OXYGEN Well water

A substantial fraction of the named enzymes are oxido-reductases, responsible for shuttling electrons along metabolic pathways that reduce carbon dioxide to sugar (in the case of plants), or reduce oxygen to water (in the case of mammals). The oxido-reductases that drive these processes involve a small set of redox active cofactors , that is, small chemical groups that gain or lose electrons. These cofactors include iron porjDhyrins, iron-sulfur clusters and copper complexes as well as organic species that are ET active. 

If poUed, most aquaculturists would probably indicate a preference for well water. Both freshwater and saline wells are common sources of water for aquaculture. The most commonly used pretreatments of well water include temperature alteration (either heating or cooling) aeration to add oxygen or to remove or oxidize such substances as carbon dioxide, hydrogen sulfide, and iron and increasing salinity (in mariculture systems). Pretreatment may also include adjusting pH, hardness, and alkalinity through the appHcation of appropriate chemicals. 

Foulants enter a cooling system with makeup water, airborne contamination, process leaks, and corrosion. Most potential foulants enter with makeup water as particulate matter, such as clay, sdt, and iron oxides. Insoluble aluminum and iron hydroxides enter a system from makeup water pretreatment operations. Some well waters contain high levels of soluble ferrous iron that is later oxidized to ferric iron by dissolved oxygen in the recirculating cooling water. Because it is insoluble, the ferric iron precipitates. The steel corrosion process is also a source of ferrous iron and, consequendy, contributes to fouling. 

The corrosivity of a natural water depends on the concentration and type of impurity dissolved in it and especially on its oxygen content. Waters of similar oxygen content have generally similar corrosivities, e.g. well-aerated quiescent sea-water corrodes cast iron at ratesof 0 05-0-1 mm/y while most well-aerated quiescent fresh waters corrode iron at O Ol-O-1 mm/y. 

An important virtue of the Heck reaction is that it can be applied with much success to essentially every type of olefin, although electron-deficient olefins are particularly well-suited. Moreover, the Heck reaction tolerates a variety of functional groups, and often does not require rigorous exclusion of oxygen and water.llb In fact, many alkene arylations proceed very efficiently in water.14... 

Normally, the cascade from oxygen to water is well controlled by SOD, catalase and endogenous antioxidants such as glutathione, ascorbate and vitamin E. Vitamin E is the most important membrane-bound antioxidant. However, during ischaemia, the local control of ROS is lost, thus reactive free radicals can attack the membranes and lipid peroxidation begins. Endogenous antioxidants can be supplemented. This section describes this supplementation strategy. 

Corrosion is a mixed-electrode process in which parts of the surface act as cathodes, reducing oxygen to water, and other parts act as anodes, with metal dissolution the main reaction. As is well known, iron and ferrous alloys do not dissolve readily even though thermodynamically they would be expected to, The reason is that in the range of mixed potentials normally encountered, iron in neutral or slightly acidic or basic solutions passivates, that is it forms a layer of oxide or oxyhydroxide that inhibits further corrosion. 

The laccases, classed as polyphenol oxidases, catalyze the oxidation of diphenols, polyamines, as well as some inorganic ions, coupled to the four-electron reduction of oxygen to water see Fig. 12.4 for the proposed catalytic cycle. Due to this broad specificity, and the recognition that this specificity can be extended by the use of redox mediators [27], laccases show promise in a range of applications [28], from biosensors [29-32], biobleaching [27, 33-35] or biodegradation [36], to biocatalytic fuel cells [1-3, 18, 26, 37-42]. 

The primary product from Fischer-Tropsch synthesis is a complex multiphase mixture of hydrocarbons, oxygenates, and water. The composition of this mixture is dependent on the Fischer-Tropsch technology and considerable variation in carbon number distribution, as well as the relative abundance of different compound classes is possible. The primary Fischer-Tropsch product has to be refined to produce final products, and in this respect, it is comparable to crude oil. The primary product from Fischer-Tropsch synthesis can therefore be seen as a synthetic crude oil (syncrude). There are nevertheless significant differences between crude oil and Fischer-Tropsch syncrude, thus requiring a different refining approach.1... 

Initial studies, described here, involved the use of an ultrahigh vacuum (UHV) surface-analytical instrument coupled to an antechamber. The antechamber allows experiments in solution and electrochemical treatments without transfer of samples outside of the system s controlled atmosphere. Focusing on the chemistry of copper surfaces in aqueous environments suggests the importance of studying the initial stages of surface reactivity with oxygen and water. Electrochemical experiments involve electrolytes thus their surface reactivity should be studied as well. 

---