether carboxylates show their good adaptation to differences in temperature and salinity. Further it was found from interfacial tension measurements, adsorption and retention studies, and flooding tests that use of surfactant blends based on ether carboxylates and alkylbenzensulfonates resulted... 

Phosphoric acid ester was used as a model for the estimation of concentration of a reagent in an adsorbed layer by optical measurements of the intensity of a beam reflecting externally from the liquid-liquid interface. The refractive index of an adsorbed layer between water and organic solution phases was measured through an external reflection method with a polarized incident laser beam to estimate the concentration of a surfactant at the interface. Variation of the interfacial concentration with the bulk concentration estimated on phosphoric acid ester in heptane and water system from the optical method agreed with the results determined from the interfacial tension measurements... 

When the CMC determination is made by surface tension measurements, the resulting curve appears without minimum as a single surfactant. It is probable that an inversion takes place through the adsorption of the LSDA onto the surface of the Ca soap micelle, so that complete precipitation does not occur [23]. Zhang and Xiao [32] are of the opinion that the dispersion comes from the union of LSDA with the free ionic soap molecules. The particles from the soap-LSDA mixture are far larger than the corresponding soap molecules in soft water and therefore result in turbidity in hard water. 

While the method based on the surface tension measurement has been established since the pioneering work of Gouy, conceptual and experimental problems arise with solid electrodes, whose surfaces cannot... 

Capacitance and interfacial tension measurements were used to study the interface between Hg and mixtures of acetone + nitromethane.330 The potential was measured against an SCEin H20 and corrected for the liquid junction potential by measuring the half-wave potential of the ferrocene-... 

Surface composition and morphology of copolymeric systems and blends are usually studied by contact angle (wettability) and surface tension measurements and more recently by x-ray photoelectron spectroscopy (XPS or ESCA). Other techniques that are also used include surface sensitive FT-IR (e.g., Attenuated Total Reflectance, ATR, and Diffuse Reflectance, DR) and EDAX. Due to the nature of each of these techniques, they provide information on varying surface thicknesses, ranging from 5 to 50 A (contact angle and ESCA) to 20,000-30,000 A (ATR-IR and EDAX). Therefore, they can be used together to complement each other in studying the depth profiles of polymer surfaces. 

Capacitance and Surface Tension Measurements of Liquid Liquid Interfaces Zdenek Samec... 

The interpretation of phenomenological electron-transfer kinetics in terms of fundamental models based on transition state theory [1,3-6,10] has been hindered by our primitive understanding of the interfacial structure and potential distribution across ITIES. The structure of ITIES was initially studied by electrochemical and thermodynamic analyses, and more recently by computer simulations and interfacial spectroscopy. Classical electrochemical analysis based on differential capacitance and surface tension measurements has been extensively discussed in the literature [11-18]. The picture that emerged from... 

Kakiuchi et al. [75] used the capacitance measurements to study the adsorption of dilauroylphosphatidylcholine at the ideally polarized water-nitrobenzene interface, as an alternative approach to the surface tension measurements for the same system [51]. In the potential range, where the aqueous phase had a negative potential with respect to the nitrobenzene phase, the interfacial capacity was found to decrease with the increasing phospholipid concentration in the organic solvent phase (Fig. 11). The saturated mono-layer in the liquid-expanded state was formed at the phospholipid concentration exceeding 20 /amol dm, with an area of 0.73 nm occupied by a single molecule. The adsorption was described by the Frumkin isotherm. 

Capacitance and surface tension measurements have provided a wealth of data about the adsorption of ions and molecules at electrified liquid-liquid interfaces. In order to reach an understanding on the molecular level, suitable microscopic models have had to be considered. Interpretation of the capacitance measurements has been often complicated by various instrumental artifacts. Nevertheless, the results of both experimental approaches represent the reference basis for the application of other techniques of surface analysis. 

Densities were measured using a Paar DMA 60 meter equipped with DMA 512 and DMA 601 HP external cells. Values in the 50-150°C range were interpolated from measured data (3-5 points) values above 150°C were extrapolated and are less accurate. Interfacial tension measurements at the minimum density difference encountered (0.05 g/cm3) could be in error by as much as 10%, which is within the repeatability of measurements with heavy crude oil samples (see below). 

Effect of NaCI Concentration. The presence of surfactant in brine can have a dramatic effect on crude oil-aqueous surfactant tensions even at elevated temperatures r5,211. Figure 5 shows that the effect of sodium chloride concentration on Athabasca bitumen-D20 interfacial tensions measured at constant surfactant... 

TABLE II. ANAEROBIC CRUDE OIL ADHESION TENSION MEASUREMENTS AND CONTACT ANGLES USING IFT = 36.4 DYNE/CM... 

Stefansson E., Peterson J.I., Wang Y.H., Intraocular oxygen tension measured with a fiber optic sensor in normal and diabetic dogs, Am. J. Phys. 1989 256 HI 127. 

Howell, E. 2001. Dynamic surface tension measurements of liquid solder using oscillating jets of elliptical cross section. Mechanical and Industrial Engineering. University of Illinois at Chicago, Chicago, IL. pp. 75. 

It is known from laboratory tests that surface tension measurement can provide reliable information regarding existing detergent concentration. Work is being carried out in various institutes on such sensors for the commercial sector. However, for use in domestic washing machines, only sensors that are extremely inexpensive, maintenance-free and durable are suitable. How much of a breakthrough can be achieved here in the future remains to be seen. 

K. Tauer, C. Dessy, S. Corkery, K.-D. Bures, On-line surface tension measurements inside stirred reactors , Colloid Polymer Sci. 1999, 277, 805-811. 

Although silicone oils by themselves or hydrophobic particles (e.g., specially treated silica) are effective antifoams, combinations of silicone oils with hydrophobic silica particles are most effective and commonly used. The mechanism of film destruction has been studied with the use of surface and interfacial tensions, measurements, contact angles, oil-spreading rates, and globule-entering characteristics for PDMS-based antifoams in a variety of surfactant solutions.490 A very recent study of the effect of surfactant composition and structure on foam-control performance has been reported.380 The science and technology of silicone antifoams have recently been reviewed.491... 

---