Polystyrene block copolymers with

It has been reported that block copolymers with appropriately chosen partners and mixing ratios yield materials suitable for use in substrate disks for optical data storage. An example is polyarjiate—polystyrene block copolymer with a PS content between 40 and 60% (225). 

Problem 11.16 A dual initiator, 4-hydroxy-butyl-2-bromoisobutyiate (HBBIB) was synthesized (Bernaerts et al., 2003) by the reaction of 1,4-butanediol with 2-bromoisobutyric acid using p-toluene sulfonic acid as catalyst in toluene. Suggest a scheme for the synthesis of well-de ned poly(tetrahydrofuran)-f>-polystyrene block copolymer with controlled molecular weights and low polydispersities using HBBIB. 

Figure 4. 200 MHz H-NMR Spectrum of a Polystyrene Recovered After Degrading a Polysiloxane-Polystyrene Block Copolymer with p-Toluene-sulfonic Acid Hydrate.

D.) Synthesis of Polyisobutylene and Polystyrene block copolymer with dltolylethylene. 

Proportion of Hard Segments. As expected, the modulus of styrenic block copolymers increases with the proportion of the hard polystyrene segments. The tensile behavior of otherwise similar block copolymers with a wide range of polystyrene contents shows a family of stress—strain curves (4,7,8). As the styrene content is increased, the products change from very weak, soft, mbbedike materials to strong elastomers, then to leathery materials, and finally to hard glassy thermoplastics. The latter have been commercialized as clear, high impact polystyrenes under the trade name K-Resin (39) (Phillips Petroleum Co.). Other types of thermoplastic elastomers show similar behavior that is, as the ratio of the hard to soft phase is increased, the product in turn becomes harder. 

Transparent toughened polystyrene polymers are produced by blending polystyrene with SBS block copolymers (see Section 11.8). During the 1970s and 1980s most development was with block copolymers with a radial (or star) shape. Two types were developed block copolymers with a central butadiene block, and block copolymers with a central polystyrene block. 

Polystyrene homopolymer produced by free radical initiators is highly amorphous (Tg = 100°C). The general purpose rubber (SBR), a block copolymer with 75% butadiene, is produced by anionic polymerization. 

Figure 7 shows the results of measurements of adsorption density by Parsonage, etal. [77] on a series of eighteen block copolymers, with poly(2-vinylpyridine) [PVP] anchors and polystyrene [PS] buoys, adsorbed from toluene (selective for PS) of variable molecular weight in each block. The results are presented as the reciprocal square of Eq. 28, that is, as a dimensionless number density of chains ct (d/Rg A)-2. For all but the copolymers of highest asymmetry, Eq. 28 is in good agreement with the data of Fig. 7. The high asymmetry copolymers are in the regime of the data of curves (a) and (c) of Fig. 3 where the large relative size...

Inoue T., Soen T., Hashimoto T., and Kawai, H. Studies on domain formation of the A-B t3fpe block copolymer with polystyrene and polyisoprene. Macromolecules, 13, 87, 1970. 

Block copolymers were synthesized by a combination of fipase-catalyzed polymerization and atom transfer radical polymerization (ATRE). " " At first, the polymerization of 10-hydroxydecanoic acid was carried out by using lipase CA as catalyst. The terminal hydroxy group was modified by the reaction with a-bromopropionyl bromide, followed by ATRP of styrene using CuCE2,2 -bipyridine as catalyst system to give the polyester-polystyrene block copolymer. Trichloromethyl-terminated poly(e-CL), which was synthesized by lipase CA-catalyzed polymerization with 2,2,2-trichloroethanol initiator, was used as initiator for ATRP of styrene. 

Consider a polystyrene-( )-polybutadiene star block copolymer with four arms coupled by a central Si-atom. Or consider a metal catalyst (e.g., Au) supported in activated carbon. Then the scattering of only the selected element (Si, Au, respectively) can be extracted [242], Even the distribution of the elements in the material can be mapped based on ASAXS data. A concise review of the ASAXS method in combination with AXRD and AWAXS has been published by Goerigk et al. [243]. 

Hyperbranched polymers have also been prepared via living anionic polymerization. The reaction of poly(4-methylstyrene)-fo-polystyrene lithium with a small amount of divinylbenzene, afforded a star-block copolymer with 4-methylstyrene units in the periphery [200]. The methyl groups were subsequently metalated with s-butyllithium/tetramethylethylenediamine. The produced anions initiated the polymerization of a-methylstyrene (Scheme 109). From the radius of gyration to hydrodynamic radius ratio (0.96-1.1) it was concluded that the second generation polymers behaved like soft spheres. 

We use polystyrene-Z>-polybutadiene block copolymers as the starting material with preformed polymer architecture. These polymers are comparatively cheap and easily accessible.1 For the present problems a series of narrowly distributed polystyrene-6-polybutadiene block copolymers with rather different molecular weights were synthesized via anionic polymerization (Figure 10.4, Table 10.1). As a test for the modification of technological products, a commercial triblock copolymer was also used. 

As the final products—polystyrene-h-polyivinylperfluorooctanoic ester)— form micelles in tetrahydrofuran (THF) as well as in DMF, there are not direct GPC data to characterize molecular parameter. For this reason, we employed esterification of the hydroxylated block copolymers with benzoylchloride as a model reaction to obtain a comparable product with molecular solubility that can easily be characterized by DMF-GPC. The GPC data from PSB-II—our largest and therefore most sensitive block copolymer—are summarized in Table 10.2. Results for all the other polymers are similar. 

The above data prove that the polystyrene-h-polybutadiene prepolymer is quantitatively transformed into block copolymers with perfluorinated side chains. The narrow molecular-weight distribution (I) = MW/MN) of the prepolymers is maintained by the described reaction sequence. 

The synthesis of block copolymers with blocks of ultralow cohesion energy densities on the basis of polystyrene-6-polybutadiene via two highly efficient polymer analogous reactions has been presented. 

A. Mayer et al. examined poly(dimethylsiloxane)-bIock-poly(ethylene oxide) (PDMS-b-PEO), poly(styrene)-f)Iock-poly(ethylene oxide) (PS-b-PEO), polystyrene-block-poly(methacryhc acid) (PS-b-PMAA) as amphiphihc block copolymers with regard to their properties in stabilizing colloidal metal nanoparticles [37, 49]. All three polymers are successfully used to stabihze various transition metal coUoids... 

Lohmeijer BGG, Schubert US (2004) Expanding the supramolecular polymer LEGO system nitroxide mediated living free radical polymerization for metallo-supramolecular block copolymers with a polystyrene block. J Polym Sci Part A Polym Chem 42 4016-4027... 

The living nature of the poly(styryl)anion allows one to prepare block copolymers with a great deal of control of the block copolymer structure. The preparation of diblock, triblock, and other types of multiblock copolymers has been reviewed [29-32]. Several of these block copolymers are in commercial use. The basic concept involves first preparing polystyrene block [RSt StLi—see Eq. (2)] and then adding a new monomer that can be added to start another growing segment. 

Chemically unlike polymers are incompatible, and it sometimes happens that the reaction medium is heterogeneous at the beginning. However, once some block copolymer is formed it acts as a "compatibilizer" and the reaction medium gradually becomes homogeneous. Many examples of such reactions could be quoted. A recent one is the hydrosilylation reaction carried out between a polystyrene fitted at a chain end with vinylsilane groups, and an a,u-dihydrogenopolydimethylsiloxane. This process is carried out at high concentration and it yields polystyrene-polydimethylsiloxane-polystyrene block copolymers. 2... 

Order-disorder transitions and spinodals were computed for linear multi block copolymers with differing sequence distributions by Fredrickson et al. (1992). This type of copolymer includes polyurethanes, styrene-butadiene rubber, high impact polystyrene (HIPS) and acrylonitrile-butadiene-styrene (ABS) block copolymers. Thus the theory is applicable to a broad range of industrial thermoplastic elastomers and polyurethanes. The parameter... 

---