Stripping example

The simplest way to visualize internal stresses is by observing the distortions that accompany them, as in the bimetallic strip example above. For example, coating a resin adhesive on to a strip of plastic film (Fig. la) and then polymerizing it, causes bending of the composite strip (Fig. lb) as a result of polymerization shrinkage in the adhesive layer. 

Isopropyl Alcohol Stripping Example. In the manufacture of isopropyl alcohol, propylene is dissolved in sulfuric acid to give an extract of mono-isopropyl sulfate. To avoid excessive decomposition this extract must be diluted until the ratio... 

Composition is normally expressed by a distillation curve, and can be supplemented by compositional analyses such as those for aromatics content. Some physical properties such as density or vapor pressure are often added. The degree of purity is indicated by color or other appropriate test (copper strip corrosion, for example). 

Performance can be illustrated for example by the time necessary for deaeration or de-emulsification of oils, anti-rust properties, copper strip corrosion test, the flash point in closed or open cup, the cloud and pour points, the foaming characteristics, etc. 

With practice writing structural formulas for organic molecules soon becomes rou tine and can be simplified even more For example a chain of carbon atoms can be rep resented by drawing all of the C—C bonds while omitting individual carbons The result mg structural drawings can be simplified still more by stripping away the hydrogens... 

Anodic stripping voltammetry consists of two steps (Figure 11.37). The first is a controlled potential electrolysis in which the working electrode, usually a hanging mercury drop or mercury film, is held at a cathodic potential sufficient to deposit the metal ion on the electrode. For example, with Cu + the deposition reaction is... 

Representative Examples of Analytes Determined by Stripping Voltammetry... 

In adsorptive stripping voltammetry the deposition step occurs without electrolysis. Instead, the analyte adsorbs to the electrode s surface. During deposition the electrode is maintained at a potential that enhances adsorption. For example, adsorption of a neutral molecule on a Hg drop is enhanced if the electrode is held at -0.4 V versus the SCE, a potential at which the surface charge of mercury is approximately zero. When deposition is complete the potential is scanned in an anodic or cathodic direction depending on whether we wish to oxidize or reduce the analyte. Examples of compounds that have been analyzed by absorptive stripping voltammetry also are listed in Table 11.11. 

Sensitivity In many voltammetric experiments, sensitivity can be improved by adjusting the experimental conditions. For example, in stripping voltammetry, sensitivity is improved by increasing the deposition time, by increasing the rate of the linear potential scan, or by using a differential-pulse technique. One reason for the popularity of potential pulse techniques is an increase in current relative to that obtained with a linear potential scan. 

Polymerizations are typically quenched with water, alcohol, or base. The resulting polymerizates are then distilled and steam and/or vacuum stripped to yield hard resin. Hydrocarbon resins may also be precipitated by the addition of the quenched reaction mixture to an excess of an appropriate poor solvent. As an example, aUphatic C-5 resins are readily precipitated in acetone, while a more polar solvent such as methanol is better suited for aromatic C-9 resins. 

Three generations of latices as characterized by the type of surfactant used in manufacture have been defined (53). The first generation includes latices made with conventional (/) anionic surfactants like fatty acid soaps, alkyl carboxylates, alkyl sulfates, and alkyl sulfonates (54) (2) nonionic surfactants like poly(ethylene oxide) or poly(vinyl alcohol) used to improve freeze—thaw and shear stabiUty and (J) cationic surfactants like amines, nitriles, and other nitrogen bases, rarely used because of incompatibiUty problems. Portiand cement latex modifiers are one example where cationic surfactants are used. Anionic surfactants yield smaller particles than nonionic surfactants (55). Often a combination of anionic surfactants or anionic and nonionic surfactants are used to provide improved stabiUty. The stabilizing abiUty of anionic fatty acid soaps diminishes at lower pH as the soaps revert to their acids. First-generation latices also suffer from the presence of soap on the polymer particles at the end of the polymerization. Steam and vacuum stripping methods are often used to remove the soap and unreacted monomer from the final product (56). 

Chemical Separation. A reprocessing facility typically utilizes multiple extraction/reextraction (stripping) cycles for the recovery and purification of uranium and plutonium. For example, a co-decontamination and partitioning cycle is followed by one or more cycles of uranium and plutonium purification. The basic process is illustrated in Figure 3. 

For any nucHde that decays only by this electron capture process, if one were to produce an atom in which all of the electrons were removed, the effective X would become infinite. An interesting example of this involves the decay of Mn in interstellar space. For its normal electron cloud, Mn decays with a half-life of 312 d and this decay is by electron capture over 99.99% of the time. The remaining decays are less than 0.0000006% by j3 -decay and a possible branch of less than 0.0003% by /5 -decay. In interstellar space some Mn atoms have all of their electrons stripped off so they can only decay by these particle emissions, and therefore their effective half-life is greater than 3 x 10 yr. 

A sequence of tests has been devised to evaluate antioxidants for use in automotive crankcase lubricants. The Indiana Stirring Oxidation Test (ISOT) JISK2514 is an example of a laboratory screening test. The oil is stirred at 165.5°C in the presence of air. Copper and iron strips are used as metal catalysts. The development of sludge, viscosity, and acidity are deterrnined periodically. Failure time is determined when the development of acidity requires... 

---