Recycle acrylonitrile-butadiene-styrene

Mahanta and co-workers [71] prepared a blend of rPC, recycled acrylonitrile-butadiene-styrene (rABS) and nanoclay, Cloisite SOB or Cloisite 15A. The blend was compatibilised with both PP-g-MA and solid epoxy resin. The mechanical properties of the rABS/rPC blend without a compatibiliser decreased in comparison to neat matrices. However, upon the addition of 5 wt% of a PP-g-MA compatibiliser, the mechanical properties improved. Similarly, further addition of the epoxy led to a synergistic behaviour in mechanical performance, particularly the modulus and tensile strength. Also, a greater improvement of the modulus was achieved in the rPC-rich blend by simultaneously adding two nanoclays. The thermal stability of the blends compatibilised with PP-g-MA and epoxy exhibited positive thermal properties. 

A. Arostegui, M. Sarrionandia, J. Aurrekoetxea, and I. Urrutibeas-coa, Effect of dissolution-based recycling on the degradation and the mechanical properties of acrylonitrile-butadiene-styrene copolymer, Polym. Degrad. Stab., 91(ll) 2768-2774, November 2006. 

The major challenge to all recovery systems will be the increasing level of other plastic types in the feed material. Materials such as ABS (acrylonitrile butadiene styrene) are being used in VRLA battery cases, due to their toughness and rigidity relative to traditional polypropylene. For the recycler, this means that the valuable polypropylene tonnage will fall with a reciprocal increase in plastic types that cannot be recycled. This material will have to be disposed of, as ABS and... 

Acrylonitrile/Butadiene/Styrene (ABS) Acry-lonitrile/butadiene/styrene (ABS) polymers are not true terpolymers. As HIPS they are multipolymer composite materials, also called polyblends. Continuous ABS is made by the copolymerization of styrene and acrylonitrile (SAN) in the presence of dissolved PB rubber. It is common to make further physical blends of ABS with different amounts of SAN copolymers to tailor product properties. Similar to the bulk continuous HIPS process, in the ABS process, high di-PB (>50%, >85% 1,4-addition) is dissolved in styrene monomer, or in the process solvent, and fed continuously to a CSTR where streams of AN monomer, recycled S/AN blends from the evaporator and separation stages, peroxide or azo initiators, antioxidants and additives are continuously metered according to the required mass balance to keep the copolymer composition constant over time at steady state. 

RECYCLING OF ACRYLONITRILE/ BUTADIENE/STYRENE COPOLYMERS (ABS) AND OTHER PLASTICS... 

Acrylonitrile-butadiene-styrene (ABS) is one of the most frequently used polymers in the production of electrical and electronic equipment, it also has widespread applications in automobiles, communication instruments and other commodities. Within the electrical and electronic sector, the quantity of recycled plastics could be increased via the recycling of ABS to reduce environmental, economic and energy issues. Table 2.5 illustrates some of the physical parameters of ABS. 

Currently, most WPC are made with PE, both recycled and virgin, for use in exterior building components. However, WPC made with wood-PP are typically used in automotive applications and consumer products, and these composites have recently been investigated for use in building profiles. Wood-PVC composites typically used in window manufacture are now being used in decking as well. Polystyrene and acrylonitrile-butadiene-styrene (ABS) are also being nsed. 

A recent paper by Meyer et indicates that it is the flame retardants that determine the recyclability of a polymer. Engineering plastics such as acrylonitrile-butadiene-styrene which contain PBDE are unsuitable for recycling because of the generation of PBDF and PBDD s. Moldings containing... 

Antimony has been detected in electronic waste (e-waste) from different uses. This includes use in semi-conductor components as a flame retardant, or as a synergist with other flame retardants in circuit boards (Bi et al. 2011 Lincoln et al. 2007), and in plastic housings of electronic equipment (Santos et al. 2010). Antimony trioxide is used as a flame retardant in hard polymer plastics including acrylonitrile-butadiene-styrene plastic (ABS) commonly used for TV and computer housings (Tostar et al. 2013). Waste electric and electronic equipment (WEEE) exposure to antimony is of concern in Asia where most of the global WEEE is recycled, land-fiUed, or incinerated (Santos et al. 2010). 

Acrylic resin Acrylonitrilefbutadiene/styrene copolymer Bis (2,4-di-t-butylphenyl) pentaerythritol diphosphite Butadiene/acrylonitrile copolymer EthyleneA/A copolymer Methoxyethyl acrylate Methyl methacrylate butadiene styrene terpolymer Polyethylene elastomer, chlorinated 2-Propenoic acid, 2-methylmethyl ester, polymer with 1,3-butadiene and butyl 2-propenoate impact modifier, PVC rigid EVA/PVC graft polymer impact modifier, recycled polyamides EPDM, maleated impact modifier, thermoplastics Butadiene/acrylonitrile copolymer impact strength modifier PEG-6 trimethylolpropane impact-resistance lights Polyester carbonate resin impact-resistance, lights Polyester carbonate resin impeller... 

---