Rhodium demonstrating formation

They observed the complete deactivation of the rhodium catalyst whether immobilized or not in the presence of free amines. When no amine was present, styrene formation was not observed. After 17 h of a reaction in which both catalysts were immobilized, the yield of the product, ethylbenzene, was 52%, again demonstrating the principle of enabling two otherwise incompatible catalysts to work concomitantly in order to achieve process intensification. 

Considerable work has been conducted on a water-soluble catalyst using sulfonated phosphine-modified rhodium. Details of this chemistry will be described in Chapter 5. The general concept (Figure 2.3) is to make the catalyst water soluble, then after product formation, decant the product. In order for the water-soluble catalyst to be effective, the alkene must dissolve in the aqueous layer. This has been demonstrated on a commercial basis using propene. The low solubility of higher alkenes in the aqueous catalyst layer has proven problematic. The desirable characteristic of the ligand, water solubility, is needed in the separation step but is a disadvantage in the reaction step. 

Efforts to tune the reactivity of rhodium catalysts by altering structure, solvent, and other factors have been pursued.49,493 50 Although there is (justifiably) much attention given to catalysts which provide /raor-addition processes, it is probably underappreciated that appropriate rhodium complexes, especially cationic phosphine complexes, can be very good and reliable catalysts for the formation of ( )-/3-silane products from a air-addition process. The possibilities and range of substrate tolerance are demonstrated by the two examples in Scheme 9. A very bulky tertiary propargylic alcohol as well as a simple linear alkyne provide excellent access to the CE)-/3-vinylsilane products.4 a 1 In order to achieve clean air-addition, cationic complexes have provided consistent results, since vinylmetal isomerization becomes less competitive for a cationic intermediate. Thus, halide-free systems with... 

TPP)Rh(L)J+C1 in the presence of an alkyl halide leads to a given (P)Rh(R) or (P)Rh(RX) complex. The yield was nearly quantitative (>80X) in most cases based on the rhodium porphyrin starting species. However, it should be noted that excess alkyl halide was used in Equation 3 in order to suppress the competing dimerization reaction shown in Equation 1. The ultimate (P)Rh(R) products generated by electrosynthesis were also characterized by H l MR, which demonstrated the formation of only one porphyrin product(lA). No reaction is observed between (P)Rh and aryl halides but this is expected from chemical reactivity studles(10,15). Table I also presents electronic absorption spectra and the reduction and oxidation potentials of the electrogenerated (P)Rh(R) complexes. 

In summary, the four chemical systems described in this paper demonstrate the versatility and selectivity of electrochemical methods for synthesis and characterization of metal-carbon a-bonded metalloporphyrins. The described rhodium and cobalt systems demonstrate significant differences with respect to their formation, stability and to some extend, reactivity of the low valent species. On the other hand, properties of the electroche-mically generated mono-alkyl or mono-aryl germanium and silicon systems are similar to each other. 

The stereospecific rhodium-catalyzed allyhc hnchpin cross-couphng reaction provides an expeditious route to stereotetrads (Scheme 10.5). This study demonstrated that improved stereospecificity could be obtained at lower temperature for the formation of the alkylation product 18 (2° 1°=24 1 ds=26 l compare Tab. 10.2, entry 1). Krapcho... 

The perfluoroacetamide catalysts, rhodium(II) trifluoroacetamidate [Rh2(tfm)4] and rhodium(II) perfluorobutyramidate [Rh2(pfbm)4], are interesting hybrid molecules that combine the features of the amidate and perfluorinated ligands. In early studies, these catalysts were shown to prefer insertion over cycloaddition [30]. They also demonstrated a preference for oxindole formation via aromatic C-H insertion [31], even over other potential reactions [86]. In still another example, rhodium(II) perfluorobutyramidate showed a preference for aromatic C-H insertion over pyridinium ylide formation, in the synthesis of an indole nucleus [32]. Despite this demonstrated propensity for aromatic insertion, the perfluorobutyramidate was shown to be an efficient catalyst for the generation of isomtinchnones [33]. The chemoselectivity of this catalyst was further demonstrated in the cycloaddition with ethyl vinyl ethers [87] and its application to diversity-oriented synthesis [88]. However, it was demonstrated that while diazo imides do form isomtinchnones under these conditions, the selectivity was completely reversed from that observed with rhodium(II) acetate [89, 90]. 

Wenkert and Khatuya (51) examined the competition between direct insertion of a carbene into furan (via cyclopropanation) and ylide formation with reactive side-chain functionality such as esters, aldehydes, and acetals. They demonstrated the ease of formation of aldehyde derived carbonyl ylides (Scheme 4.30) as opposed to reaction with the electron-rich olefin of the furan. Treatment of 3-furfural (136) with ethyl diazoacetate (EDA) and rhodium acetate led to formation of ylide 137, followed by trapping with a second molecule of furfural to give the acetal 138 as an equal mixture of isomers at the acetal hydrogen position. 

In recent work67, it has been demonstrated that simple a-diazo ketones and esters can, in fact, be induced to undergo 1,5-insertion in preparatively useful yields. It was already known51 that in the rhodium-catalyzed insertion process, methyl C-H is electronically less reactive than methylene C-H or methine C-H. It therefore seemed likely that competing -hydride elimination would be least likely with a diazoethyl ketone. Indeed, on cyclization of 2-diazo-3-tetrade-canone, only a trace of the enone product from /J-hydride elimination is observed. The predominant side reaction competing with 1,5-insertion is dimer formation. 

Carbonyl ylides possess versatile reactivities, among which the 1,3-dipolar cycloaddition is the most common and important reaction. The reaction sequence of ylide formation and then 1,3-dipolar cycloaddition can occur in either inter- or intramolecular manner. When the reaction occurs intermolecularly, the overall reaction is a one-pot three-eomponent process leading to oxygen-containing five-membered cyclic compounds, as demonstrated by the example shown in Scheme 8. A mixture of diazo ester 64, benzaldehyde, and dimethyl maleate, upon heating to reflux in CH2CI2 in the presence of 1 mol% rhodium(ii) perfluorobutyrate [Rh2(pfb)4], yields tetrahedrofuran derivative 65 in 49% yield as single diastereomer. " ... 

---