Return process

Excessive mixing Limit agitator power input and provide proper of reactants or impeller design impurities which, Return process to pilot or development to rede-promotes process to eliminate or minimize this emulsification. problem Poor phase separa- tion resulting in L it shaft speed problems in subse- Monitor shaft speed quent processing, phase separation steps or in down- stream equipment. I" " de-emulsifiers CCPS G-29 Lees 1996... 

Return processes associated with returning or receiving products returned for some reason. 

At times it can be useful to carry out a sort of reversal electrolysis, i.e. reoxidize the reduced species (or reduce that oxidized) immediately after generating it to re-obtain the initial species. As shown in Table 3, the comparison between the amount of electricity (in C) consumed in the forward process, Qf, and that consumed in the return process, Qr, can be useful in the identification of the electrode mechanism involved in the process under study (even if in general it is less simple than appears). 

No. It should be the same. If different, the system will return to the initial state A with a net gain of internal energy. In other words, if different, the system will gain even more energy by repeating the process from nowhere. This is contrary to the First Law of Thermodynamics. Therefore the internal energy gained in the forward process must be equal to that lost in the return process. 

The remarkable agreement in the above results surprised Bunton and Del Pesco (1969) because, as they pointed out, no allowance was made for the temperatures of the two processes, and for the presence of solvent and ion-pair return processes. From extensive studies of structurally related methyl norbornyl chlorides (e.g. 19), they concluded... 

An ambident anion is one with different kinds of atoms which may become attached to a carbocation. Isomerization of the anionic portion permits detection of ion pair return in close analogy to the equilibration of 180 labeled benzoate or sulfonate esters. The isomerization of thiocyanates (112) to isothiocyanates (113) is the most studied of these ambident rearrangements 5, "6 In some respects these reactions differ from the return processes of carboxylate or sulfonate ion pairs ... 

These deformations can be reversed, that is, if temperatures are decreased, there is a return process. The effect of temperature depends on its value and the duration... 

In Chapter 27, King et al. present their work on determining reaction mechanisms for reaction of nucleophiles with sulfonyl chlorides. Many of the same phenomena observed for the more familiar nucleophilic attack at carbon are seen. Evidence is presented for pentavalent intermediates, direct displacement, elimination-addition (through sulfenes, C = S02), neighboring-group participation (through a (3-sultone), and return processes. 

Pressure effects on the rate of these thermal return processes were investigated in ethanol and MPD [46]. The results for DOCl are shown in Fig. 3.18. 

The same frequency would be emitted in the return process... 

Diagram a shows the work done by the system in going from A B and then from B C b shows the work done on the system in the return process, via D, The net work, obtained by subtracting the shaded area in b from that in a. is thus the area enclosed by the cycle c. 

SecOTidly, retailers engaged in the distribution network can serve as collection points for the reverse logistics and facilitate the return process from customers. Lasdy, to ensure timely returns of used cores, it is important to create mechanisms to encourage customers to return used cores. Thus, deposits at the time of purchase time, discotuits in new products, coupons, leasing alternatives, and service contracts are some examples of common strategies (Ostlin et al. 2009). 

Level 1 Provides a broad definition of the plan, source, make, delivery, and return process t5q>es, and is the point at whieh a eompany establishes its supply ehain eom-petitive objectives. 

Design source, make, deliver, and return processes + + + + +... 

Council of Supply Chain Management Professionals, Supply Chain Management Process Standards, Council of Supply Chain Management Professionals, 2004. The standards are in six volumes Plan Processes, Source Processes, Make Processes, Deliver Processes, Return Processes, Enable Processes. 

RETURN processes SCOR processes addressing return and receipt of products for repair, overhaul, or refurbishment, or for resale. Includes postdelivery customer support. 

Now the defining equation (1 13) for an entropy change is only applicable imder reversible conditions. We shall therefore suppose that, after the original process A->B has taken place within the adiabatic enclosure, the reverse change of state B- A is carried out under conditions which are known to be reversible. In the general case, as we have noted previously, this return process cannot be carried out adiabatically. Let it be devised in such a way that any heat, which must be absorbed by the system is taken in from a single heat bath at a temperature T (Fig. 8). 

Moreover, sourcing processes are also carried out at the laptop distributors as well as at the desktop retailers place. Here, laptops and desktops are sourced for further distribution. Regarding the distribution processes, they are carried out at various places in this example. However, the desktop distribution center and the laptop distributor represent the assembly point for the worldwide distribution of the products. The plan process associated with the planning activities required to operate the supply chain are conducted at the headquarter. The source returns as well as the deliver return processes are not carried out in this specific example. 

Table 9.5 Configuration of supply chain source process and the source return process...

A return process is performed for the sourced good or product... 

---