Reference design

Under the null hypothesis, it is assumed that the sample came from a population whose mean [L is equivalent to some base or reference designated by lo. This can take one of three forms ... 

The standard requires that the design and development plans describe or reference design and development activities. Hence where you need to produce separate plans they should be referenced in the overall plan so that you remain in control of all the activities. 

Reference Design Patients (Age) Drug (Dose) Results Comments Adverse Effects Comments... 

The middle section of the code defines the circuit itself. The structure of each component is roughly similar. The first variable is the reference designator. The next variable is the number of nodes that the component... 

In this line, resistor R1 is defined as a resistor connected from node 1 to node 2 with a value of 100 2. Several rules apply in defining components. Node 0 is reserved for ground. All circuits must have at least one ground connection. Also, reference designators are limited to alphanumeric characters (Fig. 2.2). Longer statements may be continued on the following line by using a + symbol as the first character to indicate a continuation from the previous line. 

Technical-economic parameters of the MHR-T energy-technological complex recommended as reference design parameters are as displayed in Table 1 (Kostin, 2006 Mitenkov, 2004). 

In addition to the shaft power needed to raise the water heat transfer medium from the low to high loop pressure, additional compressor power is needed to overcome frictional pressure drop around the loop. The power associated with this loss has been compared with that of the high temperature process loop in the reference design. To understand the role of the different heat transport fluid -water in the alternate design versus helium in the reference design - the pumping power is expressed as a fraction of the pumping power per unit thermal power transported. This permits a consistent comparison between the two loops even if they differ in total thermal power transported. 

Performance measure Assessment with respect to reference design... 

When two dyes are used, there are two experimental approaches (Figure 3.2). In the most common approach ( reference design, Figure 3.2), the experimental sample is labeled with one dye while the common reference sample is labeled with the second dye, and both are hybridized to the same microarray. Alternatively, for a more statistically balanced and efficient experiment, samples can be hybridized with other samples in a loop design (Figure 3.2). In the loop design, the two experimental samples (no common reference) are labeled with the two different dyes and hybridized to the microarray. 

Figure 3.2. Reference versus loop design for two-dye microarrays. Two samples labeled with different fluorescent dyes are hybridized to a microarray with hundreds to thousands of different genes printed as spots. Arrows represent the microarrays and the hybridization scheme the sample at the base of the arrow is labeled with one dye, and the sample at the head of the arrow is labeled with a different dye. In a reference design, each sample is hybridized with the same reference sample. This reference might be a pool of different RNA samples or a control RNA sample. Each sample is measured once while the reference is measured n times, where n is the number of samples. In a loop design, samples are hybridized with other samples. Thus, each sample is measured twice in a balanced design (once with each dye).

URS Reference Functional Specification Reference Design Specification Reference DQ Reference Source Code Review Reference... 

A textbook and standard reference designed to provide a thorough introduction to toxicology in the broadest sense. Strengths include coverage of methods, techniques, procedures, interpretation of data, and examination of controversial areas. 

Reference Design Delivery Dose (pg/kg) Size (n) Primary Endpoints Results... 

In the past, engineers used steam tables to obtain properties of water and steam. While such books still exist [6, 7], it is now usually more convenient to use software that implements lAPWS property standards [8]. Table 1.1 reports the thermodynamic properties of water for saturated liquid and vapor. Such short tables are useful for quick reference design calculations usually require more extensive tables or software. 

Note that the reference designators of the components have changed in this section for convenience. What we are now calling Rl was Rf2 when we previously discussed the voltage divider. Similarly, the gray unnamed resistor in Figure 7-15 was previously called Rfl. ... 

The thermal-neutron balance equation for the reference design condition states that the rate of production of thermal neutrons equals the rate of consumption ... 

---