Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Water heat transfer

Figure 2-28. Coefficient of heat transfer, water inside tubes (Nfie>2100). Figure 2-28. Coefficient of heat transfer, water inside tubes (Nfie>2100).
Figure 7.25 Mobile recirculating electrolyte system in AFCs. Heat transfer, water removal, and impurity removal occur through the flushed electrol5he. (Reproduced with permission from Ref. [58].)... Figure 7.25 Mobile recirculating electrolyte system in AFCs. Heat transfer, water removal, and impurity removal occur through the flushed electrol5he. (Reproduced with permission from Ref. [58].)...
Most refrigeration systems are essentially the same as the heat pump cycle shown in Fig. 6.37. Heat is absorbed at low temperature, servicing the process, and rejected at higher temperature either directly to ambient (cooling water or air cooling) or to heat recovery in the process. Heat transfer takes place essentially over latent heat profiles. Such cycles can be much more complex if more than one refrigeration level is involved. [Pg.206]

Use water or other nonflammable heat transfer medium. [Pg.271]

The thermal profile through the reactor will in most circumstances be carefully optimized to maximize selectivity, extend catalyst life, etc. Because of this, direct heat integration with other process streams is almost never carried out. The heat transfer to or from the reactor is instead usually carried out by a heat transfer intermediate. For example, in exothermic reactions, cooling might occur by boiling water to raise steam, which, in turn, can be used to heat cold streams elsewhere in the process. [Pg.327]

If indirect heat transfer is used with a large temperature difference to promote high rates of cooling, then the cooling fluid (e.g., boiling water) is fixed by process requirements. In this case, the heat of reaction is not available at the temperature of the reactor effluent. Rather, the heat of reaction becomes available at the temperature of the quench fluid. Thus the feed stream to the reactor is a cold stream, the quench fluid is a hot stream, and the reactor effluent after the quench is also a hot stream. [Pg.329]

The reactor effluent might require cooling by direct heat transfer because the reaction needs to be stopped quickly, or a conventional exchanger would foul, or the reactor products are too hot or corrosive to pass to a conventional heat exchanger. The reactor product is mixed with a liquid that can be recycled, cooled product, or an inert material such as water. The liquid vaporizes partially or totally and cools the reactor effluent. Here, the reactor Teed is a cold stream, and the vapor and any liquid from the quench are hot streams. [Pg.329]

The reaction is exothermic, and multitubular reactors are employed with indirect cooling of the reactor via a heat transfer medium. A number of heat transfer media have been proposed to carry out the reactor cooling, such as hot oil circuits, water, sulfur, mercury, etc. However, the favored heat transfer medium is usually a molten heat transfer salt which is a eutectic mixture of sodium-potassium nitrate-nitrite. [Pg.332]

Following the pinch rules, there should be no heat transfer across either the process pinch or the utility pinch by process-to-process heat exchange. Also, there must be no use of inappropriate utilities. This means that above the utility pinch in Fig. 16.17a, high-pressure steam should be used and no low-pressure steam or cooling water. Between the utility pinch and the process pinch, low-pressure steam should be used and no high-pressure steam or cooling water. Below the process pinch in Fig. 16.17, only cooling water should be used. The appropriate utility streams have been included with the process streams in Fig. 16.17a. [Pg.381]

Emulsion polymerization also has the advantages of good heat transfer and low viscosity, which follow from the presence of the aqueous phase. The resulting aqueous dispersion of polymer is called a latex. The polymer can be subsequently separated from the aqueous portion of the latex or the latter can be used directly in eventual appUcations. For example, in coatings applications-such as paints, paper coatings, floor pohshes-soft polymer particles coalesce into a continuous film with the evaporation of water after the latex has been applied to the substrate. [Pg.403]


See other pages where Water heat transfer is mentioned: [Pg.15]    [Pg.24]    [Pg.15]    [Pg.89]    [Pg.152]    [Pg.940]    [Pg.15]    [Pg.24]    [Pg.15]    [Pg.89]    [Pg.152]    [Pg.940]    [Pg.220]    [Pg.264]    [Pg.241]    [Pg.324]    [Pg.662]    [Pg.176]    [Pg.215]    [Pg.305]    [Pg.21]    [Pg.48]    [Pg.64]    [Pg.70]    [Pg.113]    [Pg.129]    [Pg.163]    [Pg.247]    [Pg.331]    [Pg.332]    [Pg.332]    [Pg.373]    [Pg.380]    [Pg.408]    [Pg.447]    [Pg.465]    [Pg.467]    [Pg.490]    [Pg.571]    [Pg.613]    [Pg.680]    [Pg.699]    [Pg.742]    [Pg.801]    [Pg.815]    [Pg.818]   
See also in sourсe #XX -- [ Pg.596 ]




SEARCH



Changes during heating water as the heat transfer

HEAT-TRANSFER MEDIA OTHER THAN WATER

Heat Transfer Deterioration in Supercritical Water

Heat transfer coefficients water in tubes

Heat transfer media Water, cooling

Heat transfer systems, water handling

Heat transfer water clusters

Heat transfer water cooling theory

Heat water

Simplified Relations for Boiling Heat Transfer with Water

Water heat transfer coefficient

Water heating

Water transfer

© 2024 chempedia.info