Polysulfonic block

See also PBT degradation structure and properties of, 44-46 synthesis of, 106, 191 Polycaprolactam (PCA), 530, 541 Poly(e-caprolactone) (CAPA, PCL), 28, 42, 86. See also PCL degradation OH-terminated, 98-99 Polycaprolactones, 213 Poly(carbo[dimethyl]silane)s, 450, 451 Polycarbonate glycols, 207 Polycarbonate-polysulfone block copolymer, 360 Polycarbonates, 213 chemical structure of, 5 Polycarbosilanes, 450-456 Poly(chlorocarbosilanes), 454 Polycondensations, 57, 100 Poly(l,4-cyclohexylenedimethylene terephthalate) (PCT), 25 Polydimethyl siloxanes, 4 Poly(dioxanone) (PDO), 27 Poly (4,4 -dipheny lpheny lpho sphine oxide) (PAPO), 347 Polydispersity, 57 Polydispersity index, 444 Poly(D-lactic acid) (PDLA), 41 Poly(DL-lactic acid) (PDLLA), 42 Polyester amides, 18 Polyester-based networks, 58-60 Polyester carbonates, 18 Polyester-ether block copolymers, 20 Polyester-ethers, 26... 

Sasaki et al. (3) prepared superacid sulfonic acid polysulfone block copolymers,... 

IHu Hu, D., Zheng, S.-X. Morphology and thermomechanical properties of epoxy thermosets modified with polysulfone-block-polydimethylsiloxane multiblock copolymer. J. Appl. Polym. Sci. 119 (2011) 2933-2944. 

The synthesis of block-copolymer went in two stages. At first, the polyester block of required molecular weight was produced while on the second stage that block (without separation) reacted to the polysulfonic block. The synthesis was carried out by the method of high-temperature polycondensation in the solution at 250 °C in environment of a-chlomaphthalene. The duration of the first stage was 1.5 h, and the second stage was 1 h. Obtained polymers exhibited liquid-crystal properties. 

The more certain approach leading to products in which the different component species must necessarily alternate along the chain is that involving the combination of two oligomers having mutually reactive end groups such that each species can react only with the other (equation 7). This procedure, which has been used particularly in recent work on polycarbonate-polysulfone and polysiloxane-polysulfone block copolymers, yields multiblock products with structures defined... 

Preparation and thermal crosslinking reactions of oc, -vinylbenzyl terminated polysulfone-b-polydimethylsiloxane, ABA type block copolymers have been discussed 282,313) However, relatively little characterization was reported. Molecular weights of polysulfone and PDMS segments in the copolymers were varied between 800-8,000 and 500-11,000 g/mole, respectively. After thermal curing, the networks obtained showed two phase morphologies as indicated by the detection of two glass transition temperatures (—123 °C and +200 °C) corresponding to PDMS and polysulfone phases, respectively. No mechanical characterization data were provided. 

In the last example, where p-chlorostyrene-12% DVB resin was sequentially polysulfonated and chlorinated and base treated to give resin E, characterized by high exchange capacity, stability and low bleed. We hypothesize that blocking the para position to sulfonation in the polymer leads to enhanced stability. 

Silicon-coated fiberglass Polysulfone resins Linear styrene block copolymers with butadiene/isoprene PP fibers... 

Copolymers. Copolymers from mixtures of different bisphenols or from mixtures of dichlorosulfone and dichlorobenzophenone have been reported in the patent literature. Bifunctional hydroxyl-terminated polyethersulfone oligomers are prepared readily by the polyetherification reaction simply by providing a suitable excess of the bisphenol. Block copolymers are obtained by reaction of the oligomers with other polymers having end groups capable of reacting with the phenol. Multiblock copolymers of BPA-polysulfone with polysiloxane have been made in this way by reaction with dimethyl amino-terminated polydimethylsiloxane the products are effective impact modifiers for the polyethersulfone (79). Block copolymers with nylon-6 are obtained when chlorine-terminated oligomers, which are prepared by polyetherification with excess dihalosulfone, are used as initiators for polymerization of caprolactam (80). 

PS PSF PSU PTFE PU PUR PVA PVAL PVB PVC PVCA PVDA PVDC PVDF PVF PVOH SAN SB SBC SBR SMA SMC TA TDI TEFE TPA UF ULDPE UP UR VLDPE ZNC Polystyrene Polysulfone (also PSU) Polysulfone (also PSF) Polytetrafluoroethylene Polyurethane Polyurethane Poly(vinyl acetate) Poly(vinyl alcohol) poly(vinyl butyrate) Poly(vinyl chloride) Poly(vinyl chloride-acetate) Poly(vinylidene acetate) Poly(vinylidene chloride) Poly(vinylidene fluoride) Poly(vinyl fluoride) Poly(vinyl alcohol) Styrene-acrylonitrile copolymer Styrene-butadiene copolymer Styrene block copolymer Styrene butadiene rubber Styrene-maleic anhydride (also SMC) Styrene-maleic anhydride (also SMA) Terephthalic acid (also TPA) Toluene diisocyanate Ethylene-tetrafluoroethylene copolymer Terephthalic acid (also TA) Urea formaldehyde Ultralow-density polyethylene Unsaturated polyester resin Urethane Very low-density polyethylene Ziegler-Natta catalyst... 

L.M. Robeson, A. Noshay, M. Matzner and C.N. Merian, Physical Property Characteristics of Polysulfone/poly(dimethyl siloxane) Block Copolymers, Angew. Makro-mol. Chem. 29, 47 (1973). 

Table 4.3 shows the permselectivity characteristics of pure, semicrystalline PEO films [76]. The selectivity characteristics for 02/N2 are rather similar to those for silicone rubber and natural rubber shown in Table 4.2. However, the values of permselectivity for C02 relative to the various light gases shown are all much higher than Table 4.2 shows for the rubbery polymers listed there and even for polysulfone except for C02/CH4. Comparison of the data in Tables 4.2 and 4.3 makes it clear that this high permselectivity of PEO stems from its high solubility selectivity for C02 versus other gases this is augmented by modest values of diffusivity selectivity. Data in Table 4.4 for the C02/N2 pair illustrate that this effect can be translated into various block-copolymer structures when the PEO content is high enough to ensure it is the continuous phase. In fact, nearly all these materials have higher permselectivity and solubility selectivity for C02/N2 than does pure PEO (see Table 4.3) however, the diffusion selectivity for these copolymers is much closer to, or even less than, unity than seen for pure PEO. Furthermore, the copolymers all have much higher absolute permeability coefficients than does PEO.

The polycarbonate oligomers were prepared by solution or interfacial techniques (10,17,18). Methylene chloride and tetraethyl ammonium chloride served as the solvent and phase transfer catalyst, respectively. The block copolymerizations were performed essentially under interfacial reaction conditions. In the case of copolymerizations using the Bis-S polysulfone oligomers, it was necessary to use tetrachloroethane as the organic solvent. 

The oligomer molecular weights were characterized by both UV-visible spectra (20, 21) and/or potentiometric titrations (22, 23). Details of the measurements are provided in these papers. The block copolymers also were characterized by intrinsic viscosity and in some cases by membrane osmometry and gel permeation chromatography. Additional characterization studies are continuing and will be reported later. A typical synthesis of a 5000-5000 polysulfone-S-polycarbonate-A copolymer via interfaciar polymerization is described below. 

Figure 3. High-temperature mechanical behavior of bis-A-polysulfone/bis-A-polycarbonate (16,000/17,000) block copolymer. Compression molded at 260°C.

Figure 8. Dynamic mechanical spectrum at higher temperatures for bis-S-polysulfone/bis-A-polycarbonate (10,000/10,000) block copolymer...

---