Reactor multiple reactions

P3-9. This problem begins to prepare the students for those situations (e membrane reactorS/ multiple reactions) where they cannot use conversU as a variable. 

I datch reactor multiple reaction and multiple species t requires the odes be in functiun rxnede ... 

Energy balance— whole reactor— multiple reactions... 

Multiple reactions also can occur with impurities that enter with the feed and undergo reaction. Again, such reactions should be minimized, but the most efiective means of dealing with byproduct reactions caused by feed impurities is not to alter reactor conditions but to introduce feed purification. 

Multiple reactions in parallel producing byproducts. Consider again the system of parallel reactions from Eqs. (2.16) and (2.17). A batch or plug-flow reactor maintains higher average concentrations of feed (Cfeed) than a continuous well-mixed reactor, in which the incoming feed is instantly diluted by the PRODUCT and... 

Figure 2.2 summarizes these arguments to choose a reactor for systems of multiple reactions in parallel. 

In the preceding section, the choice of reactor type was made on the basis of which gave the most appropriate concentration profile as the reaction progressed in order to minimize volume for single reactions or maximize selectivity for multiple reactions for a given conversion. However, after making the decision to choose one type of reactor or another, there are still important concentration effects to be considered. 

Multiple reactions in parallel producing byproducts. Once the reactor type is chosen to maximize selectivity, we are in a position to alter selectivity further in parallel reaction systems. Consider the parallel reaction system from Eq. (2.20). To maximize selectivity for this system, we minimize the ratio given by Eq. (2.21) ... 

The choice of reactor temperature depends on many factors. Generally, the higher the rate of reaction, the smaller the reactor volume. Practical upper limits are set by safety considerations, materials-of-construction limitations, or maximum operating temperature for the catalyst. Whether the reaction system involves single or multiple reactions, and whether the reactions are reversible, also affects the choice of reactor temperature, as we shall now discuss. 

The selection of reactor pressure for vapor-phase reversible reactions depends on whether there is a decrease or increase in the number of moles and whether there is a system of single or multiple reactions. 

Multiple reactions producing byproducts. The arguments presented for the effect of pressure on single vapor-phase reactions can be used for the primary reaction when dealing with multiple reactions. Again, selectivity is likely to be more important than reactor volume for a given conversion. 

Because the characteristic of tubular reactors approximates plug-flow, they are used if careful control of residence time is important, as in the case where there are multiple reactions in series. High surface area to volume ratios are possible, which is an advantage if high rates of heat transfer are required. It is sometimes possible to approach isothermal conditions or a predetermined temperature profile by careful design of the heat transfer arrangements. 

Figure 2.10 Choosing the reactor to maximize selectivity for multiple reactions producing byproducts.

Multiple reactions. For multiple reactions in which the byproduct is formed in parallel, the selectivity may increase or decrease as conversion increases. If the byproduct reaction is a higher order than the primary reaction, selectivity increases for increasing reactor conversion. In this case, the same initial setting as single reactions should be used. If the byproduct reaction of the parallel system is a... 

It should be emphasized that these recommendations for the initial settings of the reactor conversion will almost certainly change at a later stage, since reactor conversion is an extremely important optimization variable. When dealing with multiple reactions, selectivity is maximized for the chosen conversion. Thus a reactor type, temperature, pressure, and catalyst are chosen to this end. Figure 2.10 summarizes the basic decisions which must be made to maximize selectivity. ... 

Reactor conversion. In Chap. 2 an initial choice was made of reactor type, operating conditions, and conversion. Only in extreme cases would the reactor be operated close to complete conversion. The initial setting for the conversion varies according to whether there are single reactions or multiple reactions producing byproducts and whether reactions are reversible. 

Sampling of a two-fluid phase system containing powdered catalyst can be problematic and should be considered in the reactor design. In the case of complex reacting systems with multiple reaction paths, it is important that isothermal data are obtained. Also, different activation energies for the various reaction paths will make it difficult to evaluate the rate constants from non-isothermal data. 

The component balance for a batch reactor. Equation (1.21), still holds when there are multiple reactions. However, the net rate of formation of the component may be due to several different reactions. Thus,... 

The second use of Equations (2.36) is to eliminate some of the composition variables from rate expressions. For example, 0i-A(a,b) can be converted to i A a) if Equation (2.36) can be applied to each and every point in the reactor. Reactors for which this is possible are said to preserve local stoichiometry. This does not apply to real reactors if there are internal mixing or separation processes, such as molecular diffusion, that distinguish between types of molecules. Neither does it apply to multiple reactions, although this restriction can be relaxed through use of the reaction coordinate method described in the next section. 

---