Take-all

Taking all these conditions into account the estimation for the minimal thickness difference of steel which could be perceptible at granularity levels equal to the limiting values for granularity in EN 584-1 results in the values given in Table 1. 

Under the New Approach Member States shall not prohibit, restrict or impede the placing on the market or putting into service of products which comply with the directives and bear the CE-marking. Member States have also the obligation to take all appropriate measures to ensure that the products placed on the market do not endanger the health and safety of persons. 

Where a Member State ascertains tliat a product, bearing the CE-marking and used in accordance with its intended use, is liable to endanger the safety of persons or health, it shall take all appropriate measures to withdraw such a product from the market. That Member State shall immediately Inform the Commission which is obliged to investigate whether or not the measure is justified. Where the Commission considers that the measure is justified, it shall immediately inform the Member State which took the initiative and also the other Member States. This entails that the other Member States must also take action against the product concerned. That latter disposition is referred to as the safeguard clause. 

The final total ion time of flight in the TOF mass spectrometer with a single accelerating region can be written in a smgle equation, taking all of the above factors into account. 

As the number of conformations increases exponentially with the number of rotatable bonds, for most molecules it is not feasible to take all possible conformations into account. However, a balanced sampling of the conformational space should be ensured if only subsets arc being considered. In order to restrict the number of geometries output, while retaining a maximum of conformational diversity, ROTATE offers the possibility of classifying the remaining conformations, i.c., similar conformations can be combined into classes. The classification is based on the RMS deviation between the conformations, either in Cartesian (RMS y 7if [A]) or torsion space in [ ], The RMS threshold, which decides whether two... 

Some systems can give quantitative results from known pieces of data complete with proper units. For example, these systems can take all the starting information and then determine a set of equations from the available list that can yield the desired result. The program could subsequently convert units or algebraically solve the equations if necessary. 

Taking all of the above into account, it can be shown that the efficiency, Tj, of a thermoelectric power generator, neglecting Thomson heat, is given by... 

Two important facets of these functions should be recognized. First, the sin z is unbounded and, second, e takes all complex values except 0. 

They must take all reasonable steps to ensure waste is collected, treated, transported and disposed of by licensed operators. 

These are the main steps of design methodology. In some cases all the steps are not needed, but in most cases it is important to take all of them into consideration. In addition to the construction and the use of the system,... 

Bonded-bolted joints have good load distribution and are generally designed so that the bolts take all the load. Then, the bolts would take all the load after the bond breaks (because the bolts do not receive load until the bond slips). The bond provides a change in failure mode and a sizable margin against fatigue failure. 

Now Now cried the Queen. Faster Faster . . . Now here, you see, it takes all the running you can do, to keep in the same place. If you want to get somewhere else, you must run at least twice as fast as that ... 

And what if the basis functions are centred on different atoms The CNDO solution to the problem is to take all possible integrals such as those above to be equal, and to assume that they depend only on the atoms A and B on which the basis functions are centred. This satisfies the rotational invariance requirement. In CNDO theory, we write the two-electron integrals as pab and they are taken to have the same value irrespective of the basis functions on atom A and/or atom B. They are usually calculated exactly, but assuming that the orbital in question is a Is orbital (for hydrogen) or a 2s orbital (for a first row atom). 

In considering Ian performance, it is incorrect to calculate a change for one characteristic and ignore the others in the Fan Law Group, because it takes all three characteristics to properly define the operational point of the fan. 

Work, etc. Act 1974 an employer has to take all steps, as far as is reasonably practicable, to ensure the health, safety and welfare of his workers. Permissible noise levels are defined by codes of practice, and the figure permitted for employee exposure is 90dB(A) 8-hour Leq. 

There are in addition several other factors that accelerate corrosion and must betaken into account these include crevices, galvanic coupling, tensile stress, aeration, presence of impurities, surface finish, etc. If these were also taken into consideration then several million experiments would have to be performed to compile such data. There are many instances where two or more chemicals exert a marked synergistic action such that low dissolution rates obtained in either environment become much greater in the presence of both. Further, the corrosiveness of a chemical will be affected by the presence of certain impurities, which may act as either accelerators or inhibitors. To take all these factors into account would add to an already impossible task and as Evans has remarked, There are not enough trained investigators in the world to obtain the empirical information to cover all combinations of conditions likely to arise . Unfortunately corrosion science has not yet reached the stage where prediction, based on a few well established laws, allows selection of materials to be made without recourse to a vast amount of data. 

Open recirculating systems These are more amenable to inhibition since it is possible to maintain a closer control on water composition. Corrosion inhibition in these systems is closely allied to a number of other problems that have to be considered in the application of water treatment. Most of these arise from the use of cooling towers, ponds, etc. in which the water is subject to constant evaporation and contamination leading to accumulation of dirt, insoluble matter, aggressive ions and bacterial growths, and to variations in pH. A successful water treatment must therefore take all these factors into account and inhibition will often be accompanied by scale prevention and bactericidal treatments. 

Where heat is conducted through a plane solid which is between two fluids, there will he the convective resistances at the surfaces. The overall heat transfer must take all of these resistances into account, and the unit transmittance, or U factor, is given hy ... 

Taking all the sequence rules into account, we can assign the configurations shown in the following examples. Work through each one to convince yourself that the assignments are correct. 

Take all the mineral salts there are, also all salts of animal and vegetable origin. Add all the metals and minerals, omitting none. 

The choice of a satisfactory chelating agent for a particular separation should, of course, take all the above factors into account. The critical influence of pH on the solvent extraction of metal chelates is discussed in the following section. 

Many injection molded products will influence the final product s performance, dimensions, and other characteristics. The mold includes the cavity shape, gating, parting line, vents, undercuts, ribs, hinges, and so on (Table 3-17). The mold designer must take all these factors into account to eliminate problems. At times, to provide the best design... 

Taking all the constants into one super constant, K, and incorporating the result of equation (6.9), we have... 

As the starting geometries for iterative calculation, we take all the possible structures in which bond lengths are distorted so that the set of displacement vectors may form a basis of an irreducible representation of the full symmetry group of a molecule. For example, with pentalene (I), there are 3, 2, 2 and 2 distinct bond distortions belonging respectively to a, b2 and representations of point group D21,. 

Taking all of these results together, some general patterns emerge. Foremost, the tetrahedral adducts 1 are found to be energy minima when the substituents X and Y are both first-row elements. However, when X and Y are both second-row elements, the tetrahedral species is a transition state and the only minima are ion-dipole complexes, 1. Clearly, two key factors in the formation of the tetrahedral adduct 1 are the difference in gas-phase basicities for the two anions (X" and 1) and the difference... 

IZ. children eatin0 pacKed lunches must taKe all their litter home with them. 

---