Poly interaction

Of particular interest has been the study of the polymer configurations at the solid-liquid interface. Beginning with lattice theories, early models of polymer adsorption captured most of the features of adsorption such as the loop, train, and tail structures and the influence of the surface interaction parameter (see Refs. 57, 58, 62 for reviews of older theories). These lattice models have been expanded on in recent years using modem computational methods [63,64] and have allowed the calculation of equilibrium partitioning between a poly-... 

While the v-a plots for ionized monolayers often show no distinguishing features, it is entirely possible for such to be present and, in fact, for actual phase transitions to be observed. This was the case for films of poly(4-vinylpyri-dinium) bromide at the air-aqueous electrolyte interface [118]. In addition, electrostatic interactions play a large role in the stabilization of solid-supported lipid monolayers [119] as well as in the interactions between bilayers [120]. 

The term polymer is derived from the Greek words poly and meros, meaning many parts. We noted in the last section that the existence of these parts was acknowledged before the nature of the interaction which held them together was known. Today we realize that ordinary covalent bonds are the intramolecular forces which keep the polymer molecule intact. In addition, the usual type of intermolecular forces—hydrogen bonds, dipole-dipole interactions, and London forces—hold assemblies of these molecules together in the bulk state. The only thing that is remarkable about these molecules is their size, but that feature is remarkable indeed. 

A solubihty parameter of 24.5-24.7 MPa / [12.0-12.1 (cal/cm ) ] has been calculated for PVF using room temperature swelling data (69). The polymer lost solvent to evaporation more rapidly than free solvent alone when exposed to air. This was ascribed to reestabUshment of favorable dipole—dipole interactions within the polymer. Infrared spectral shifts for poly(methyl methacrylate) in PVF have been interpreted as evidence of favorable acid—base interactions involving the H from CHF units (70). This is consistent with the greater absorption of pyridine than methyl acetate despite a closer solubihty parameter match with methyl acetate. 

Unlike most crystalline polymers, PVDF exhibits thermodynamic compatibiUty with other polymers (133). Blends of PVDF and poly(methyl methacrylate) (PMMA) are compatible over a wide range of blend composition (134,135). SoHd-state nmr studies showed that isotactic PMMA is more miscible with PVDF than atactic and syndiotactic PMMA (136). MiscibiUty of PVDF and poly(alkyl acrylates) depends on a specific interaction between PVDF and oxygen within the acrylate and the effect of this interaction is diminished as the hydrocarbon content of the ester is increased (137). Strong dipolar interactions are important to achieve miscibility with poly(vinyhdene fluoride) (138). PVDF blends are the object of many papers and patents specific blends of PVDF and acryflc copolymers have seen large commercial use. 

Sodium Poly(4-styrene sulfonate). The sol—gel processing of TMOS in the presence of sodium poly-4-styrene sulfonate (NaPSS) has been used to synthesize inorganic—organic amorphous complexes (61). These sodium siUcate materials were then isotherm ally crystallized. The processing pH, with respect to the isoelectric point of amorphous siUca, was shown to influence the morphology of the initial gel stmctures. Using x-ray diffraction, the crystallization temperatures were monitored and were found to depend on these initial microstmctures. This was explained in terms of the electrostatic interaction between the evolving siUcate stmctures and the NaPSS prior to heat treatment at elevated temperatures. 

Sulfonation has been used to change some characteristics of blends. Poly(2,6-diphenyl-l,4-phenylene oxide) and polystyrene are immiscible. However, when the polymers were functionalized by sulfonation, even though they remained immiscible when blended, the functionalization increased interfacial interactions and resulted in improved properties (65). In the case of DMPPO and poly(ethyl acrylate) the originally immiscible blends showed increased miscibility with sulfonation (66). 

Because of the intractabiHty of poly(vinyHdene chloride), these studies have used copolymers containing various comonomers however, the results are beheved to be indicative of the interactions with vinyHdene chloride units and not primarily those of the comonomer. 

Blends of poly(vinyl chloride) (PVC) and a-methylstyrene—acrylonitrile copolymers (a-MSAN) exhibit a miscibiUty window that stems from an LCST-type phase diagram. Figure 3 shows how the phase-separation temperature of 50% PVC blends varies with the AN content of the copolymer (96). This behavior can be described by an appropriate equation-of-state theory and interaction energy of the form given by equation 9. 

Reaction of olefin oxides (epoxides) to produce poly(oxyalkylene) ether derivatives is the etherification of polyols of greatest commercial importance. Epoxides used include ethylene oxide, propylene oxide, and epichl orohydrin. The products of oxyalkylation have the same number of hydroxyl groups per mole as the starting polyol. Examples include the poly(oxypropylene) ethers of sorbitol (130) and lactitol (131), usually formed in the presence of an alkaline catalyst such as potassium hydroxide. Reaction of epichl orohydrin and isosorbide leads to the bisglycidyl ether (132). A polysubstituted carboxyethyl ether of mannitol has been obtained by the interaction of mannitol with acrylonitrile followed by hydrolysis of the intermediate cyanoethyl ether (133). 

The 1,1-disubstitution of chlorine atoms causes steric interactions in the polymer, as is evident from the heat of polymeri2ation (see Table 1) (24). When corrected for the heat of fusion, it is significantly less than the theoretical value of —83.7 kJ/mol (—20 kcal/mol) for the process of converting a double bond to two single bonds. The steric strain apparentiy is not important in the addition step, because VDC polymeri2es easily. Nor is it sufficient to favor depolymeri2ation the estimated ceiling temperature for poly (vinyhdene chloride) (PVDC) is about 400°C. 

Polymer/Polymer Complexes. PVP complexes with other polymers capable of interacting by hydrogen-bonding, ion-dipole, or dispersion forces. For example mixing of PVP with poly(acryHc acid) (PAA) in aqueous solution results in immediate precipitation of an insoluble complex (113). Addition of base results in dismption of hydrogen bonding and dissolution (114—116). Complexes with a variety of poly-acids (117) and polyphenols (118) have been reported. The interest in compatibiHty on a molecular level, an interesting phenomenon rarely found to exist between dissimilar polymers, is favored by the abiHty of PVP to form polymer/polymer complexes. 

A large number of polymeric substances, (RAs) or (ArAs), are also known (113). They are usually prepared by the reduction of arsonic acids with hypophosphorous acid (100,114) or sodium dithionite (115). Most of these polymers have not been well characterized. An insoluble, purple material, poly(methylarsinidene) [26403-94-1], (CH As), prepared by the interaction of methylarsine and a dihalomethylarsine, however, has been shown by an x-ray investigation to have a ladderlike polymeric stmcture in which the inter-mng distances correspond to one-electron bonds (116) ... 

It has, however, been possible to find solvents for some polar crystalline polymers such as the nylons, poly(vinyl chloride) and the polycarbonates. This is because of specific interactions between polymer and solvent that may often occur, for instance by hydrogen bonding. 

Comparison of Table 5.4 and 5.7 allows the prediction that aromatic oils will be plasticisers for natural rubber, that dibutyl phthalate will plasticise poly(methyl methacrylate), that tritolyl phosphate will plasticise nitrile rubbers, that dibenzyl ether will plasticise poly(vinylidene chloride) and that dimethyl phthalate will plasticise cellulose diacetate. These predictions are found to be correct. What is not predictable is that camphor should be an effective plasticiser for cellulose nitrate. It would seem that this crystalline material, which has to be dispersed into the polymer with the aid of liquids such as ethyl alcohol, is only compatible with the polymer because of some specific interaction between the carbonyl group present in the camphor with some group in the cellulose nitrate. 

The solubility parameter of poly(ethylene terephthalate) is about 21.8 MPa but because it is a highly crystalline material only proton donors that are capable of interaction with the ester groups are effective. A mixture of phenol and tetrachloroethane is often used when measuring molecular weights, which are about 20 000 in the case of commercial polymers. 

VV -values for bromoform and pyrrole, acidic liquids, against poly(vinyl chloride), an acidic polymer, and dimethyl sulfoxide, a predominantly basic liquid, against polyfmethyl methacrylate), a basic polymer, but large values for the acidic liquids against PMMA and the basic liquid against PVC. 2-Iodoethanol, a bifunctional liquid, showed appreciable -values with both polymers. Despite these results in line with expectations, other results based on wettability measurements are not so clear-cut. For example, Vrbanac [94] found significant apparent acid-base interactions of various aromatic liquids against poly(ethylene), presumably a neutral substrate. 

---