Quick reference charts

Appendix C is a quick reference chart for signs and symptoms of exposure to chemical terrorism agents. The chart is only meant as a guide and is not to be all-inclusive. 

The text also includes quick reference charts and tables to aid the user in on-site measurements (Appendix C) and a glossary of IR/thermography terms (Appendix D). 

Note Due to the condensed nature ol this chart, use as a quick reference guide, not as a replacement for assigned course work The reaction reagents are noted for illustrative purposes only, this should not serve as guide for lab experiment procedures. 

Note In hospital setting, the radioactive decay charts for radiopharmaceuticals may be used for quick reference to determine the percentage of radioactivity remaining at a given time. A representative decay chart for 13 I is shown in Table 15.4. 

For Quick Reference the Punch Capacity Graph below may 25 X Material multiplier be used to estimate punch force requirements for holes with known land lengths or diameters and thickness. Punching forces indicated are for mild steel. Punching forces for other materials may be determined by multiplying the chart value by the appropriate material multiplier. (See Charts on For punch force requirements in materials other than mild folfowing two pages.) steel use the material multiplier shown in the Material Specification Chart. Care must be taken as to material type and material hardness such as aluminums and stainless steels. 

The purpose of this chapter is to provide a quick reference/overview to near-infrared (NIR) spectroscopy calibrationists on the important aspects of quantitative or qualitative calibration techniques as illustrated by the flow chart in Figure 7.1. The main task of the computer in NIR spectroscopy, aside from driving the instrument or collecting data, is to interpret the spectra using a variety of multivariate mathematical techniques. These techniques are used to produce a mathematical calibration model. Figure 7.2 illustrates the various sample sets used for testing calibration models and the conditions where recalibration is indicated. The purpose of the calibration model is... 

Company SMS requirement 80% maximum thruster load. Following polar diagram of thruster loads was calculated (Fig. 6). On the diagram, which referred to NED coordinate system, loads of the how thrusters and azimuth stem thmsters were represented as MWTO DPS reactions on concrete EF disturbances. Reference to NED coordinate system allows DPO to plan easier MWTO movements and abortion route. This diagram could be attached to navigation chart or put near ECDIS screen for quick reference. 

In preparation for a field wide quick look correlation, all well logs need to be corrected for borehole inclination. This is done routinely with software which uses the measured depth below the derrick floor ( alonghole depth below derrick floor AHBDFor measured depth , MD) and the acquired directional surveys to calculate the true vertical depth subsea (TVSS). This is the vertical distance of a point below a common reference level, for instance chart datum (CD) or mean sea level (MSL). Figure 5.41 shows the relationship between the different depth measurements. 

For an unknown compound without a reference standard, important structural information can be obtained from the IR spectrum. Fig. 9 is a simplified illustration of the correlation between the absorption frequency incm and the functional groups (a more comprehensive description of this type of correlation chart is given in Ref. ). By observing the presence or absence of certain group frequencies, related to common functional groups such as -OH, -NH2, -CH3, -C=0, -CN, -C-O-C, -COOH, etc., the gross structural features of an unknown compound can be quickly determined. 

The latter are hence extremely useful to monitor the performance of an analytical method with time by setting up control charts which allow for the statistical control of measurements (33). Reference materials are necessarily homogeneous and stable. If analyzed at regular intervals, quick and clear information can be gained on any tendency for the analytical process to go out of control when the... 

This chapter starts with the fault finding chart. It is as wide ranging as possible but cannot hope to identify all of the quirks and idiosyncrasies of particular systems. Nevertheless, I hope it will provide a useful structure to the process of fault identification. The manufacturer referred to above also added that the number of things that can contribute to loss of resolution is almost limitless . I don t think we need to be as despondent as that most problems are easily identified and quickly resolved. The chart is followed by detailed descriptions and advice on particular problems identified within the chart itself. 

To identify a specific plastic, the detailed techniques of characterization available from different industry laboratories are used, as well as the more conventional chemical analysis and synthesis methods routinely performed in various laboratories. To provide a quick way of identifying plastics, refer to Figure 6-52 the following chart. It is only a guide, not foolproof. A detailed chart would cover a wide range of plastics (see Figure 6-52). 

A method which needs make no assumption about composition is based on charts developed by Maxwell and Bonnell (Reference 2). The method is published in imperial units and so pressure (P) must be converted to an absolute basis in units of mm Hg and the temperature (7) to an absolute basis in °R. The method will at first appear complex. However the end result is effective and simple to implement. The calculation can readily be implemented in a spreadsheet. This helps avoid the almost inevitable errors that will arise from using a calculator and provides a method that can quickly be applied to any column. 

Refers to bar charts on which the bars appear in descending (or varying) order of magnitude enabling quick identification of the most frequently occurring items. 

---