Side reactions. blocking

A metabolic engineering approach [175] and directed evolution techniques [176] were evaluated to avoid side reactions, block degradative pathways, and enhance the desired reaction (conversion of indene to cxs-amino indanol 137 or ds-indanediol). Multiparameter flow cytometry was used to assess indene toxicity, and it was shown that concentrations up to 025 g/1 of indene (0.037g indene per gram dry cell wt.) in batch bioconversions did not influence reaction rate. Using this information, a single-phase... 

Significant quantities of the diphenoquinone are also produced if the ortho substituents are methoxy groups (36). Phenols with less than two ortho substituents produce branched and colored products from the reactions that occur at the open ortho sites. It is possible to minimize such side reactions in the case of o-cresol oxidation by using a bulky ligand on the copper catalyst to block the open ortho position (38). 

One-part urethane sealants (Table 3) are more compHcated to formulate on account of an undesirable side reaction between the prepolymer s isocyanate end and water vapor which generates carbon dioxide. If this occurs, the sealant may develop voids or bubbles. One way to avoid this reaction is to block the isocyanate end with phenol and use a diketamine to initiate cure. Once exposed to moisture, the diketamine forms a diamine and a ketone. The diamine reacts with the isocyanate end on the prepolymer, creating a cross-link (10). Other blocking agents, such as ethyl malonate, are also used (11). Catalysts commonly used in urethane formulations are tin carboxylates and bismuth salts. Mercury salt catalysts were popular in early formulations, but have been replaced by tin and bismuth compounds. 

W-(Methoxycarbonyl)triphenylphosphine imide reacts with methyl trifluoro-pyruvate to form methyl A -methoxycarbonyl 2 immo-3,3,3 trifluoropropionate m 95% yield This convenient building block easily adds nucleophiles such as Gngnard reagents without competing side reactions at the ester group to form trifluoromethylated amino acids [J.S] (equation 31)... 

Catalyst films used in electrochemical promotion (NEMCA) studies are usually prepared by using commercial metal pastes. Unfluxed pastes should be used, as fluxes may introduce unwanted side reactions or block electrocatalytic and catalytic sites. This action may obscure or even totally inhibit the electrochemical promotion effect. 

Block one side of the ketone by introducing a removable group. Alkylation takes place on the other side the blocking group is then removed. A common reaction for this purpose is formylation with ethyl formate (10-119) this generally blocks the less hindered side. The formyl group is easily removed by alkaline hydrolysis (12-41). 

In summary, we have examined several new methods for cleaving ester groups in poly(styrene-b-alkyl methacrylates). Short blocks of methyl methacrylate are very difficult to hydrolyze, but can be cleaved with reagents such as lithium iodide and potassium trimethylsilanolate. These latter reagents, however, result in side-reactions which appear to crosslink the polymer. 

The most studied catalyst family of this type are lithium alkyls. With relatively non-bulky substituents, for example nBuLi, the polymerization of MMA is complicated by side reactions.4 0 These may be suppressed if bulkier initiators such as 1,1-diphenylhexyllithium are used,431 especially at low temperature (typically —78 °C), allowing the synthesis of block copolymers.432,433 The addition of bulky lithium alkoxides to alkyllithium initiators also retards the rate of intramolecular cyclization, thus allowing the polymerization temperature to be raised.427 LiCl has been used to similar effect, allowing monodisperse PMMA (Mw/Mn = 1.2) to be prepared at —20 °C.434 Sterically hindered lithium aluminum alkyls have been used at ambient (or higher) temperature to polymerize MMA in a controlled way.435 This process has been termed screened anionic polymerization since the bulky alkyl substituents screen the propagating terminus from side reactions. 

---