Reaction time, effect

Aminocyclopropanes were easily acylated by acid chlorides, isocyanates or isothiocyanates (e.g. Refs 3, 24, 27, 36, 71, 80, 82, 125, 178, 179, 184, 224). Polyureas, polyurethanes or polyamides have been prepared from 1,2-diaminocyclopropane Reduction of the carbonyl group in 423 by lithium aluminum hydride worked quite well for tertiary amides 5,473.495. longer reaction times effected a ring-opening in the case of a secondary amide (423, R = H) (LiAlH4 reduction of secondary... 

Wright, G. R. and R. J. Shephard (1978). Brake reaction time—effects of age, sex, and carbon monoxide. Arch. Envir. Health, 33,141—150,... 

Urea is widely used as an airport runway deicer, as it is not corrosive to aircraft materials. However, urea is generally not considered to be a viable alternative deicing chemical for highway applications. Reported limitations include higher application rates, longer reaction times, effectiveness only at temperatures above -10°C, relatively high cost, and significant adverse effects on the environment. ... 

Acetone in conjunction with benzene as a solvent is widely employed. With cyclohexanone as the hydrogen acceptor, coupled with toluene or xylene as solvent, the use of higher reaction temperatures is possible and consequently the reaction time is considerably reduced furthermore, the excess of cyclohexanone can be easily separated from the reaction product by steam distillation. At least 0 25 mol of alkoxide per mol of alcohol is used however, since an excess of alkoxide has no detrimental effect 1 to 3 mols of aluminium alkoxide is recommended, particularly as water, either present in the reagents or formed during secondary reactions, will remove an equivalent quantity of the reagent. In the oxidation of steroids 50-200 mols of acetone or 10-20 mols of cyclohexanone are generally employed. 

This experiment examines the effect of reaction time, temperature, and mole ratio of reactants on the synthetic yield of acetylferrocene by a Eriedel-Crafts acylation of ferrocene. A central composite experimental design is used to find the optimum conditions, but the experiment could be modified to use a factorial design. 

Saturation of the oil with hydrogen is maintained by agitation. The rate of reaction depends on agitation and catalyst concentration. Beyond a certain agitation rate, resistance to mass transfer is eliminated and the rate oecomes independent of pressure. The effect of catalyst concentration also reaches hmiting values. The effects of pressure and temperature on the rate are indicated by Fig. 23-34 and of catalyst concentration by Fig. 23-35. Reaction time is related to temperature, catalyst concentration, and IV in Table 23-13. 

The reaction time can be lengthened considerably without effect. If, however, the time is shortened appreciably, the yield may be markedly lowered. 

Evaluation of the effects of overpressure attributable to the loss of a particular utility supply must include the chain of developments that could occur and the reaction time involved. In situations where fluid flow stops due to failure of its utility supply, but is in parallel with equipment having a different energy source, credit may be taken for the unaffected and functioning equipment to the extent that operation is maintained and the operating equipment will not trip out due to overloading. 

Organic solvents have acute narcotic effects. Aromatic and chlorinated hydrocarbons seem to be especially effective. As stated, the combined effect of several organic solvents is usually considered to be additive. However, there is some evidence that the combined effect may in fact be synergistic. The symptoms caused by organic solvents, often called prenarcotic symptoms, resemble those caused by the use of alcohol. A decrease in reaction time and impairment in various psychological performances can be observed. Acute neurotoxicity can also be detected as abnormalities in the electroencephalogram (EEG i, which records the electrical activity of the brain. " ... 

A remarkable feature of the Birch reduction of estradiol 3-methyl ether derivatives, as well as of other metal-ammonia reductions, is the extreme rapidity of reaction. Sodium and -butyl alcohol, a metal-alcohol combination having a comparatively slow rate of reduction, effects the reduction of estradiol 3-methyl ether to the extent of 96% in 5 minutes at —33° lithium also effects complete reduction under the same conditions as is to be expected. Shorter reaction times were not studied. At —70°, reduction with sodium occurs to the extent of 56 % in 5 minutes, although reduction with lithium is virtually complete (96%) in the same time. (The slow rates of reduction of compounds of the 5-methoxytetralin type is exemplified by 5-methoxy-tetralin itself with sodium and f-butyl alcohol reduction occurs to the extent of only 50% in 6 hours vs. 99+% with lithium.) The iron catalyzed reaction of sodium with alcohols must be very fast since it competes so well with the rapid Birch reduction. One cannot compensate for the presence of iron in a Birch reduction mixture containing sodium by adding additional metal to extend the reaction time. The iron catalyzed sodium-alcohol reaction is sufficiently rapid that the aromatic steroid still remains largely unreduced. 

---