Reduction isotopes

Boron exists naturally as 19.78% lOB isotope and 80.22% IIB isotope. High-purity crystalline boron may be prepared by the vapor phase reduction of boron trichloride or tribromide with hydrogen on electrically heated filaments. The impure or amorphous, boron, a brownish-black powder, can be obtained by heating the trioxide with magnesium powder. 

Separation of tantalum from niobium requires several complicated steps. Several methods are used to commercially produce the element, including electrolysis of molten potassium fluorotantalate, reduction of potassium fluorotantalate with sodium, or reacting tantalum carbide with tantalum oxide. Twenty five isotopes of tantalum are known to exist. Natural tantalum contains two isotopes. 

Gr. aktis, aktinos, beam or ray). Discovered by Andre Debierne in 1899 and independently by F. Giesel in 1902. Occurs naturally in association with uranium minerals. Actinium-227, a decay product of uranium-235, is a beta emitter with a 21.6-year half-life. Its principal decay products are thorium-227 (18.5-day half-life), radium-223 (11.4-day half-life), and a number of short-lived products including radon, bismuth, polonium, and lead isotopes. In equilibrium with its decay products, it is a powerful source of alpha rays. Actinium metal has been prepared by the reduction of actinium fluoride with lithium vapor at about 1100 to 1300-degrees G. The chemical behavior of actinium is similar to that of the rare earths, particularly lanthanum. Purified actinium comes into equilibrium with its decay products at the end of 185 days, and then decays according to its 21.6-year half-life. It is about 150 times as active as radium, making it of value in the production of neutrons. 

By-Products. The PUREX process is efficient at separating uranium and plutonium from everything else in the spent fuel. Within the high level waste stream are a number of components which have, from time to time, been sufficiendy interesting to warrant their recovery. The decision to recover a particular isotope is usually based on a combination of market incentives and desired waste reduction. 

A unique problem arises when reducing the fissile isotope The amount of that can be reduced is limited by its critical mass. In these cases, where the charge must be kept relatively small, calcium becomes the preferred reductant, and iodine is often used as a reaction booster. This method was introduced by Baker in 1946 (54). Researchers at Los Alamos National Laboratory have recently introduced a laser-initiated modification to this reduction process that offers several advantages (55). A carbon dioxide laser is used to initiate the reaction between UF and calcium metal. This new method does not requite induction heating in a closed bomb, nor does it utilize iodine as a booster. This promising technology has been demonstrated on a 200 g scale. 

Properties of T2O. Some important physical properties of T2O are Hsted in Table 2. Tritium oxide [14940-65-9] can be prepared by catalytic oxidation of T2 or by reduction of copper oxide using tritium gas. T2O, even of low (2—19% T) isotopic abundance, undergoes radiation decomposition to form HT and O2. Decomposition continues, even at 77 K, when the water is fro2en. Pure tritiated water irradiates itself at the rate of 10 MGy/d (10 rad/d). A stationary concentration of tritium peroxide, T2O2, is always present (9). AH of these factors must be taken into account in evaluating the physical constants of a particular sample of T2O. 

For a given hydrogen donor S—H, replacement by S—D leads to a decreased rate of reduction, relative to nonproductive decay to the ground state." This decreased rate is consistent with a primary isotope effect in the hydrogen abstraction step,... 

The isotopic purity of the products from a lithium aluminum deuteride reduction is usually equivalent to that of the reagent. The presence of moisture has little effect on the isotope composition of the products, causing only the decomposition of some of the reagent. For the best results, however, it is advisable to distill the solvent— usually ether, tetrahydrofuran or dioxane depending on the desired reaction temperature—from lithium aluminum hydride directly into the reaction flask. In this manner the reduction of 3-keto-5a-steroids (60), for example, gives the corresponding 3a-di alcohols (61) in 98% isotopic purity. ... 

With certain carbonyl compounds, however, such as 3-keto steroids, the isotopic composition is poor due to the rapid exchange of the activated a-hydrogens in the substrate prior to reduction. The corresponding alcohols, in their thermodynamically more stable configuration, are usually found as... 

This reaction is especially well suited for the reduction of tertiary aldehydes which have no activated a-hydrogens. In this case only two deuteriums are incorporated in place of the carbonyl oxygen. The reduction of 12-methoxypodocarpa-8,ll,13-trien-17-al (82) provides an illustrative example. After back exchange of the aromatic deuteriums, the isotopic purity of the resulting dideuterio reduction product (83) is 92%. ... 

Two techniques, electrochemical reduction (section IIl-C) and Clem-mensen reduction (section ITI-D), have previously been recommended for the direct reduction of isolated ketones to hydrocarbons. Since the applicability of these methods is limited to compounds which can withstand strongly acidic reaction conditions or to cases where isotope scrambling is not a problem, it is desirable to provide milder alternative procedures. Two of the methods discussed in this section, desulfurization of mercaptal derivatives with deuterated Raney nickel (section IV-A) and metal deuteride reduction of tosylhydrazone derivatives (section IV-B), permit the replacement of a carbonyl oxygen by deuterium under neutral or alkaline conditions. 

This reaction sequence proceeds by cis addition of deuterium and the reduction products usually exhibit high isotopic purity. For example, 5a-cholest-2-ene (136), which is known to give a product of very unsatisfactory isotopic purity when deuterated with heterogeneous catalysts (see section V-A), gives 2<, 3 -d2-5a-cholestane (137) with better than 95% isotopic purity in homogeneous solution. ... 

A pertinent example is the reduction of 5a-androst-8-en-l 1-one (154) which yields 8 -di-5a-androstan-l 1-one (155) in 93% isotopic purity. Saturation of A -6-keto steroids gives equally good results for labeling the 8/5-position. ... 

A recent modification of this technique utilizes A,A-d2-propylamine as the solvent for the lithium reduction, thereby eliminating the inconveniences associated with the preparation and handling of liquid deuterioammonia. Under these conditions the reaction can be carried out at room temperature and less overreduction of the carbonyl group is observed. For example, the reduction of A" -3-keto steroids (159) under these conditions, followed by back exchange in protic media, leads to the corresponding 5a-di-3-ketones (160) which exhibit good isotopic purity. ... 

Some advantages of this reaction are high yield if the tosylate is in a sterically accessible position excellent isotopic purity of the product (usually higher than-95%) and perhaps most important, access to stereospecifically labeled methylene derivatives. For example, deuteride displacement of 3j -tosylates (183) yields the corresponding Sa-d derivative (185) in 96-98% isotopic purity. Application of this method to the labeled sulfonate (184), obtained. by lithium aluminum deuteride reduction of a 3-ketone precursor (see section HI-A) followed by tosylation, provides an excellent synthesis of 3,3-d2 labeled steroids (186) without isotopic scrambling at the adjacent positions. The only other method which provides products of comparable isotopic purity at this position is the reduction of the tosyl-hydrazone derivative of 3-keto steroids (section IV-B). 

---