Tandem source

Figure 22-1 Mass spectrum showing natural isotopes of Pb observed as an impurity in brass. [From Y. Su, Y. Duan, and Z. Jin, Development and Evaluation of a Glow Discharge Microwave-Induced Plasma Tandem Source lor Time-ot-Fllght Mass Spectrometry," Anal. Chem. 3000, 72,5600.]...

Borer M. and Hieftje G. M. (1991) Tandem sources for atomic emission spectrometry, Spectrochim Acta Rev 14 463-486. 

Tandem sources for atomic emission spectrometry, Spectrochim Acta Rev 14 463-486. 

Success of sample introduction methods, such as LA, ETV or LC in combination with ICP-MS, is on account of tandem source mass spectrometry [71], Instead of one source being responsible for the vaporisation, atomisation and ionisation of the sample, these tasks are divided among two different sources (i) LA/ETV vaporisation (and atomisation) (ii) ICP (atomisation and) ionisation and (Hi) MS identification and quantification. 

Su, Y. X., Duan, Y. X., and Jin, Z. (2000) Development and evaluation of a glow discharge microwave-induced-plasma tandem source for time-of-flight mass spectrometry. Anal. Chem., 72, 5600. 

A photovoltaic (PV) solar power system is a complete electrical source that uses solar cells to directly convert light energy into electricity. The system can be self-contained and completely autonomous or it can work in tandem with other conventional fuel-based sources of power to offer robust power availabihty. 

The main advantages of the ms/ms systems are related to the sensitivity and selectivity they provide. Two mass analyzers in tandem significantly enhance selectivity. Thus samples in very complex matrices can be characterized quickly with Htde or no sample clean-up. Direct introduction of samples such as coca leaves or urine into an ms or even a gc/lc/ms system requires a clean-up step that is not needed in tandem mass spectrometry (28,29). Adding the sensitivity of the electron multiplier to this type of selectivity makes ms/ms a powerhil analytical tool, indeed. It should be noted that introduction of very complex materials increases the frequency of ion source cleaning compared to single-stage instmments where sample clean-up is done first. 

Consider a distribution system as illustrated in Figure 27.13(a) being fed by two power sources in tandem ... 

The top and the bottom x-ray detector each contain a multiplier phototube coated with phosphor. This tube compares the intensity of the x-ray beam entering the detector with that of the light from the reference standard, a discharge lamp. The reference beam is part of a circuit that maintains the x-ray source at constant intensity. The deviation wedge comes to rest when the intensities of the transmitted x-ray beams stand in a predetermined ratio. At this point, the unbalance in the servo system has been compensated, and the position of the deviation wedge consequently indicates the thickness of the strip. In 1955, this application was made fully automatic that is, the unbalance (or error signal) just mentioned was used to readjust tandem cold reduction mills of the United States Steel Corporation. Automatic control proved significantly more effective than manual control. 

The ionization techniques most widely used for LC-MS, however, are termed soft ionization in that they produce primarily molecular species with little fragmentation. It is unlikely that the molecular weight alone will allow a structural assignment to be made and it is therefore desirable to be able to generate structural information from such techniques. There are two ways in which this may be done, one of which, the so-called cone-voltage or in-source fragmentation, is associated specifically with the ionization techniques of electiospray and APCl and is discussed later in Section 4.7.4. The other, termed mass spectrometry-mass spectrometry (MS-MS) or tandem mass spectrometry, is applicable to all forms of ionization, provided that appropriate hardware is available, and is described here. 

Several other interface designs were introduced over this period, including continuous flow fast atom bombardment (CFFAB)" and the particle beam interface (PBI)," but it was not until the introduction of the API source that LC/MS applications really came to the forefront for quantitative analysis. Early work by Muck and Henion proved the utility of an atmospheric pressure interface using a tandem quadrupole mass spectrometer. 

Several examples of conjugate addition of carbanions carried out under aprotic conditions are given in Scheme 2.24. The reactions are typically quenched by addition of a proton source to neutralize the enolate. It is also possible to trap the adduct by silylation or, as we will see in Section 2.6.2, to carry out a tandem alkylation. Lithium enolates preformed by reaction with LDA in THF react with enones to give 1,4-diketones (Entries 1 and 2). Entries 3 and 4 involve addition of ester enolates to enones. The reaction in Entry 3 gives the 1,2-addition product at —78°C but isomerizes to the 1,4-product at 25° C. Esters of 1,5-dicarboxylic acids are obtained by addition of ester enolates to a,(3-unsaturated esters (Entry 5). Entries 6 to 8 show cases of... 

---