Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Strength foams

H.W. Guo, Y.X. Gong, S.Y. Gao, Preparation of high strength foam glass-ceramics from waste... [Pg.125]

Superabsorbents. Water-sweUable polymers are used extensively in consumer articles and for industrial appUcations. Most of these polymers are cross-linked acryUc copolymers of metal salts of acryUc acid and acrylamide or other monomers such as 2-acrylamido-2-methylpropanesulfonic acid. These hydrogel forming systems can have high gel strength as measured by the shear modulus (134). Sometimes inorganic water-insoluble powder is blended with the polymer to increase gel strength (135). Patents describe processes for making cross-linked polyurethane foams which contain superabsorbent polymers (136,137). [Pg.144]

Density and polymer composition have a large effect on compressive strength and modulus (Fig. 3). The dependence of compressive properties on cell size has been discussed (22). The cell shape or geometry has also been shown important in determining the compressive properties (22,59,60,153,154). In fact, the foam cell stmcture is controlled in some cases to optimize certain physical properties of rigid cellular polymers. [Pg.412]

Strengths and moduli of most polymers increase as the temperature decreases (155). This behavior of the polymer phase carried over into the properties of polymer foams and similar dependence of the compressive modulus of polyurethane foams on temperature has been shown (151). [Pg.412]

Tensile strength and modulus of rigid foams have been shown to vary with density in much the same manner as the compressive strength and modulus. General reviews of the tensile properties of rigid foams are available (22,59,60,131,156). [Pg.412]

Those stmctural variables most important to the tensile properties are polymer composition, density, and cell shape. Variation with use temperature has also been characterized (157). Flexural strength and modulus of rigid foams both increase with increasing density in the same manner as the compressive and tensile properties. More specific data on particular foams are available from manufacturers Hterature and in References 22,59,60,131 and 156. Shear strength and modulus of rigid foams depend on the polymer composition and state, density, and cell shape. The shear properties increase with increasing density and with decreasing temperature (157). [Pg.412]

Tensile Strength and Elongation. The tensile strength of latex mbber foam has been shown to depend on the density of the foam (149,177) and on the tensile strength of the parent mbber (177,178). At low densities the tensile modulus approximates a linear relation with density but kicreases with a higher power of density at higher densities. Similar relations hold for polyurethane and other flexible foams (156,179,180). [Pg.413]

Tear Strength. A relation for the tearkig stress of flexible foams that predicts linear kicrease ki the tearkig energy with density and kicreased tearkig energy with cell size has been developed (177). Both relationships are verified to a limited extent by experimental data. [Pg.413]

The combination of stmctural strength and flotation has stimulated the design of pleasure boats using a foamed-in-place polyurethane between thin skins of high tensUe strength (231). Other ceUular polymers that have been used in considerable quantities for buoyancy appHcations are those produced from polyethylene, poly(vinyl chloride), and certain types of mbber. The susceptibUity of polystyrene foams to attack by certain petroleum products that are likely to come in contact with boats led to the development of foams from copolymers of styrene and acrylonitrUe which are resistant to these materials... [Pg.416]

Electrical Insulation. The substitution of a gas for part of a soHd polymer usuaUy results in large changes in the electrical properties of the resulting material. The dielectric constant, dissipation factor, and dielectric strength are aU generaUy lowered in amounts roughly proportional to the amount of gas in the foam. [Pg.416]

Mechanical Properties and Structural Performance. As a result of the manufacturing process, some cellular plastics have an elongated cell shape and thus exhibit anisotropy in mechanical, thermal, and expansion properties (35,36). Efforts are underway to develop manufacturing techniques that reduce such anisotropy and its effects. In general, higher strengths occur for the paraHel-to-rise direction than in the perpendicular-to-rise orientation. Properties of these materials show variabiUty due to specimen form and position in the bulk material and to uncertainty in the axes with respect to direction of foam rise. Expanded and molded bead products exhibit Httie anisotropy. [Pg.335]

Polyurethane, PVC, and extruded polystyrene provide the bulk of the cellular plastics used for low and cryogenic temperature appHcations. In some cases, eg, the insulation of Hquid hydrogen tanks on space systems, foams have been reinforced with continuous glass fibers throughout the matrix. This improves strength without affecting thermal performance significantly. [Pg.336]

High temperature steam cools and eventually condenses as it propagates through the oil reservoir. To maintain foam strength as the steam cools, a noncondensible gas, usually nitrogen or methane, is often added to the injectant composition (196). Methods of calculating the optimum amount of noncondensible gas to use are available (197). [Pg.193]

A mixture of PhenoHc MicrobaUoons and resin binder has a putty-like consistency. It can be molded to shape, troweUed onto surfaces, or pressed into a core. Curing gives a high strength, low density (0.144 g/cm ) foam free of voids and dense areas, and without a brittle skin. Syntactic foams are used in widely diverse appHcations, including boat flotation aids stmctural parts in aircraft, submarines, and missiles stmctural cores for waU panels and ablative heat shields for reentry vehicles and rocket test engines. [Pg.308]


See other pages where Strength foams is mentioned: [Pg.210]    [Pg.186]    [Pg.317]    [Pg.364]    [Pg.46]    [Pg.299]    [Pg.299]    [Pg.112]    [Pg.82]    [Pg.210]    [Pg.186]    [Pg.317]    [Pg.364]    [Pg.46]    [Pg.299]    [Pg.299]    [Pg.112]    [Pg.82]    [Pg.79]    [Pg.197]    [Pg.206]    [Pg.412]    [Pg.24]    [Pg.378]    [Pg.368]    [Pg.403]    [Pg.406]    [Pg.406]    [Pg.407]    [Pg.412]    [Pg.413]    [Pg.413]    [Pg.413]    [Pg.416]    [Pg.418]    [Pg.431]    [Pg.121]    [Pg.332]    [Pg.332]    [Pg.409]    [Pg.4]    [Pg.174]    [Pg.193]    [Pg.193]    [Pg.308]    [Pg.308]   
See also in sourсe #XX -- [ Pg.273 ]




SEARCH



Tensile strength examples versus density of Polypropylene foams

Tensile strength versus density for PE foam example

© 2024 chempedia.info