Phase reacted

Another type of polyol often used in the manufacture of flexible polyurethane foams contains a dispersed soHd phase of organic chemical particles (234—236). The continuous phase is one of the polyols described above for either slab or molded foam as required. The dispersed phase reacts in the polyol using an addition reaction with styrene and acrylonitrile monomers in one type or a coupling reaction with an amine such as hydrazine and isocyanate in another. The soHds content ranges from about 21% with either system to nearly 40% in the styrene—acrylonitrile system. The dispersed soHds confer increased load bearing and in the case of flexible molded foams also act as a ceU opener. 

Figure 4b represents the case where a reactant dissolved in the dispersed phase reacts with the continuous phase to produce a co-reactant. The co-reactant and any remaining unreacted original reactant left in the dispersed phase then proceed to react with each other at the dispersed phase side of the interface and produce a capsule shell. Capsule shell formation occurs entirely because of reaction of reactants present in the droplets of dispersed phase. No reactant is added to the aqueous phase. As in the case of the process described by Figure 4a, a reactive species must be dissolved in the core material in order to produce a capsule shell. 

A specific example of the process represented by Figure 4b occurs when a multihmctional isocyanate is dissolved in a Hquid, water-immiscible core material and the mixture produced is dispersed in an aqueous phase that contains a dispersing agent. The aqueous phase reacts with some of the isocyanate groups to produce primary amine functionaHties. These amino groups react with unreacted isocyanate groups to produce a polyurea capsule shell (13). 

CaO 7AI2O2, occur in minor amounts in the 80% AI2O2 CAC products. The phase reacts rapidly with water to initiate hydraulic... 

This reaction can also be mn in a continuous fashion. In the initial reactor, agitation is needed until the carbon disulfide Hquid phase reacts fully. The solution can then be vented to a tower where ammonia and hydrogen sulfide are stripped countercurrendy by a flow of steam from boiling ammonium thiocyanate solution. Ammonium sulfide solution is made as a by-product. The stripped ammonium thiocyanate solution is normally boiled to a strength of 55—60 wt %, and much of it is sold at this concentration. The balance is concentrated and cooled to produce crystals, which are removed by centrifiigation. 

In these early reactions the reactivities of the individual phases are important in determining the overall reaction rate. However, as the cement particles become more densely coated with reaction products, diffusion of water and ions in solution becomes increasingly impeded. The reactions then become diffusion-controUed at some time depending on various factors such as temperature and water—cement ratio. After about 1 or 2 days, ie, at ca 40% of complete reaction, the remaining unhydrated cement phases react more nearly uniformly. 

Reactant in tbe Gas Phase When A in the gas phase reacts with adsorbed B,... 

DEF. A peritectoid is a three-phase reaction by which, on cooling, two solid phases react to give a single new solid phase. 

In this case study, an enzymatic hydrolysis reaction, the racemic ibuprofen ester, i.e. (R)-and (S)-ibuprofen esters in equimolar mixture, undergoes a kinetic resolution in a biphasic enzymatic membrane reactor (EMR). In kinetic resolution, the two enantiomers react at different rates lipase originated from Candida rugosa shows a greater stereopreference towards the (S)-enantiomer. The membrane module consisted of multiple bundles of polymeric hydrophilic hollow fibre. The membrane separated the two immiscible phases, i.e. organic in the shell side and aqueous in the lumen. Racemic substrate in the organic phase reacted with immobilised enzyme on the membrane where the hydrolysis reaction took place, and the product (S)-ibuprofen acid was extracted into the aqueous phase. 

Processes in which two phases react and result in the formation of a third form an important group of gas-liquid-particle processes. In the production of acetylene, a gaseous phase is formed by reaction between a liquid and a particle phase water and carbide. In the production of gas hydrates in desalination processes, a particle phase is formed by reaction between a liquid and a gaseous phase sea water and, for example, propane. In the melting of gas-hydrate or ice crystals a liquid phase is formed when gaseous and particle phases are brought in contact. 

Klunder A. J. H., Zwanenburg B. Gas Phase Thermolysis in Natural Product Synthesis in Gas Phase React. Org. Synth. 1997 107, Ed. Yannick V., Pb. Gordon and Breach, Amsterdam... 

In this chapter, we consider multiphase (noncatalytic) systems in which substances in different phases react. This is a vast field, since the systems may involve two or three (or more) phases gas, liquid, and solid. We restrict our attention here to the case of two-phase systems to illustrate how the various types of possible rate processes (reaction, diffusion, and mass and heat transfer) are taken into account in a reaction model, although for the most part we treat isothermal situations. 

A liquid phase reacting system has the simultaneous reactions, A b B and... 

A solute A in a gas phase reacts with B in the liquid phase by a second order reaction. Some results of a numerical solution by Perry Pigford (Ind Eng Chem 45 1247, 1953) for the enhancement factor are fitted by the equation... 

Fig. 1.5 Arrhenius plot of diffusion coefBcients versus reciprocal temperatures for various minerals. Data from phases reacted under wet conditions are given as solid lines, whereas dry conditions are represented by dashed lines. Note that the rates for dry systems are generally lower and have higher activation energies (steeper slopes). (Modified after Cole and Chakraborty 2001)...

In a well-mixed emulsion reactor A in a continuous aqueous phase reacts with B in an organic drop phase in the reaction A + B products. The reaction is very fast and is limited by the diffusion of A into the organic phase. The feeds are 1 liter/min of 9 molar A and 1 liter/min of 2 molar B. The stirring is such that the drops are monodisperse at a diameter of 200/fm. 

Also, boron can be analyzed by colorimetry techniques (APHA, AWWA, and WEF. 1999. Standard Methods for the Examination of Water and Wastewater, 20th ed. Washington DC American Public Health Association). Boron in acidified aqueous phase reacts with curcumin to form a red-colored product, roso-cyanine. Presence of calcium and magnesium at high concentrations can interfere in the test. Another colorimetric measurement involves the reaction of boron with carmine or carminic acid in concentrated sulfuric acid. The color of the solution changes from bright red to bluish red or blue, depending on boron concentration. 

Acute phase react ant s for efficacy in rheumatoid arthritis pain, stiffness, number of swollen joints, range of motion, functional capacity, structural damage fecal occult... 

Limiting reactant in three-phase reacting systems... 

In many cases it will not be acceptable to relieve a two-phase reacting mixture direct to the atmosphere. Factors to be considered121 include ... 

---