Solvents block copolymers

A brief review has appeared covering the use of metal-free initiators in living anionic polymerizations of acrylates and a comparison with Du Font s group-transfer polymerization method (149). Tetrabutylammonium thiolates mn room temperature polymerizations to quantitative conversions yielding polymers of narrow molecular weight distributions in dipolar aprotic solvents. Block copolymers are accessible through sequential monomer additions (149—151) and interfacial polymerizations (152,153). 

Solvents influence the rate of free-radical homopolymerization of acrylic acid and its copolymerization with other monomers. Hydrogen-bonding solvents slow down the reaction rates. Due to the electron-withdrawing nature of the ester groups, acrylic and methacrylic ester polymerize by anionic but not by cationic mechanisms. Lithium alkyls are very effective initiators of a-methyl methacrylate polymerization yielding stereospecific polymers.Isotactic poly(methyl methacrylate) forms in hydrocarbon solvents. Block copolymers of isotactic and syndiotactic poly(methyl methacrylate) form in solvents of medium polarity. Syndiotactic polymers form in polar solvents, like ethylene glycol dimethyl ether, or pyridine. This solvent influence is related to Lewis basicity in the following order ... 

In a solvent, block copolymer phase behavior is controlled by the interaction between the segments of the polsrmers and the solvent molecules as well as the interaction between the segments of the two blocks. If the solvent is unfavorable for one block, this can lead to micelle formation in dilute solution. The phase behavior of concentrated solutions can be mapped onto that of block copolymer melts (97). Lamellar, hexagonal-packed cylinder, micellar cubic, and bicontinu-ous cubic structures have all been observed (these are all lyotropic liquid crystal phases, similar to those observed for nonionic surfactants). This is illustrated by representative phase diagrams for Pluronic triblocks in Figure 6. 

Several less common monomers have been polymerized anionically. Ree and Minoura" effected the conversion of aminoacetonitrile to NHCH2C(NH) n— by treatment with sodium s-butoxide in dioxan hydrolysis yielded the polypeptide—[NHCHaCO] —. Aminopropionitrile behaved similarly. High polymer has been formed from 8-nitrostyrene using alkoxide ion as initiator in protic solvents. Block copolymer is formed from polyisoprenylpotassium in benzene on adding 1-nitropropene. Vinyl ferrocene has been shown to undergo homo- and co-polymerization by butyl-lithium or lithium metal, but the utility of these synthetic procedures is severely limited by side reactions. The poly-... 

Pressure sensitive adhesives typically employ a polymer, a tackifier, and an oil or solvent. Environmental concerns are moving the PSA industry toward aqueous systems. Polymers employed in PSA systems are butyl mbber, natural mbber (NR), random styrene—butadiene mbber (SBR), and block copolymers. Terpene and aUphatic resins are widely used in butyl mbber and NR-based systems, whereas PSAs based on SBR may require aromatic or aromatic modified aUphatic resins. 

Other Uses. Large quantities of hydrocarbon resins are used in mastics, caulks, and sealants (qv). Polymers for these adhesive products include neoprene, butyl mbber, polyisoprene, NR, SBR, polyisobutylene, acryHcs, polyesters, polyamides, amorphous polypropylene, and block copolymers. These adhesives may be solvent or water-borne and usually contain inorganic fillers. 

Nonaqueous Dispersion Polymerization. Nonaqueous dispersion polymers are prepared by polymerizing a methacryhc monomer dissolved in an organic solvent to form an insoluble polymer in the presence of an amphipathic graft or block copolymer. This graft or block copolymer, commonly called a stabilizer, lends coUoidal stabiUty to the insoluble polymer. Particle sizes in the range of 0.1—1.0 pm were typical in earlier studies (70), however particles up to 15 pm have been reported (71). 

Depending on the concentration, the solvent, and the shear rate of measurement, concentrated polymer solutions may give wide ranges of viscosity and appear to be Newtonian or non-Newtonian. This is illustrated in Eigure 10, where solutions of a styrene—butadiene—styrene block copolymer are Newtonian and viscous at low shear rates, but become shear thinning at high shear rates, dropping to relatively low viscosities beyond 10 (42). The... 

Block copolymers of vinyl acetate with methyl methacrylate, acryflc acid, acrylonitrile, and vinyl pyrrohdinone have been prepared by copolymeriza tion in viscous conditions, with solvents that are poor solvents for the vinyl acetate macroradical (123). Similarly, the copolymeriza tion of vinyl acetate with methyl methacrylate is enhanced by the solvents acetonitrile and acetone and is decreased by propanol (124). Copolymers of vinyl acetate containing cycHc functional groups in the polymer chain have been prepared by copolymeriza tion of vinyl acetate with A/,A/-diaIlylcyanamide and W,W-diaIl5lamine (125,126). 

Commercially, anionic polymerization is limited to three monomers styrene, butadiene, and isoprene [78-79-5], therefore only two useful A—B—A block copolymers, S—B—S and S—I—S, can be produced direcdy. In both cases, the elastomer segments contain double bonds which are reactive and limit the stabhity of the product. To improve stabhity, the polybutadiene mid-segment can be polymerized as a random mixture of two stmctural forms, the 1,4 and 1,2 isomers, by addition of an inert polar material to the polymerization solvent ethers and amines have been suggested for this purpose (46). Upon hydrogenation, these isomers give a copolymer of ethylene and butylene. 

---