Temperature detachment

Isolation of Product. Remove the assembly from the hot sand bath and allow the solution to cool to room temperature. Detach the round-bottom flask, and clamp it in an ice bath for 5-10 min. Collect the light yellow crystals by vacuum filtration using a Hirsch funnel. 

Viggiano A A and Paulson J F 1983 Temperature dependence of associative detachment reactions J. Chem. Phys. 79 2241-5... 

For this purpose the thermometer has a reserve supply of mercury in the reservoir R. For working at low temperatures, more mercury is required in the bulb, and an extra supply is brought down from R for working at higher temperatures, less mercury is required in the bulb to enable readings to be made on the scale S, and therefore a suitable quantity of mercury is detached from that in the bulb and deposited in the reservoir. 

Hydrolysis of p-tolunitrile to p-toluic acid. Boil a mixture of 5 g. of p-tolunitrile, 80 ml. of 10 per cent, aqueous sodium hydroxide solution and 15 ml. of alcohol under a reflux condenser. (The alcohol is added to prevent the nitrile, which volatUises in the steam, from crystalhsing in the condenser it also increases the speed of hydrolysis. The alcohol may be omitted in the hydrolysis of nitriles which are hquid at the ordinary temperature, e.g., benzo-nitrUe.) The solution becomes clear after heating for about 1 hour, but continue the boiling for a total period of 1 - 5 hours to ensure complete hydrolysis. Detach the condenser and boil the solution for a few minutes in the open flask to remove dissolved ammonia and incidentally some of the alcohol CAUTION /). Cool, and add concentrated hydrochloric acid until precipitation of the p-toluic acid is complete. When cold, filter off the p-toluic acid with suction and wash with a little cold water. Recrystallise from a mixture of equal volumes of water and alcohol (methylated spirit) or from benzene. The yield of p-toluic acid, m.p. 178°, is 5-5 g. 

In a 500 ml. three-necked flask, equipped with a thermometer, mechanical stirrer and efficient reflux condenser, dissolve 16 g. of sodium hydroxide pellets in 95 ml. of hot methyl alcohol. Add 49 g. of guanidine nitrate, stir the mixture at 50-65° for 15 minutes, and then cool to about 20°. Filter oflF the separated sodium nitrate and wash with two 12 ml. portions of methyl alcohol. Return the combined filtrates to the clean reaction flask, add 69 g. of sulphanilamide (Section IX,9) and stir at 50-55° for 15 minutes. Detach the reflux condenser and, with the aid of a still-head ( knee-tube ), arrange the apparatus for distillation from an oil bath with stirring about 100 ml. of methyl alcohol are recovered. Add 12 g. of pure cycZohexanol. Raise the temperature of the oil bath to 180-190° and continue the distillation. Reaction commences with the evolution of ammonia when the uiternal temperature reaches 145°. Maintain the... 

First the protected oligopeptide is coupled with polymer-bound nitrophenol by DCC. N"-Deblocking leads then to simultaneous cycliiation and detachment of the product from the polymer (M. Fridkin, 1965). Recent work indicates that high dilution in liquid-phase cycli-zation is only necessary, if the cyclization reaction is sterically hindered. Working at low temperatures and moderate dilution with moderately activated acid derivatives is the method of choice for the formation of macrocyclic lactams (R.F. Nutt, 1980). 

Cracked or detached liner. This is indieated by an inerease in an aeoustie meter reading and a large spread in exhaust temperature. 

In systems of LP the dynamic response to a temperature quench is characterized by a different mechanism, namely monomer-mediated equilibrium polymerization (MMEP) in which only single monomers may participate in the mass exchange. For this no analytic solution, even in terms of MFA, seems to exist yet [70]. Monomer-mediated equilibrium polymerization (MMEP) is typical of systems like poly(a-methylstyrene) [5-7] in which a reaction proceeds by the addition or removal of a single monomer at the active end of a polymer chain after a radical initiator has been added to the system so as to start the polymerization. The attachment/detachment of single monomers at chain ends is believed to be the mechanism of equilibrium polymerization also for certain liquid sulphur systems [8] as well as for self-assembled aggregates of certain dyes [9] where chain ends are thermally activated radicals with no initiators needed. 

Table 10.9 lists some common zinc anode alloys. In three cases aluminium is added to improve the uniformity of dissolution and thereby reduce the risk of mechanical detachment of undissolved anode material . Cadmium is added to encourage the formation of a soft corrosion product that readily crumbles and falls away so that it cannot accumulate to hinder dissolution. The Military Specification material was developed to avoid the alloy passivating as a result of the presence of iron . It later became apparent that this material suffered intergranular decohesion at elevated temperatures (>50°C) with the result that the material failed by fragmentation". The material specified by Det Norske Veritas was developed to overcome the problem the aluminium level was reduced under the mistaken impression that it produced the problem. It has since been shown that decohesion is due to a hydrogen embrittlement mechanism and that it can be overcome by the addition of small concentrations of titanium". It is not clear whether... 

Among the molecules, however, business is going on as usual. Iodine dissolves by the detachment of surface layer molecules from the iodine crystals. The rate at which this process occurs is fixed by the stability of the crystal (tending to hold the molecules in the surface layer) and the temperature (the thermal agitation tending to dislodge the molecules from their lattice positions). As the dissolving continues, the concentration of iodine molecules in the solution increases. 

After detachment of the flame from the wall and reduction of its width, three zones develop in the vessel parallel to each other a flame and burned gas zone and two zones (adjacent to the sidewalls), where no flame is present and where the gas temperatures are lower than behind the flame. All this happens in a field of very high centrifugal acceleration, which induces a free convection movement of the flame and the product zone behind it toward the... 

Enhanced thermal stability enlarges the areas of application of protein films. In particular it might be possible to improve the yield of reactors in biotechnological processes based on enzymatic catalysis, by increasing the temperature of the reaction and using enzymes deposited by the LB technique. Nevertheless, a major technical difficulty is that enzyme films must be deposited on suitable supports, such as small spheres, in order to increase the number of enzyme molecules involved in the process, thus providing a better performance of the reactor. An increased surface-to-volume ratio in the case of spheres will increase the number of enzyme molecules in a fixed reactor volume. Moreover, since the major part of known enzymatic reactions is carried out in liquid phase, protein molecules must be attached chemically to the sphere surface in order to prevent their detachment during operation. 

---