Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Parameters window

A more recent process, the P2 etch [60], which uses ferric sulfate as an oxidizer in place of sodium dichromate avoids the use of toxic chromates, but still provides a similar oxide surface morphology (Fig. 15) allowing a mechanically interlocked interface and strong bonding [9]. The P2 treatment has wide process parameter windows over a broad range of time-temperature-solution concentration conditions and mechanical testing confirms that P2-prepared surfaces are, at a minimum, equivalent to FPL-prepared specimens and only slightly inferior to PAA-prepared surfaces [61]. [Pg.964]

Use the Curve Fit tool to obtain optimal results automatically. Document the differences to the manually obtained results. Clicking CURVE-FIT will allow the selection of the variable to be fit to the experimental data and the parameters to be determined. For each parameter, two initial guessed values and the maximum and minimum allowable values can be entered. Limit k, and k2 to positive values. On running under CURVE-FIT, the values of the required parameters are repeatedly updated until the final converged values are obtained. The updated values can be found in the Parameter Window. [Pg.263]

Go to Parameters/Parameter Window on the menu and see how the values are set. They may be different than on the program listing. Those with a can be reset to the original values. Also, if necessary, here the integration... [Pg.597]

Decide on further runs. It is most common to want to compare runs for different values of the parameters. This is usually done with Parameter/Batch Runs and also with Model/Defme Sliders. If the overlay button is set, then more than one set of runs can be graphed on top of the first run. Sometimes more than one parameter needs to be set this is best done with changes done in the Parameters/Parameter Window, with an overlay graph if desired. [Pg.598]

A Parametric Plot choosing the final value can be used to find the influence of one variable on the steady state. The second parameter can be changed in the Parameter Window and additional parametric runs made and plotted with an overlay plot. Thus it is possible to obtain a sort of contour plot with a series of curves for values of the second parameter. Unfortunately, no automatic contour plot is yet possible. [Pg.600]

This guide is intended as a supplementary introduction to MADONNA, donna Flit Edit Flowchart Model Compute Graph Parameters Window Help... [Pg.602]

Fig. 4 The MODEL/EQUATIONS was chosen. Seen here is also the PARAMETER WINDOW. Fig. 4 The MODEL/EQUATIONS was chosen. Seen here is also the PARAMETER WINDOW.
Note The fonts for the title and the parameter windows must be set interactively by double clicking the conesponding windows with your left mouse button which opens a corresponding dialog box. [Pg.115]

Click the Output Font... button and define the output fonts for and the style according to your preferences. Note that this influcences only the fonts in the Spectrum window (peak picking values, scale (ppm/Hz) values), but not the fonts for the title and parameter windows of the plot layout. The latter fonts may be set with the Preview option (4.7.3). [Pg.115]

In general, the page layout consists of these three individual windows, the Text window for the title, the Trace window for the 2D matrix, with space left for projections, and the Parameter window. [Pg.140]

Although the term electron-phonon coupling is used here, the discussion applies equally to coupling with an electro-magnetic source. In any event, in order to retain the coherence of the electrons at the given T, the system has to be sufficiently small. At the same time, the strength of the acoustic source is assumed to be such that the additional decoherence it causes is not detrimental. The precise parameter windows in which this can be achieved will be sensitive to acoustic mismatch, details of the sample geometries, etc. [Pg.78]

The parameters windows of the automated microreaction system AuMpRes are given in Table 4.9. These specifications allow the operation of most liquid reactions [108],... [Pg.577]

Table 4.9 Parameter windows of the AuM jRes automated micro reaction system. Table 4.9 Parameter windows of the AuM jRes automated micro reaction system.
The type of potential is chosen in the Edit/View Force Field Atom Type Parameters window of MOMEC. Note that the corresponding functions also need to be activated in the Setup/Optimization controls menu. [Pg.232]

Repeat step 10 for the other torsion angle setting a starting value of 45° and a step size of 0°. The Setup Energy Parameters window should appear as shown in Fig. 17.15.4. [Pg.265]

Nj, y,j, ctj, y0j being simple rational numbers.) As the Brouwer conditions are only valid within certain parameter windows (belonging to the Po2 -T -plane) and change from window to window, Eq. (33) is... [Pg.18]

After you set the hardware and software parameters, Windows 95 will present you with a screen that will allow you to set the date, time, and time zone (Figure 13.18) of the computer. [Pg.545]

A, C, D. The most common Windows printing problems are that the print spool is stalled, there s an incorrect/incompatible driver for print, or there s an incorrect parameter. Windows will support almost any type of printer model. [Pg.805]

Fig. 14. Distribution of the order parameter A in different order parameter windows for pathways of a given length t left hand side). Matching the distributions in the windows where they overlap yields the distribution over the full order parameter range from the reactant region to the product region right hand side). The data are from simulations of proton transfer in the protonated water trimer... Fig. 14. Distribution of the order parameter A in different order parameter windows for pathways of a given length t left hand side). Matching the distributions in the windows where they overlap yields the distribution over the full order parameter range from the reactant region to the product region right hand side). The data are from simulations of proton transfer in the protonated water trimer...
Choose Compute/Run and specify the variables to be used in the graph window from Parameters/Parameter Window. Click OK and the graph will be made. [Pg.282]

Parameter Window Define tliden-Shaw Sliders 0> P... [Pg.628]

Figure 6. An overlay graph for three values of kl as selected in the Parameter Window. Figure 6. An overlay graph for three values of kl as selected in the Parameter Window.
Schmidt, T., Gartner, F., Assadi, H., and Kreye, H. (2006) Development of a generalized parameter window for cold spray deposition. Acta Mater., 54 (3), 729-742. [Pg.246]

The formation of pinholes due to surface roughening can be avoided by optimization of the film deposition parameters. Experience shows, however, that the processing parameter window can be narrower than desired for a reproducible fabrication procedure. The use of a non-superconducting multilayer interspersing YBCO layers is a solution to the problem of irreproduci-bility. The use of SrTiOs/PrGaOs (STO/PGO) intermediate multilayers is an example of a successful combination which significantly opens the processing window [14.76]. [Pg.383]

When a stable operating plant is designed, the influence of some key process parameters, such as temperature, pressure or concentrations, is estimated by experiments at two extreme values. This gives a first guess at a parameter window and/or an idea of how to modify the parameters for process optimization. [Pg.1267]

GUI image of the parameter window for an MS/MS To In Silico Comparison as displayed in the USDA... [Pg.568]

In the Line Balance Parameters window select Number of WSA olume combination. Enter 1000 in the Volume section and 2 in the No of WS. Click on Show button. It will show the amount of time required to produce this volume at maximum workstation efficiencies. Click on Accept button. It will open the Line Balance Results window. [Pg.70]

Design of the process parameter window Should be able to conduct a parametric study of the effect of various disturbances on the flow and determine a process window which will ensure complete filling. [Pg.299]


See other pages where Parameters window is mentioned: [Pg.635]    [Pg.80]    [Pg.83]    [Pg.230]    [Pg.230]    [Pg.603]    [Pg.145]    [Pg.99]    [Pg.102]    [Pg.282]    [Pg.108]    [Pg.63]    [Pg.398]    [Pg.56]    [Pg.650]    [Pg.564]    [Pg.385]    [Pg.2087]   
See also in sourсe #XX -- [ Pg.16 ]




SEARCH



© 2024 chempedia.info