Phosphazene

Properties. One of the characteristic properties of the polyphosphazene backbone is high chain dexibility which allows mobility of the chains even at quite low temperatures. Glass-transition temperatures down to —105° C are known with some alkoxy substituents. Symmetrically substituted alkoxy and aryloxy polymers often exhibit melting transitions if the substituents allow packing of the chains, but mixed-substituent polymers are amorphous. Thus the mixed substitution pattern is deUberately used for the synthesis of various phosphazene elastomers. On the other hand, as with many other flexible-chain polymers, glass-transition temperatures above 100°C can be obtained with bulky substituents on the phosphazene backbone. 

Phosphazene polymers are inherently good electrical insulators unless side-group stmctures allow ionic conduction in the presence of salts. This insulating property forms the basis for appHcations as wire and cable jackets and coatings. Polyphosphazenes also exhibit excellent visible and uv radiation transparency when chromophoric substituents are absent. 

Another valuable characteristic of many phosphazene polymers is their flame-retardant behavior and low smoke generation on combustion (13). This property is utilized in commercial appHcations. 

A remarkable feature of phosphazene polymers of types (1) and (2) is that appropriate substituents (which are readily attached) can be used as toggle switches to turn several properties, such as hydrolytic stabiHty and electrical conductivity, on and off (1). 

Applications. Among the P—O- and P—N-substituted polymers, the fluoroalkoxy- and aryloxy-substituted polymers have so far shown the greatest commercial promise (14—16). Both poly[bis(2,2,2-trifluoroethoxy)phosphazene] [27290-40-0] and poly(diphenoxyphosphazene) [28212-48-8] are microcrystalline, thermoplastic polymers. However, when the substituent symmetry is dismpted with a randomly placed second substituent of different length, the polymers become amorphous and serve as good elastomers. Following initial development of the fluorophosphazene elastomers by the Firestone Tire and Rubber Co., both the fluoroalkoxy (EYPEL-F) and aryloxy (EYPEL-A) elastomers were manufactured by the Ethyl Corp. in the United States from the mid-1980s until 1993 (see ELASTOLffiRS,SYNTHETic-PHOSPHAZENEs). 

PHOSPHAZENES CONTAINING SKELETAL CARBON, SULFUR, AND METAL ATOMS... 

The first phosphazene polymers containing carbon (79), sulfur (80,81), and even metal atoms (82) in the backbone have been reported. These were all prepared by the ring-opening polymerization of partially or fully chloro-substituted (or fluoro-substituted) trimers containing one hetero atom substituting for a ring-phosphoms atom in a cyclotriphosphazene-type ring. 

M. Zeldin, K. J. Wynne, and H. R. AUcock, eds.. Inorganic and Organometallic Poljmers, ACS Symposium Series, Vol. 360, American Chemical Society, Washington, D.C., 1988 regarding poIy(phosphazenes), poly(silanes), and other polymers. 

See Elastopiers.synthetic-phosphazenes Inorganic high polymers. 

Not inclusive see also Acrylic elastol rs, Phosphazenes, Cm OROSULFONATED polyethylene, Eethylene-acrylic elastot rs, Polyethers under the tide ElASTOT RS, SYNTTiETIC. 

Phosphazene polymers are normally made in a two-step process. First, hexachlorocyclotriphosphazene [940-71 -6J, trimer (1), is polymerized in bulk to poly(dichlorophosphazene) [26085-02-9], chloropolymer (2). The chloropolymer is then dissolved and reprecipitated to remove unreacted trimer. After redissolving, nucleophilic substitution on (2) with alkyl or aryloxides provides the desired product (3). 

---