Stress corrosion cracking composition

Single-phase a-brasses are susceptible to stress-corrosion cracking in the presence of moist ammonia vapour or certain ammonium compounds Here the predominant metallurgical variable is alloy composition, and in... 

In practice, by far the most common case of stress corrosion is that occurring when austenitic stainless steels are simultaneously exposed to tensile stresses and hot, aqueous, aerated, chloride-containing environments. In this case the major variable is alloy composition and structure virtually all austenitic stainless steels are more or less susceptible to stress-corrosion cracking in these environments, while ferritic and ferritic/austenitic stainless steels are highly resistant or immune. 

The high strength alloys contain a Zn + Mg content well in excess of 6% and are used in specialist structures such as aircraft. The risk of stress corrosion cracking in these alloys may be accentuated by incorrect heat treatment or composition and they cannot be recommended for general use (Section 8.5). 

However, whilst the effects of change in alloy composition upon stress-corrosion cracking susceptibility in the present context may be partly due to their effect upon stacking-fault energy, this does not constitute a complete explanation, since alloying may have significant effects upon electrochemical parameters. The effect of the zinc content of brasses upon their filming characteristics has already been mentioned, while in more recent... 

The fracture mode of stress-corrosion cracks in austenitic stainless steels can be transgranular, intergranular or a mixture of both. One of the earliest environments found to cause problems was solutions containing chlorides or other halides and the data due to Copson (Fig. 8.30) is very informative. The test solution for that data was magnesium chloride at 154°C the alloys contained 18-20alloy with a composition of approximately 18Cr-8Ni has the least resistance to cracking in this environment. 

In addition to the alloy compositions being of importance with regard to susceptibility to stress-corrosion cracking, the resistance of the alloy can be altered by microstructural factors. Hanninen has reviewed the available literature quite thoroughly and has concluded that a fine grain size is likely to be beneficial. Strain imposed prior to use tends to be deleterious because deformed material usually acts anodic with respect to unstrained material and because the introduction of plastic deformation may also... 

Stress-corrosion cracking occurs in certain aluminium alloys which have been developed for medium and high strength by employing variations in composition, cold work and heat treatment The main alloys are based upon Al-Mg, Al-Mg and Al-Cu, but stress corrosion also occurs in Al-Ag, Al-Cu-Mg, Al-Mg-Si, Al-Zn and Al-Cu-Mg-Zn alloys. It has... 

In more recent work embrittlement in water vapour-saturated air and in various aqueous solutions has been systematically examined together with the influence of strain rate, alloy composition and loading mode, all in conjunction with various metallographic techniques. The general conclusion is that stress-corrosion crack propagation in aluminium alloys under open circuit conditions is mainly caused by hydrogen embrittlement, but that there is a component of the fracture process that is caused by dissolution. The relative importance of these two processes may well vary between alloys of different composition or even between specimens of an alloy that have been heat treated differently. 

Early use of the test was in providing data whereby the effects of such variables as alloy composition and structure or inhibitive additions to cracking environments could be compared, and also for promoting stress-corrosion cracking in combinations of alloy and environment that could not be caused to fail in the laboratory under conditions of constant load or... 

Marine fouling leading to the local production of HjS increases crack growth rate, but what the effect is when combined with CP is uncertain. Some of the factors mentioned earlier in connection with other steel corrosion problems are important to sulphide stress-corrosion cracking, (SSCC), eg. compositions, particularly C which usefully can be reduced to below 0.05%, S, microstructure and segregation . Compositional homogenisation by heat treatment can be beneficial ", whilst the presence of Cu in the... 

Exchangers failed after two weeks operation due to high chloride content of coohng water, causing stress-corrosion cracking of 304 stainless steel. lOne application failed due to unanticipated composition variations. Relatively low unprotected rate did not provide incentive for further work. 

---