Reach distance

Typically, L may be stream reach distance and u, flow velocity. The diffusion time is approximated by the random walk hypothesis and is approximated by ... 

Wind speed Time before agent reaches Distance between unit and... 

Mital, A., and Faard, H. F. (1990), Effects of Posture, Reach, Distance and Preferred Arm Orientation on Isokinetic Pull Strengths in the Horizontal Plane, Technical Report, Ergonomics and Engineering Controls Laboratory, University of Cincinnati, Cinciimati. 

Eigure 5 Approximate Reach Distances for Average U.S. Male and Female Workers. (From V. Putz-Anderson, Ed., Cumulative Trauma Disorders, copyright 1988 Taylor Francis Books Ltd., by permission)... 

Figure 3 shows the area for males Figure 4 shows the area for females. These are the distances to the end of the thumb with no assistance from movement of the back. Closer is better. Figure 5 shows reach distance above and below the horizontal plane. 

R D projects, see Research and development projects Reach, 1049 Reach distances, 1361 Reactive scheduling, 1733 Ready-made software, 68 Real estate brokers, 1476 Real-life scheduling, theoretical vs., 1732, 1733 Real output, 344... 

Conventional SANS spectrometers make it possible to probe structures over a length scale from near to atomic (10 A) dimensions to a few microns. The ultrasmall-angle neutron-scattering (USANS) instruments that have recently become available have extended the experimental Q range down to 2 x 10- A, reaching distances up to about 30 pm. 

In the case of design the calculations are terminated when the design parameter, usually final moisture content, is reached. Distance at this point is the required dryer length. In the case simulation the calculations are terminated once the dryer length is reached. 

Finally, for projectile range, the analysis of 58 fragments from seven accidents has shown that 70% of the fragments reached distances less than 200 m. However, fragments from... 

Minimize the horizontal reach distance at the origin and the destination of lift or lower. 

Eliminate palm buttons where possible. When necessary, select REES low force 8.5N (1.91b.) palm buttons 04957-012, DaimlerChrysler NPM 22-452-1510 for palm buttons cycle initiation applications. The spacing between the palm buttons should not exceed 61 cm (24"). Static force application to palm buttons should be minimized and must not exceed 4 seconds in duration per cycle. Button boxes should not increase the reach distance from the operator to load the point. Ring guards are required for each horizontal palm button. 

Minimize horizontal reach distances to perform manual task. The maximum horizontal reach distance measured from the edge of any barrier (tool, fixture, vehicle. 

Reach distances are to be minimized and kept with the criteria of section 15.3.3.2 and section 15.3.4.2. 

Locate frequently accessed controls in front of and close to the operator to minimize reach distances. 

Table 26.4. Forced reach distances over barrier rails (from Booth and Thompson )...

Safety distance (reach distance + safety allowance) recommended by DIN 31 001. 

A proposed British Standard provides more usable, and appropriate, data for both reach-through openings and reach-over barriers. Two sets of reach-over data are proposed. The first is based on the existing standard and would only be suitable for low-risk situations where people are unlikely to attempt to reach the danger point. The second is aimed at preventing determined attempts at reaching dangers that have the potential to cause serious injury. The recommended reach distances are comparable with, but rather more cautious than, the data presented in Table 26.4. 

Functional data - the movement of a part of the body in relation to a fixed point, e.g. the reach distance of a seated person. 

Non-adjirstable and adjustable tables, stoves, sirrks, baths, rrrachine tools, desks and benches can be considered from an ergonomic viewpoint. The issues irrvolved have been partly dealt with in relation to chairs. For work performed standing, or with stools, or with sit-stand supports, this will further affect placement and adjustability of other parts of the work station The height, reach distarKe, and hence shape, and angles of tilt can be important, depending on the type of work. Thighs must be able to fit corrrfort-ably under the table, or desk if seated. Reach distance is affected by late pregnancy. 

The related probability that a neutron will suffer a first collision before reaching distance x is called the distribution function for the first collision and is given by... 

The parameter 2 is to be computed from the properties of this ith medium, using the known and the density AT, from Eq. (2.54). Now imagine these various media to be combined to give the resultant mixture. Furthermore, let us assume that collisions with the various nuclear species are independent events, that is, the presence of other nuclear species in no manner affects the interaction between a given nuclear type and a neutron. Then the probability in the mixture that a neutron reach distance x without suffering a collision with a nucleus of type i is given by 1 — F,(x). If a neutron is to survive a distance x without collision in the mixture, it must avoid collision with each nuclear type. Thus, the joint probability is some function 1 — where... 

What The employee and the foremen or supervisor in charge must closely inspect the area to determine whether an electrical power conductor passes through the tree or within reaching distance of an employee who will be working in the tree. 

If you leave a very wet car in the sun, it will get spots similar to those on an improperly washed wineglass. You will need to be parked within reaching distance of a garden hose. And don t forget to close the windows When your car is situated, mix the car wash soap in a bucket as instructed on the wash bottle. Fill another bucket with plain water. 

---