Spectrometer atomic

D Commercial COTS controlled by external computer Hybrid systems such as automated dissolution workstation with high-performance liquid chromatography (HPLC) or ultraviolet-visible (UV-Vis) interface Liquid chromatographs, gas chromatographs, UV/Vis spectrophotometers, Fourier transform infrared (FTIR) spectrophotometers, near-infrared (NIR) spectrophotometers, mass spectrometers, atomic absorption spectrometers, thermal gravimetric analyzers, COTS automation workstations... 

Isotopes Most elements are composed of a mixture of isotopes. These will be separated in a mass spectrometer. Atoms or molecules containing such elements will display a cluster of ions reflecting the isotopic composition. 

Vollkopf, U. Giinsel, A. and Janssen A. (1990) Use of flow injection techniques for the analysis of hydride-forming elements with the Perkin-Elmer Sciex ELAN 500 ICP-Mass spectrometer. Atom. Spectrosc., 11.135-137. 

By using a simple mass spectrometer, EWAston discovered that all atoms of a particular element do not have the same mass. In the Mass Spectrometer, atoms arc given a charge and accelerated in an electric field so that they move at high... 

To monitor their surface plasmon absorption, UV-visible absorption spectra were obtained for all LbL films produced using a Cary 50 UV-visible spectrometer. Atomic force microscopy (AFM) measurements were performed on a Digital Instruments NanoScope IV operating in tapping mode with a n+-... 

A connnon feature of all mass spectrometers is the need to generate ions. Over the years a variety of ion sources have been developed. The physical chemistry and chemical physics communities have generally worked on gaseous and/or relatively volatile samples and thus have relied extensively on the two traditional ionization methods, electron ionization (El) and photoionization (PI). Other ionization sources, developed principally for analytical work, have recently started to be used in physical chemistry research. These include fast-atom bombardment (FAB), matrix-assisted laser desorption ionization (MALDI) and electrospray ionization (ES). 

The absolute measurement of areas is not usually usefiil, because tlie sensitivity of the spectrometer depends on factors such as temperature, pulse length, amplifier settings and the exact tuning of the coil used to detect resonance. Peak intensities are also less usefiil, because linewidths vary, and because the resonance from a given chemical type of atom will often be split into a pattern called a multiplet. However, the relative overall areas of the peaks or multiplets still obey the simple rule given above, if appropriate conditions are met. Most samples have several chemically distinct types of (for example) hydrogen atoms within the molecules under study, so that a simple inspection of the number of peaks/multiplets and of their relative areas can help to identify the molecules, even in cases where no usefid infonnation is available from shifts or couplings. 

K, L, M,. ..), 5 is the energy shift caused by relaxation efiects and cp is the work fimction of tlie spectrometer. The 5 tenn accounts for the relaxation effect involved in the decay process, which leads to a final state consisting of a heavily excited, doubly ionized atom. 

Ar, Cs, Ga or other elements with energies between 0.5 and 10 keV), energy is deposited in the surface region of the sample by a collisional cascade. Some of the energy will return to the surface and stimulate the ejection of atoms, ions and multi-atomic clusters (figure Bl.25.8). In SIMS, secondary ions (positive or negative) are detected directly with a mass spectrometer. 

If the molecules could be detected with 100% efficiency, the fluxes quoted above would lead to impressive detected signal levels. The first generation of reactive scattering experiments concentrated on reactions of alkali atoms, since surface ionization on a hot-wire detector is extremely efficient. Such detectors have been superseded by the universal mass spectrometer detector. For electron-bombardment ionization, the rate of fonnation of the molecular ions can be written as... 

Schematic diagram of a muitichannei atomic emission spectrometer, showing the arrangement of muitipie exit siits and detectors for the simuitaneous anaiysis of severai eiements.

A gun is used to direct a beam of fast-moving atoms or ions onto the liquid target (matrix). Figure 4.1 shows details of the operation of an atom gun. An inert gas is normally used for bombardment because it does not produce unwanted secondary species in the primary beam and avoids contaminating the gun and mass spectrometer. Helium, argon, and xenon have been used commonly, but the higher mass atoms are preferred for maximum yield of secondary ions. 

Instead of the fast-atom beam, a primary ion-beam gun can be used in just the same way. Generally, such an ion gun emits a stream of cesium ions (Cs ), which are cheaper to use than xenon but still have large mass (atomic masses Cs, 139 Xe, 131). Although ion guns produce no fragment ions in the primary beam, they can contaminate the mass spectrometer by deposition with continued use. 

The basic principles of fast-atom bombardment (FAB) and liquid-phase secondary ion mass spectrometry (LSIMS) are discussed only briefly here because a fuller description appears in Chapter 4. This chapter focuses on the use of FAB/LSIMS as part of an interface between a liquid chromatograph (LC) and a mass spectrometer (MS), although some theory is presented. 

Liquids examined by FAB are introduced into the mass spectrometer on the end of a probe inserted through a vacuum lock in such a way that the liquid lies in the target area of the fast atom or ion beam. There is a high vacuum in this region, and there would be little point in attempting to examine a solution of a sample in one of the commoner volatile solvents such as water or dichloromethane because it would evaporate extremely quickly, probably as a burst of vapor when introduced into the vacuum. Therefore it is necessary to use a high-boiling solvent as the matrix material, such as one of those listed in Table 13.1. 

By passing a continuous flow of solvent (admixed with a matrix material) from an LC column to a target area on the end of a probe tip and then bombarding the target with fast atoms or ions, secondary positive or negative ions are ejected from the surface of the liquid. These ions are then extracted into the analyzer of a mass spectrometer for measurement of a mass spectrum. As mixture components emerge from the LC column, their mass spectra are obtained. 

If a sample solution is introduced into the center of the plasma, the constituent molecules are bombarded by the energetic atoms, ions, electrons, and even photons from the plasma itself. Under these vigorous conditions, sample molecules are both ionized and fragmented repeatedly until only their constituent elemental atoms or ions survive. The ions are drawn off into a mass analyzer for measurement of abundances and mJz values. Plasma torches provide a powerful method for introducing and ionizing a wide range of sample types into a mass spectrometer (inductively coupled plasma mass spectrometry, ICP/MS). 

---