Sample Volume and Maximum Extra Column Dispersion

Maximum Sample Volume and Maximum Extra-Column Dispersion 

In a packed column the HETP depends on the particle diameter and is not related to the column radius. As a result, an expression for the optimum particle diameter is independently derived, and then the column radius determined from the extracolumn dispersion. This is not true for the open tubular column, as the HETP is determined by the column radius. It follows that a converse procedure must be employed. Firstly the optimum column radius is determined and then the maximum extra-column dispersion that the column can tolerate calculated. Thus, with open tubular columns, the chromatographic system, in particular the detector dispersion and the maximum sample volume, is dictated by the column design which, in turn, is governed by the nature of the separation. 

As already stated, the maximum extra-column dispersion that can be tolerated, such that the resolution is not significantly reduced, will be equivalent to an increase of 10% of the column variance. 

If the total extra-column dispersion is shared equally between the sample volume and the detector, 

Marcel Dekker, Inc. 270 Madison Avenue, New York, New York 10016 

---

Having established that a finite volume of sample causes peak dispersion and that it is highly desirable to limit that dispersion to a level that does not impair the performance of the column, the maximum sample volume that can be tolerated can be evaluated by employing the principle of the summation of variances. Let a volume (Vi) be injected onto a column. This sample volume (Vi) will be dispersed on the front of the column in the form of a rectangular distribution. The eluted peak will have an overall variance that consists of that produced by the column and other parts of the mobile phase conduit system plus that due to the dispersion from the finite sample volume. For convenience, the dispersion contributed by parts of the mobile phase system, other than the column (except for that from the finite sample volume), will be considered negligible. In most well-designed chromatographic systems, this will be true, particularly for well-packed GC and LC columns. However, for open tubular columns in GC, and possibly microbore columns in LC, where peak volumes can be extremely small, this may not necessarily be true, and other extra-column dispersion sources may need to be taken into account. It is now possible to apply the principle of the summation of variances to the effect of sample volume. 

Extra-column dispersion can arise in the sample valve, unions, frits, connecting tubing, and the sensor cell of the detector. The maximum sample volume, i.e., that volume that contributes less than 10% to the column variance, is determined by the type of column, dimensions of the column and the chromatographic characteristics of the solute. In practice, the majority of the permitted extra-column dispersion should... 

Unfortunately, the magnitude of the variance contribution from each source will be different and the ultimate minimum size of each is often dictated by the limitations in the physical construction of of the different parts of the apparatus and consequently not controllable. It follows that equipartition of the permitted extra column dispersion is not possible. It will be seen later that the the maximum sample volume provides the maximum chromatographic mass and concentration sensitivity. Consequently, all other sources of dispersion must be kept to the absolute minimum to allow as large a sample volume as possible to be placed on the column without exceeding the permitted limit. At the same time it must be stressed, that all the permitted extra column dispersion can not be allotted solely to the sample volume. 

The properties of open tubular columns shown in figures (I) to (6) indicate that the areas where such columns would have practical use is very restricted. At pressures in excess of 10 ps.i., and whatever the nature of the separation, whether simple or difficult, the optimum column diameters are so small that they would be exceedingly difficult to fabricate or coat with stationary phase. The maximum sample volumes and extra column dispersion that couid be tolerated would also be well below that physically possible at this time. At relatively low pressures, that Is at pressures less than 10 p.s.l. the diameter of the optimum column is large enough to fabricate and coat with stationary phase providing the separations required are difficult i.c. the separation ratio of the critical pair must be less than 1.03. However, even under these conditions the sample volume will be extremely small, the extra column dispersion restricted to an almost impossibly low limit and the analysis time would be very long Nevertheless, open tubular columns used for very difficult separations... 

It follows that the maximum permissible time constant will be only 10% of the peak standard deviation if sufficient extra column dispersion is retained for sample volume and detector cell volume... 

---